Package Contents: Item Qty.
Table of Contents: 1 General Instructions...................................................................................... 3 1.1 Safety Instructions ............................................................................ 3 1.2 Warnings ........................................................................................... 3 2 Features ........................................................................................................ 4 2.2 Product Features..................................
1 General Instructions: 1.1 Safety Instructions: Make sure to read the user manual before using the product. Always follow national and local safety codes during the installation. Only qualified and experienced person can carry this installation and maintenance. Use reliable tools, not complying can result in serious injury. Make sure that the environmental conditions meet the installation requirements for this product.
2 Features: 2.1 Product Picture: 2.2 Product Features Alarm I/O. Adaptive PELCO-P/D protocol. Adjustable IR illumination. Memory recall. Real-Time-Control: call any functions at any time. Up to 8 privacy masks. Support 128 preset positions. English OSD menu, user friendly for smooth operation. Proportional zoom. Auto flip function. Built in lightning proof and surge proof. Advanced step motor: Less heat, Smooth movement, No-shaking.
speed to reduce the dark angle and flashlight effect. The upper dome adopts 7" aluminum alloy structure for better magnetic shield and heat radiation. The underpart dome adopts full metal class points bin type design for fast heat dissipation and anti-mist, non-interference light source images and long life span IR light. 2.3 Specifications: Power Supply Max.
RTC Set any functions at any time Superpower LED：Default: Zoom x1~5: open the near-distance IR lights; Zoom x6~9: open the IR Light switch near-distance and middle-distance IR lights; Zoom >x10: turn off the near-distance IR lights, open the middle-distance and far-distance IR lights. Work Indoor：0℃～+50℃； Temperature Outdoor ：-20℃～+50℃ (with heater) Work Humidity <90% 3 Installation Site Preparations: 3.
3.3 DIP Switch Setting: (1)Default Settings: Pelco P/D (auto-detected), baud rate: 2400, address: 1.
4 Setup of the OSD Menu: 4.1 Display Boot-UP Info. Before installation please check the protocol, baud rate, address and RS485 data cable. Default protocol: PELCO-D, address: 1, baud rate: 2400. PROTOCOL: PELCO P D BAUD RATE: 2400BPS CAMERA ID: 001 CAMERA S/N: 0000000001 MODEL: ----------------- VERSION: V1.02 FAN SPEED: 6000RPM STARTING… ….
The Main menu as follows: SYSTEM LENS CAMERA PAN/TILT AUTO RUNNING PRIVACY MASK ALARM LANGUAGE IR SET EXIT 4.
System info includes following settings. < SITE INFO>: In this menu the user can setup the dome’s name, View the Hardware address, change the camera software address and choose the leading command (Hardware or Software). < DISPLAY SETUP >: In this menu the user can choose which details will display on the camera Screen. The available options are: Site name, Preset title, Pattern name, Zoom, Orientation, Temperature, Zone name and RTC time.
: The title name of the dome. Assigning a name to a dome helps the user to identify which dome is under control for multiple domes site. Max 16 digits Setting with number from 0~9 and letter from A~Z. Move the cursor to and then move the joystick right to enter dome ID setting, : Setting the address method that controls the dome, user can choose from SOFT (Software) and HARD (Hardware).
4.3.2 DISPLAY SET UP < Main Menu> SITE NAME: OFF PRESET TITLE: OFF PATTERN NAME: OFF ZOOM: OFF ORIENATATION: OFF TEMPRETURE: OFF ZONE NAME: OFF RTC TIME: OFF BACK EXIT ：Choose to display site name or not. ：Choose to display preset position or not. ：Choose to display pattern name or not ：Choose to display the current zoom or not. ：Choose to display the current lens direction or not.
