User Manual
Table Of Contents
- Monitoring
- Commands
- Troubleshooting
- Command Line Interface (CLI)
- General Notes
- Command Line Interface (CLI) Variations
- CLI Command Types
- Using Tables and Strings
- Configuring the AP using CLI commands
- Log into the AP using HyperTerminal
- Log into the AP using Telnet
- Set Basic Configuration Parameters using CLI Commands
- Set System Name, Location and Contact Information
- Set Static IP Address for the AP
- Change Passwords
- Set Network Names for the Wireless Interface
- Enable 802.11d Support and Set the Country Code
- Enable and Configure TX Power Control for the Wireless Interface(s)
- Configure SSIDs (Network Names), VLANs, and Profiles
- Download an AP Configuration File from your TFTP Server
- Backup your AP Configuration File
- Set up Auto Configuration
- Other Network Settings
- Configure the AP as a DHCP Server
- Configure the DNS Client
- Configure DHCP Relay
- Configure DHCP Relay Servers
- Maintain Client Connections using Link Integrity
- Change Wireless Interface Settings
- Set Ethernet Speed and Transmission Mode
- Set Interface Management Services
- Configure Syslog
- Configure Intra BSS
- Configure Wireless Distribution System
- Configure MAC Access Control
- Set RADIUS Parameters
- Set Rogue Scan Parameters
- Set Hardware Configuration Reset Parameters
- Set VLAN/SSID Parameters
- Set Security Profile Parameters
- CLI Monitoring Parameters
- Parameter Tables
- CLI Batch File
- ASCII Character Chart
- Specifications
- Technical Services and Support
- Statement of Warranty
Command Line Interface (CLI) AP-4000/4000M/4900M User Guide
Configuring the AP using CLI commands
192
Enable and Configure TX Power Control for the Wireless Interface(s)
The TX Power Control feature lets the user configure the transmit power level of the card in the AP.
Perform the following commands to enable TX Power Control and set the transmit power level:
[Device-Name]>set txpowercontrol enable
[Device-Name]>set wif <interface number> currentbackofftpcvalue <0-9 dBm1-35 dBm>
Configure SSIDs (Network Names), VLANs, and Profiles
Perform the following command to configure SSIDs and VLANS, and to assign Security and RADIUS Profiles.
[Device-Name]>set wifssidtbl <Wireless Interface Index.SSID Index> ssid <Network Name>
vlanid <-1 to 1094> ssidauth <enable/disable> acctstatus <enable/disable> secprofile
<Security Profile Nmuber> radmacprofile <MAC Authentication Profile Name> radeapprofile
<EAP Authentication Profile Name> radacctprofile <Accounting Profile Name>
radmacauthstatus <enable/disable> aclstatus <enable/disable>
Examples:
[Device-Name]>set wifssidtbl 3.1 ssid accesspt1 vlanid 22 ssidauth enable acctstatus
enable secprofile 1 radmacprofile "MAC Authentication" radeapprofile "EAP Authentication"
radacctprofile "Accounting" radmacauthstatus enable aclstatus enable
[Device-Name]>set wifssidtbl 4.1 ssid accesspt1 vlanid 22 ssidauth enable acctstatus
enable secprofile 1 radmacprofile "MAC Authentication" radeapprofile "EAP Authentication"
radacctprofile "Accounting" radmacauthstatus enable aclstatus enable
Download an AP Configuration File from your TFTP Server
Start the Solarwinds TFTP program (available on the installation CD), and click on the Security tab to verify that the TFTP
server is configured to both transmit and receive files. (Note that TFTP programs other than Solarwinds may also require
this setting.) Then enter the following commands:
[Device-Name]>set tftpfilename <file name> tftpfiletype config
tftpipaddr <IP address of your TFTP server>
[Device-Name]>show tftp (to ensure the filename, file type, and the IP address are correct)
[Device-Name]>download *
[Device-Name]>reboot 0
After following the complete process (above) once, you can download a file of the same name (so long as all the other
parameters are the same), with the following command:
[Device-Name]>download *
Backup your AP Configuration File
Start the Solarwinds TFTP program (available on the installation CD), and click on the Security tab to verify that the TFTP
server is configured to both transmit and receive files. (Note that TFTP programs other than Solarwinds may also require
this setting.) Then enter the following commands:
[Device-Name]>upload <TFTP Server IP address> <tftpfilename (such as “config.sys”)> config
[Device-Name]>show tftp (to ensure the filename, file type, and the IP address are correct)
After setting the TFTP parameters, you can backup your current file (so long as all the other parameters are the same),
with the following command:
[Device-Name]>upload *