User's Manual
Table Of Contents
- Contents
- 1. Introduction
- Product Family
- System Requirements
- The Product Package
- 2. Cordless Networking With the Cordless Gateway
- Connectivity to an External Ethernet Device Which Provides High-Speed Internet Access
- Connectivity to an Ethernet Network
- Connectivity to an Ethernet Network Which Has High-Speed Internet Access
- Connectivity to a Network Server
- 3. Installing the Symphony Hardware
- Symphony-HRF Cordless Gateway
- LED Indicators
- Symphony Adapters
- Symphony PNP ISA Card
- Symphony PCI Card
- Symphony PC Card
- Symphony USB Adapter
- 4. Installing the Symphony Software
- 5. Symphony Composer Installation Wizard
- Step 1: Select a Security Code
- Step 2: Establish Communication With the Cordless Gateway
- Step 3: Configure TCP/IP Information
- Step 4: Assign a Computer Name
- Step 5: Select Drives and Printers to Share
- Step 6: Configure Switcher Prompt at Boot-up
- Step 7: Register Symphony Products
- 6. Symphony Maestro Configuration Tool
- Maestro Features for the Cordless Gateway
- Monitor the State of the Cordless Gateway
- Configure the Cordless Gateway to allow Internet Sharing
- Upgrade the Symphony-HRF Cordless Gateway
- Monitor the Cordless Gateway's Status
- Maestro Networking Features
- Obtain Network Status Information
- Test Cordless Connection
- Configure Network Parameters
- Remote Drive Sharing
- Maestro Administrative Features
- Determine Software Version in Use
- Register Products on Proxim's Web Site
- 7. Configuring a Cordless Gateway Network
- Cordless Gateway Configuration
- Configuring the Topology Parameter
- Configuring the ISP TCP/IP Settings
- Configuring the Internal TCP/IP Settings
- Cordless Gateway Client Configuration
- Configuration Examples
- A Cordless Gateway Connected Directly to a Device That Provides High-Speed Internet Access
- A Cordless Gateway Connected to a Wired Network That Does Not Have Shared Internet Access
- A Cordless Gateway Connected to a Wired Network That Has Shared Internet Access
- A Cordless Gateway Connected to a Network With a Server
- File Sharing
- Remote Drive Sharing
- Printer Sharing
- 8. Symphony Network Switcher
- Switching Between Network Profiles
- Editing a Network Profile
- Creating and Deleting Network Profiles
- Examples of When to Use Network Profiles
- 9. Adding a New Product to a Symphony
- Cordless Network
- Adding a New Computer to a Cordless Network
- Adding a Symphony-HRF Cordless Gateway to a Cordless Network
- 10. Upgrading Symphony Software
- Upgrading the Symphony-HRF Cordless Gateway's Firmware
- Method 1: Upgrade from the Symphony Web Site
- Method 2: Upgrade from Disk
- Upgrading a Symphony Adapter's Software
- 11. Uninstalling Symphony Software
- 12. Troubleshooting
- Frequently Asked Technical Support Questions
- Operational Issues
- General Questions
- A. 10BaseT Connector Specification
- B. Using Symphony With RangeLAN2 Cards
- C. Using the Symphony Driver for Windows NT
- Installing the Symphony Driver for Windows NT
- Uninstalling the Windows NT Driver
- D. Advanced Symphony Parameters
- Station Type
- Master Name
- Channel and Subchannel
- MAC Optimize
- Inactivity Timeout
- E. How to Reach Technical Support
- F. U.S. Specifications
- G. Regulatory Information
- Index
96
Enter a network User name and Password and click the <OK> button to log
onto the network. The Password may be left blank. You will be prompted to
confirm your Password before continuing.
5. The Symphony Composer Installation Wizard’s Welcome screen will now
appear. See Chapter 5 for additional information about this wizard. Among
other things, it will prompt you to enter the Security Code used by the
cordless network. Restart the computer if prompted.
The computer should now have access to the Symphony Cordless Network
and will act like any other Symphony-enabled computer on the network. To
revert to the RangeLAN2 configuration, simply change the Network Profile
from “Symphony” to “Original” from within the Symphony Switcher
configuration screen, by right-clicking the Switcher icon in the System Tray,
or by selecting the “Original” profile at the Switcher DOS prompt during
boot-up.
When you are ready to return to the Symphony Profile, simply use one of the
three methods above to switch the current profile. Refer to Chapter 8 for
more information on the Network Switcher and learn how to create and edit
Network Profiles.