4.3.3 DISPLAY BOOT-UP INFO PROTOCOL: PELCO P D BAUD RATE: 2400BPS CAMERA ID: 001 CAMERA S/N: 0000000001 MODEL: ----------------- VERSION: V1.02 FAN SPEED: 6000RPM CALL PRESET 1 TO BACK Enter into Boot-up info displays to check current setup, call preset 1 to return to upper menu 4.3.
password. If the old Password input is not correct, you will not be able to change the password. : Re-input the new password and confirm. If the input is not the same as the first time input, the system will remain the old password. : Switch on / off the password protection. When it is user need to enter password in order to access OSD menu or save preset through keyboard. : return to upper menu. : exit the menu 4.3.
Use left and right keys to move the cursor to desired item, use up and down keys to change the current cursor value. 4.3.8 RTC RIME RUNNING
: Set the zoom speed level to HIGH or LOW : Turn On/Off the Digital Zoom. : Set up Auto Focus (AF), Auto Iris (AI) or Both : Joystick movement triggers both auto focus and auto iris ： Joystick movement triggers auto focus only : Joystick movement triggers auto iris only. : Joystick movement triggers none of the functions.。 : This item sets the time to restore auto focus after focus is manually changed.
: Show the current camera P/N (PAL/ NTSC), The PTZ can automatically detected some of the camera Signal mode. If not, please set manually. 4.5 CAMERA: Important Note: Camera setting will vary between Z-22IR and Z-27IR. For the Simple camera menu access . Simple Camera Menu: WHITE BALANCE: AUTO BLC MODE BACK EXIT White Balance is normally compensated for by the automatic white balance gain control.
dark. The dome can auto adjust the brightness of the whole image according to the brightness of the center point. Thus backlight compensation can increase the brightness of the objects in the center of the picture. Select, and choose the right key to access the sub-menu as below BLC QTY: 000 WDR: OFF BACK EXIT [BLC QTY]: Adjust the data of the BLC, choose from 000-255 [WDR]: ON and OFF the camera’s WDR function (Not supported) Advanced Camera Menu: For advanced Menu, Call preset #69.
FOCUS AUTO ID DISPLAY OFF CAM ID 1 PROTOCOL VISCA BAUD RATE 9600 485 CONTROL NORMAL LED 1 8 LED 2 15 LANGUAGE ## RESET EXIT DSP Settings: SHUTTER AUTO WB MODE AUTO AGC 88 DNR ON BACKLIGHT OFF HLC LEVEL 48 MIRROR OFF BRIGHTNESS 8 SHARPNESS 8 COLOR 8 EXIT 19
: Choosing between Auto and Manual : White Balance is normally compensated for by the automatic white balance gain control. In some lighting conditions, user may want to manually adjust the red and blue settings for optimal viewing. There are 6 options: [AUTO]: Auto White Balance (default setting). [MANUAL]: Manually set the red and blue values, setup from 000 to 255. [ATW]: Auto track White Balance.
4.6 PAN/TILT AUTO STOP TIME: OFF SPEED AMPLIFY: OFF PROPORTIONAL P/T: ON SET NORTH BACK EXIT : For some particular protocols, the dome will not stop moving even there is no operation on CCTV Tester. This menu sets the time after which the dome receives last control command. [Off]: Disable this function [001~255]: The time (second) that dome will stop moving without receiving any commands.
: User can set orientation by using joystick to position north. When select , following menu will pop-up. CALL PRESET 1 TO RETURN CONFIRM. . . . . . Adjust the lens to desired position and call preset 1 to confirm and return. 4.
4.7.1 PRESET PRESET NUMBER: TITLE: 001 PRESET 001 SET CURRNET REMOVE CURRENT BACK EXIT In this function, the values of the pan/tilt positions will be stored in the desired memory slot so that you will be able to call it when in need. 128 presets can be saved. It could also setup by shortcuts of control system.
