User's Manual
Table Of Contents
- Contents
- 1. Introduction
- Product Family
- System Requirements
- The Product Package
- 2. Cordless Networking With the Cordless Gateway
- Connectivity to an External Ethernet Device Which Provides High-Speed Internet Access
- Connectivity to an Ethernet Network
- Connectivity to an Ethernet Network Which Has High-Speed Internet Access
- Connectivity to a Network Server
- 3. Installing the Symphony Hardware
- Symphony-HRF Cordless Gateway
- LED Indicators
- Symphony Adapters
- Symphony PNP ISA Card
- Symphony PCI Card
- Symphony PC Card
- Symphony USB Adapter
- 4. Installing the Symphony Software
- 5. Symphony Composer Installation Wizard
- Step 1: Select a Security Code
- Step 2: Establish Communication With the Cordless Gateway
- Step 3: Configure TCP/IP Information
- Step 4: Assign a Computer Name
- Step 5: Select Drives and Printers to Share
- Step 6: Configure Switcher Prompt at Boot-up
- Step 7: Register Symphony Products
- 6. Symphony Maestro Configuration Tool
- Maestro Features for the Cordless Gateway
- Monitor the State of the Cordless Gateway
- Configure the Cordless Gateway to allow Internet Sharing
- Upgrade the Symphony-HRF Cordless Gateway
- Monitor the Cordless Gateway's Status
- Maestro Networking Features
- Obtain Network Status Information
- Test Cordless Connection
- Configure Network Parameters
- Remote Drive Sharing
- Maestro Administrative Features
- Determine Software Version in Use
- Register Products on Proxim's Web Site
- 7. Configuring a Cordless Gateway Network
- Cordless Gateway Configuration
- Configuring the Topology Parameter
- Configuring the ISP TCP/IP Settings
- Configuring the Internal TCP/IP Settings
- Cordless Gateway Client Configuration
- Configuration Examples
- A Cordless Gateway Connected Directly to a Device That Provides High-Speed Internet Access
- A Cordless Gateway Connected to a Wired Network That Does Not Have Shared Internet Access
- A Cordless Gateway Connected to a Wired Network That Has Shared Internet Access
- A Cordless Gateway Connected to a Network With a Server
- File Sharing
- Remote Drive Sharing
- Printer Sharing
- 8. Symphony Network Switcher
- Switching Between Network Profiles
- Editing a Network Profile
- Creating and Deleting Network Profiles
- Examples of When to Use Network Profiles
- 9. Adding a New Product to a Symphony
- Cordless Network
- Adding a New Computer to a Cordless Network
- Adding a Symphony-HRF Cordless Gateway to a Cordless Network
- 10. Upgrading Symphony Software
- Upgrading the Symphony-HRF Cordless Gateway's Firmware
- Method 1: Upgrade from the Symphony Web Site
- Method 2: Upgrade from Disk
- Upgrading a Symphony Adapter's Software
- 11. Uninstalling Symphony Software
- 12. Troubleshooting
- Frequently Asked Technical Support Questions
- Operational Issues
- General Questions
- A. 10BaseT Connector Specification
- B. Using Symphony With RangeLAN2 Cards
- C. Using the Symphony Driver for Windows NT
- Installing the Symphony Driver for Windows NT
- Uninstalling the Windows NT Driver
- D. Advanced Symphony Parameters
- Station Type
- Master Name
- Channel and Subchannel
- MAC Optimize
- Inactivity Timeout
- E. How to Reach Technical Support
- F. U.S. Specifications
- G. Regulatory Information
- Index
52
Note:
The Cordless Gateway must be connected to the wired network
or to a device that provides high-speed Internet access (e.g., a
cable modem) during its boot-up cycle in order to obtain an IP
Address from a DHCP server. If you believe that the Cordless
Gateway should have received an IP Address from a DHCP server
but did not, try recycling power to the unit.
Configuring the Internal TCP/IP Settings
When configured to operate in NAT mode, the Cordless Gateway acts as a
DHCP server for Symphony-enabled computers on the network. By default, a
Cordless Gateway client is configured to accept a dynamic IP Address from a
DHCP server during the Symphony software installation. In addition, the
Cordless Gateway is assigned an IP Address that it uses to communicate with
the nodes on the cordless network.
By default, the Cordless Gateway is assigned an IP Address of 169.254.0.1
and a Subnet Mask of 255.255.0.0. In addition, the Cordless Gateway can
assign Symphony-enabled computers IP Addresses within the range
169.254.0.100 to 169.254.0.125, as shown below.