User's Manual
Table Of Contents
- Contents
- 1. Introduction
- Product Family
- System Requirements
- The Product Package
- 2. Cordless Networking With the Cordless Gateway
- Connectivity to an External Ethernet Device Which Provides High-Speed Internet Access
- Connectivity to an Ethernet Network
- Connectivity to an Ethernet Network Which Has High-Speed Internet Access
- Connectivity to a Network Server
- 3. Installing the Symphony Hardware
- Symphony-HRF Cordless Gateway
- LED Indicators
- Symphony Adapters
- Symphony PNP ISA Card
- Symphony PCI Card
- Symphony PC Card
- Symphony USB Adapter
- 4. Installing the Symphony Software
- 5. Symphony Composer Installation Wizard
- Step 1: Select a Security Code
- Step 2: Establish Communication With the Cordless Gateway
- Step 3: Configure TCP/IP Information
- Step 4: Assign a Computer Name
- Step 5: Select Drives and Printers to Share
- Step 6: Configure Switcher Prompt at Boot-up
- Step 7: Register Symphony Products
- 6. Symphony Maestro Configuration Tool
- Maestro Features for the Cordless Gateway
- Monitor the State of the Cordless Gateway
- Configure the Cordless Gateway to allow Internet Sharing
- Upgrade the Symphony-HRF Cordless Gateway
- Monitor the Cordless Gateway's Status
- Maestro Networking Features
- Obtain Network Status Information
- Test Cordless Connection
- Configure Network Parameters
- Remote Drive Sharing
- Maestro Administrative Features
- Determine Software Version in Use
- Register Products on Proxim's Web Site
- 7. Configuring a Cordless Gateway Network
- Cordless Gateway Configuration
- Configuring the Topology Parameter
- Configuring the ISP TCP/IP Settings
- Configuring the Internal TCP/IP Settings
- Cordless Gateway Client Configuration
- Configuration Examples
- A Cordless Gateway Connected Directly to a Device That Provides High-Speed Internet Access
- A Cordless Gateway Connected to a Wired Network That Does Not Have Shared Internet Access
- A Cordless Gateway Connected to a Wired Network That Has Shared Internet Access
- A Cordless Gateway Connected to a Network With a Server
- File Sharing
- Remote Drive Sharing
- Printer Sharing
- 8. Symphony Network Switcher
- Switching Between Network Profiles
- Editing a Network Profile
- Creating and Deleting Network Profiles
- Examples of When to Use Network Profiles
- 9. Adding a New Product to a Symphony
- Cordless Network
- Adding a New Computer to a Cordless Network
- Adding a Symphony-HRF Cordless Gateway to a Cordless Network
- 10. Upgrading Symphony Software
- Upgrading the Symphony-HRF Cordless Gateway's Firmware
- Method 1: Upgrade from the Symphony Web Site
- Method 2: Upgrade from Disk
- Upgrading a Symphony Adapter's Software
- 11. Uninstalling Symphony Software
- 12. Troubleshooting
- Frequently Asked Technical Support Questions
- Operational Issues
- General Questions
- A. 10BaseT Connector Specification
- B. Using Symphony With RangeLAN2 Cards
- C. Using the Symphony Driver for Windows NT
- Installing the Symphony Driver for Windows NT
- Uninstalling the Windows NT Driver
- D. Advanced Symphony Parameters
- Station Type
- Master Name
- Channel and Subchannel
- MAC Optimize
- Inactivity Timeout
- E. How to Reach Technical Support
- F. U.S. Specifications
- G. Regulatory Information
- Index
48
Address that the Cordless Gateway uses to communicate with the Internet or
an Ethernet network, see the section entitled “Configuring the ISP TCP/IP
Settings.” For information on the IP Address that the Cordless Gateway uses
to communicate with Symphony clients, see the section entitled “Configur-
ing the Internal TCP/IP Settings.”
The Cordless Gateway may be configured for two modes of operation: NAT
and Transparent Bridging. In addition, by default, the Cordless Gateway is
configured to perform both tasks simultaneously. This default setting should
work for many network configurations, but it may be changed within the
Symphony Maestro Configuration Tool. Click the <Configure> button
under the Symphony-HRF Cordless Gateway heading and choose the
Topology tab to change the device’s operating mode.
In the screen shot above, the first option refers to NAT mode only, the second
option refers to Transparent Bridging mode only, and the third option, which
is the default setting, corresponds to using both modes simultaneously.