CALL PRESET 1 TO BACK CONFIRM … … Move to the desired position and zoom to a suitable level, call preset 1 to save the current preset and return. < REMOVE CURRENT>: Delete the preset with the number and title display above. 4.7.2 TOUR TOUR NUMBER: 001 DWELL: 003 EDIT RUN BACK EXIT The dome camera will run repeatedly as the given sequence of presets at certain dwell time by one command. Max. 4 tours available (27preset/tour).
PRESET–DWELL 000-003 000-003 000-003 000-003 000-003 000-003 000-004 000-003 000-003 000-003 000-003 000-003 000-003 000-003 000-003 000-003 000-003 000-003 000-003 000-003 000-003 000-003 000-003 000-003 000-003 000-003 000-003 SAVE AND BACK CANCEL AND BACK There are three group numbers, the left side is preset number, the right side is dwell time; tour from left to right, up to down in the order to run preset; when the preset number is set to < 000>, the current preset is skipped; : Save
There are max 4 patterns, and the dome camera can record all regular operation in 3 minutes at least. The command will drive the speed dome runs as given route repeatedly. : Set current pattern number from 001～004. : Edit the current pattern’s running route and record all operation in 3 minutes at least. CALL PRESET 1 TO BACK CONFIRM… … 180S 000% RECORD………. [180S]: Remaining record time. [000%]: The recording space. The record time will decrease while the space increases.
<360° SCAN DWELL>: [0S]: 360 continuous scan [5S]: 90 intermittent scan, then dwell on 5s, the dome will continuously run at the given route repeatedly until receiving new command. [10S]: 90 intermittent scan, then dwell on 10s, the dome will continuously run at the given route repeatedly until receiving new command. High：20/S Middle：15/S Low：6/S Auto：Do as the camera’s proportional P/T speed. The dome will continuously run at the given route repeatedly until receiving new command.
- : To set current zone Name, 16-bit can be set up by the number 0-9 and the letters A-Z of any combination <left limit>: Set the right edge of region <a> CALL PRESET 1 TO BACK CONFIRM. . . . . . Move the camera left limit position to confirm and return. The position of the left limit position will now be marked on the menu screen. <right limit>: Set the right edge of region (B) CALL PRESET 1 TO BACK CONFIRM. . . . . . Move the camera right limit position to confirm and return.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/provision-isr/pz-22ir/user-manual-english/page-30.html>PAGE 30</a></h6><p>4.7.6 <park time> The camera will run certain function automatically if the dome is not receiving any command for the specified time. 0S：PARK TIME OFF 60S：PARK TIME ON, 60S 120S：PARK TIME ON, 120S 4.7.7 <running type> Choose the type of action that will take place on activation of Park: users can choose between: Preset, Tour or Pattern. Note: Time running available only if <idle time> and <running type> are both ON state. 4.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/provision-isr/pz-22ir/user-manual-english/page-31.html>PAGE 31</a></h6><p>CALL PRESET 1 TO RETURN CONFIRM. . . . . . SIZE Using up, down, left and right key to adjust the size of the mask, then call preset 1 to confirm and return. <remove current mask>: Remove current mask, then the black lump will disappear. <remove all mask>: Remove all mask, then all the black lump will disappear. 