User's Manual
Table Of Contents
- Contents
- 1. Introduction
- Product Family
- System Requirements
- The Product Package
- 2. Cordless Networking With the Cordless Gateway
- Connectivity to an External Ethernet Device Which Provides High-Speed Internet Access
- Connectivity to an Ethernet Network
- Connectivity to an Ethernet Network Which Has High-Speed Internet Access
- Connectivity to a Network Server
- 3. Installing the Symphony Hardware
- Symphony-HRF Cordless Gateway
- LED Indicators
- Symphony Adapters
- Symphony PNP ISA Card
- Symphony PCI Card
- Symphony PC Card
- Symphony USB Adapter
- 4. Installing the Symphony Software
- 5. Symphony Composer Installation Wizard
- Step 1: Select a Security Code
- Step 2: Establish Communication With the Cordless Gateway
- Step 3: Configure TCP/IP Information
- Step 4: Assign a Computer Name
- Step 5: Select Drives and Printers to Share
- Step 6: Configure Switcher Prompt at Boot-up
- Step 7: Register Symphony Products
- 6. Symphony Maestro Configuration Tool
- Maestro Features for the Cordless Gateway
- Monitor the State of the Cordless Gateway
- Configure the Cordless Gateway to allow Internet Sharing
- Upgrade the Symphony-HRF Cordless Gateway
- Monitor the Cordless Gateway's Status
- Maestro Networking Features
- Obtain Network Status Information
- Test Cordless Connection
- Configure Network Parameters
- Remote Drive Sharing
- Maestro Administrative Features
- Determine Software Version in Use
- Register Products on Proxim's Web Site
- 7. Configuring a Cordless Gateway Network
- Cordless Gateway Configuration
- Configuring the Topology Parameter
- Configuring the ISP TCP/IP Settings
- Configuring the Internal TCP/IP Settings
- Cordless Gateway Client Configuration
- Configuration Examples
- A Cordless Gateway Connected Directly to a Device That Provides High-Speed Internet Access
- A Cordless Gateway Connected to a Wired Network That Does Not Have Shared Internet Access
- A Cordless Gateway Connected to a Wired Network That Has Shared Internet Access
- A Cordless Gateway Connected to a Network With a Server
- File Sharing
- Remote Drive Sharing
- Printer Sharing
- 8. Symphony Network Switcher
- Switching Between Network Profiles
- Editing a Network Profile
- Creating and Deleting Network Profiles
- Examples of When to Use Network Profiles
- 9. Adding a New Product to a Symphony
- Cordless Network
- Adding a New Computer to a Cordless Network
- Adding a Symphony-HRF Cordless Gateway to a Cordless Network
- 10. Upgrading Symphony Software
- Upgrading the Symphony-HRF Cordless Gateway's Firmware
- Method 1: Upgrade from the Symphony Web Site
- Method 2: Upgrade from Disk
- Upgrading a Symphony Adapter's Software
- 11. Uninstalling Symphony Software
- 12. Troubleshooting
- Frequently Asked Technical Support Questions
- Operational Issues
- General Questions
- A. 10BaseT Connector Specification
- B. Using Symphony With RangeLAN2 Cards
- C. Using the Symphony Driver for Windows NT
- Installing the Symphony Driver for Windows NT
- Uninstalling the Windows NT Driver
- D. Advanced Symphony Parameters
- Station Type
- Master Name
- Channel and Subchannel
- MAC Optimize
- Inactivity Timeout
- E. How to Reach Technical Support
- F. U.S. Specifications
- G. Regulatory Information
- Index
109
G. Regulatory Information
FCC WARNING
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particu-
lar installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
❑ Reorient or relocate the receiving antenna.
❑ Increase the separation between the equipment and the receiver.
❑ Connect the equipment into an outlet on a circuit different from
that which the receiver is connected.
❑ Consult the dealer or an experienced radio/TV technician for help.
Warning!
It is the responsibility of the users of the Symphony-HRF Cordless
Gateway to guarantee that the antennas are operated at least
one inch from any person. This is necessary to insure that the
product is operated in accordance with the RF Guidelines for
Human Exposure which have been adopted by the Federal
Communications Commission.