4.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/provision-isr/pz-22ir/user-manual-english/page-32.html>PAGE 32</a></h6><p>means alarm out on A side, ALoutB means alarm out on B side. Note: The alarm has highest priority. For example, if Cruise set to run at 12:00, and at the same time an alarm signal input, the dome camera would respond to the alarm first. <alarm in 1>: Set the alarm input and the dome’s corresponding action. Following options are applicable: [Off] or choose one function of <preset>, <tour>, <pattern>, and <auto>: when alarm.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/provision-isr/pz-22ir/user-manual-english/page-33.html>PAGE 33</a></h6><p>4.11 IR SET <main menu> <ir set> IR MODE: AUTO IR ZOOM SET 1: 006 IR ZOOM SET 2: 010 PRESENT LUX: 010 IR START SET: 006 IR CLOSE SET: 012 BACK EXIT <ir mode>: AUTO/OPEN/CLOSE <auto>: Default. When the detected signal value from the IR sensitive below the value of IR Start, the IR dome automatically open the IR lights. <open>: Open the IR lights forcibly (No influence from the detected signal value). <close>: Close the IR lights forcibly (No influence from the detected signal value).</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/provision-isr/pz-22ir/user-manual-english/page-34.html>PAGE 34</a></h6><p>APPENDIX I: DIP SWITCH SETTING DIP Switch consists of 8 numbers from 1-8, use 8421 binary cod, max 255 address. When the switch is in the “ON” position, the number from 1-8 corresponding to 1, 2, 4, 8, 32, 64, 128. For example, if you set 1, 3, 5, 7 switch to the “ON” position, the corresponding address will be 1+4+16+64=85, please refer to the blow details.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/provision-isr/pz-22ir/user-manual-english/page-35.html>PAGE 35</a></h6><p>1 1 0 0 0 1 0 0 36 0 0 1 0 0 1 0 0 37 1 0 1 0 0 1 0 0 38 0 1 1 0 0 1 0 0 39 1 1 1 0 0 1 0 0 40 0 0 0 1 0 1 0 0 41 1 0 0 1 0 1 0 0 42 0 1 0 1 0 1 0 0 43 1 1 0 1 0 1 0 0 44 0 0 1 1 0 1 0 0 45 1 0 1 1 0 1 0 0 46 0 1 1 1 0 1 0 0 47 1 1 1 1 0 1 0 0 48 0 0 0 0 1 1 0 0 49 1 0 0 0 1 1 0 0 50 0 1 0 0 1 1 0 0 51 1 1 0 0 1 1 0 0 52 0 0 1 0 1 1 0 0 53 1 0 1 0 1 1 0 0 54 0 1 1 0 1 1 0 0 55 1 1 1 0 1 1 0 0 0 0 0 1 1 1 0 0 57 1 0 0 1 1 1 0 0 58 0 1 0</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/provision-isr/pz-22ir/user-manual-english/page-36.html>PAGE 36</a></h6><p>89 1 0 0 1 1 0 1 0 90 0 1 0 1 1 0 1 0 91 0 0 1 1 1 0 1 0 92 0 0 1 1 1 0 1 0 93 1 0 1 1 1 0 1 0 94 0 1 1 1 1 0 1 0 95 1 1 1 1 1 0 1 0 96 0 0 0 0 0 1 1 0 97 1 0 0 0 0 1 1 0 98 0 1 0 0 0 1 1 0 99 1 1 0 0 0 1 1 0 100 0 0 1 0 0 1 1 0 101 1 0 1 0 0 1 1 0 102 0 1 1 0 0 1 1 0 103 1 1 1 0 0 1 1 0 104 0 0 0 1 0 1 1 0 105 1 0 0 1 0 1 1 0 106 0 1 0 1 0 1 1 0 107 1 1 0 1 0 1 1 0 108 0 0 1 1 0 1 1 0 109 1 0 1 1 0 1 1 0 110 0 1 1 1 0 1 1 0 111 1 1 1 1 0 1</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/provision-isr/pz-22ir/user-manual-english/page-37.html>PAGE 37</a></h6><p>143 1 1 1 1 0 0 0 1 144 0 0 0 0 1 0 0 1 145 1 0 0 0 1 0 0 1 146 0 1 0 0 1 0 0 1 147 1 1 0 0 1 0 0 1 148 0 0 1 0 1 0 0 1 149 1 0 1 0 1 0 0 1 150 0 1 1 0 1 0 0 1 151 1 1 1 0 1 0 0 1 152 0 0 0 1 1 0 0 1 153 1 0 0 1 1 0 0 1 154 0 1 0 1 1 0 0 1 155 1 1 0 1 1 0 0 1 156 0 0 1 1 1 0 0 1 157 1 0 1 1 1 0 0 1 158 0 1 1 1 1 0 0 1 159 1 1 1 1 1 0 0 1 160 0 0 0 0 0 1 0 1 161 1 0 0 0 0 1 0 1 162 0 1 0 0 0 1 0 1 163 1 1 0 0 0 1 0 1 164 0 0 1 0 0 1 0 1 165 1</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/provision-isr/pz-22ir/user-manual-english/page-38.html>PAGE 38</a></h6><p>197 1 0 1 0 0 0 1 1 198 0 1 1 0 0 0 1 1 199 1 1 1 0 0 0 1 1 200 0 0 0 1 0 0 1 1 201 1 0 0 1 0 0 1 1 202 0 1 0 1 0 0 1 1 203 1 1 0 1 0 0 1 1 204 0 0 1 1 0 0 1 1 205 1 0 1 1 0 0 1 1 206 0 1 1 1 0 0 1 1 207 1 1 1 1 0 0 1 1 208 0 0 0 0 1 0 1 1 209 1 0 0 0 1 0 1 1 210 0 1 0 0 1 0 1 1 211 1 1 0 0 1 0 1 1 212 0 0 1 0 1 0 1 1 213 1 0 1 0 1 0 1 1 214 0 1 1 0 1 0 1 1 215 1 1 1 0 1 0 1 1 216 0 0 0 1 1 0 1 1 217 1 0 0 1 1 0 1 1 218 0 1 0 1 1 0 1 1 219 1</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/provision-isr/pz-22ir/user-manual-english/page-39.html>PAGE 39</a></h6><p>APPENDIX II Shortcuts Key Chart Shortcut Key Function (Set Preset) Set #71 preset Proportional P/T OFF Set #73 preset 0S Park time ON Set #74 preset 60S Park time ON Set #75 preset 120S Park time ON Set #76 preset Dome restart Set #77 preset Restore Factory Setting Set #78 preset 360° scan and tour scan speed is automatic Set #79 preset 360° scan and tour scan speed is high, 20°/sec Set #80 preset 360° scan and tour scan speed is middle, 15°/sec Set #81 preset 360° scan and tour scan sp</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/provision-isr/pz-22ir/user-manual-english/page-40.html>PAGE 40</a></h6><p>Shortcut Key Function (Call Preset) Call #71 preset Proportional P/T ON Call #82 preset Start Cruise scan and switch the cruise scan direction Call #83 preset Delete all Presets Call #84 preset Start Pattern 1 Call #85 preset Start Pattern 2 Call #86 preset Start Pattern 3 Call #87 preset Start Pattern 4 Call #88 preset Call cruise 1 (default number 1~16 preset) Call #89 preset Call cruise 2 (default number 17~32 preset) Call #90 preset Call cruise 3 (default number 35~48 preset) Call</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/provision-isr/pz-22ir/user-manual-english/page-41.html>PAGE 41</a></h6><p>APPENDIX III Trouble Shooting Troubles No action when power on Reason Solution 1. The power supply is not 1. Correct the connection. connected correctly. 2. Check the power supply LED 2. The fuse is broken. power indicator. 3. Replace the fuse. 1. The dome DIP switch 1. Confirm DIP settings on camera Self-testing and image are setting is incorrect. power up screen. normal but the dome is out 2. RS485 cable is 2. Reset the DIP Switch according of control disconnected or reversed.</p></li><li><h6><a class="text-decoration-none text-link fw-bold" href=/manual/provision-isr/pz-22ir/user-manual-english/page-42.html>PAGE 42</a></h6><p></p></li></ul></nav></div></section></section></main><footer class=page-footer><div class="container flex-column py-3 py-sm-4"><div class="row mb-1 mb-sm-2 mb-md-5"><a href=/ class="brand offset-sm-0 col-sm-4 col-md-3 col-lg-2 offset-2 col-8 text-center text-md-start"><img class=logo-small src=/assets/img/brand-large.png alt=Manualshelf></a></div><div class=row><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Who We Are</dt><dd><a class=text-decoration-none href=/about>About Us</a></dd><dd><a class=text-decoration-none href=/company>Company</a></dd><dd><a class=text-decoration-none href=/careers>Careers</a></dd><dd><a class=text-decoration-none href=/terms>Terms & Privacy</a></dd></dl><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Resources</dt><dd><a class=text-decoration-none href=/brands>List of Manufacturers</a></dd><dd><a href=/ class=text-decoration-none>Support</a></dd><dd><a class=text-decoration-none href=/press>For the Press</a></dd><dd><a class=text-decoration-none href=/press#assets>Media assets</a></dd><dd><a class=text-decoration-none href=/faq>FAQ</a></dd></dl><dl class="text-center text-sm-start col-sm-3"><dt class=fw-bold>Get in touch</dt><dd><a class=text-decoration-none href=#>Blog</a></dd><dd><a class=text-decoration-none href=#>Email</a></dd><dd><a class=text-decoration-none href=/dmca>DMCA</a></dd></dl></div><div class=row><div class="text-center text-sm-start col-sm-4 pe-sm-0"><a href=https://www.facebook.com/pages/ManualShelf/1488826334681423 class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-facebook-f"></i></a><a href=https://www.twitter.com/ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-twitter"></i></a><a href=https://plus.google.com/+ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none me-2"><i class="fab fa-google-plus-g"></i></a><a href=http://www.pinterest.com/ManualShelf class="fs-5 text-center d-inline-block social rounded-2 align-middle text-decoration-none"><i class="fab fa-pinterest-p"></i></a></div><div class="col col-sm-8 d-flex flex-column align-items-center flex-sm-row flex-wrap flex-sm-nowrap justify-content-center justify-content-sm-end"><div class="copy w-auto d-flex align-items-center justify-content-center justify-content-sm-end mt-2 mt-sm-0 me-2">ManualShelf © 2013-2025</div><select class="form-select form-select-sm w-auto mt-2 mt-sm-0"><option value=usa>USA</option></select><div></div></div><div id=pixel><script>
googletag.cmd.push(function() { googletag.display('pixel'); });
</script></div></footer><script src=/assets/js/jquery-3.3.1.min.js></script><script src=/assets/js/bootstrap.bundle.min.js></script><script src=/assets/js/jquery.autocomplete.min.js></script><script type=text/javascript>
$.extend({
redirectPost: function(location, args) {
var form = '';
$.each(args, function(key, value) {
form += '<input type="hidden" name="' + key + '" value="' + value + '">';
});
form = '<form id="s1" action="' + location + '" method="POST">' + form + '</form>';
$(document.body).append(form);
$("#s1").submit();
}
});
$(document).ready(function(){
$("#query").autocomplete({
minChars: 3,
groupBy: 'type',
paramName: 'q',
dataType: 'json',
serviceUrl: '/autocomplete',
noCache: true,
showNoSuggestionNotice: true,
noSuggestionNotice: 'Zarro results found',
onSelect: function (suggestion) {
$.redirectPost(suggestion.data.url, {highlight: encodeURIComponent(JSON.stringify(suggestion.data.hls))});
}
});
var toc = $('.toc-selector');
if (toc.length) {
var slideParams = { duration: 800, easing: 'linear' };
toc.click(function() {
$(this).toggleClass('open');
var section = $('.toc-content');
var isCollapsed = section.attr('data-collapsed') === 'true';
if (isCollapsed) {
section.slideDown(slideParams)
section.attr('data-collapsed', 'false')
} else {
section.slideUp(slideParams);
section.attr('data-collapsed', 'true')
}
});
}
});
var lastSmall = $(window).width() < 576;
$(window).resize(function() {
var newSmall = $(window).width() < 576;
if (lastSmall != newSmall) {
lastSmall = newSmall;
window.location.href = window.location.href;
}
});
</script></body></html>
