User`s manual

ManualsBrandsProxima ManualsProjector6150

Extron • System 4

xixi

Switcher Series • User’s Manual • P/N 68-481-02 Rev. D

Configuration and ConnectionsProxima Installation

Page 1

SYSTEM 4

xixi

PROJECTOR COMMUNICATIONS KIT

ATTENTION!

PLEASE READ THIS DOCUMENT FOR IMPORTANT

INSTALLATION INSTRUCTIONS

THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:

Kit Type: PROXIMA

Included Communications Adapter(s):

Quantity Part Number Description

1 26-467-01 ADP, UNV, “A”

1 26-474-01 ADP, UNV, “F”

1 26-520-01 ADP, UNV, “M”

1 26-523-01 ADP, UNV, “N”

THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING

COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURER’S VARIOUS

MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS

INDICATED BY THE “✔” IN THE “CONFIG AS” COLUMN. IF YOUR PROJECTOR MODEL

DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER

WITH THE CORRECT SETTINGS.

PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND

SIGNAL CONNECTION INSTRUCTIONS.

THIS SWITCHER HAS BEEN CONFIGURED FOR: PROXIMA Pro AV 9310/9320/

9400, DP9250

CONFIG MODEL SW1 SW2 SW3 SW4 SW5 SW6 PROJ COMM

AS 1 2 3 4 CABLE ADAPTER

✔ Proxima Pro AV off on off on 0 0 C F 0 J15 26-467-01

9320/9400

✔ Proxima Pro AV 9310 off on off on 0 0 C F 0 J15 26-467-01

✔ Proxima DP9250 off on off on 0 0 C F 0 J15 26-474-01

Proxima 6850 off on off on 0 0 C E 0 J15 26-520-01

Proxima 6150 off on off on 0 0 F E 0 J15 26-523-01

Summary of content (9 pages)

PAGE 1
Proxima Installation Configuration and Connections xi SYSTEM 4xi PROJECTOR COMMUNICATIONS KIT ATTENTION! PLEASE READ THIS DOCUMENT FOR IMPORTANT INSTALLATION INSTRUCTIONS THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS: Kit Type: PROXIMA Included Communications Adapter(s): Quantity 1 1 1 1 Part Number 26-467-01 26-474-01 26-520-01 26-523-01 Description ADP, UNV, “A” ADP, UNV, “F” ADP, UNV, “M” ADP, UNV, “N” THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING COMMUNICATIONS A
PAGE 2
Proxima Installation Configuration and Connections xi to Proxima Pro AV 9310/9320/9400 Connecting System 4xi If the System 4xi is already configured for a Proxima projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct configuration. 1. Use the Front Panel to display the Information Menu to verify that the System 4xi is already set up for the Proxima.
PAGE 3
Proxima Installation Configuration and Connections 5. The Proxima Comm Adapter has a 9-pin male connector that accommodates the Comm Extension cable. The other end of the Comm Adapter plugs into the projector’s RS-232C port. 6. Plug the 15-pin HD connector of the Projector Communications Extension cable into the PJ Comm port on the System 4xi. ______ Secure all of the connector screws. 7.
PAGE 4
Proxima Installation Configuration and Connections xi to Proxima DP9250 Connecting System 4xi If the System 4xi is already configured for a Proxima DP9250 projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct configuration. 1. Use the Front Panel to display the Information Menu to verify that the System 4xi is already set up for the Proxima.
PAGE 5
Proxima Installation Configuration and Connections 5. Connect the Proxima DIN adapter to the projector’s “PC Control 2” port. Next, connect the Comm Adapter’s 9-pin male connector to the 9-pin female end of the Proxima DIN connector. 6. Plug the 15-pin HD connector of the Projector Communications Extension cable into the PJ Comm port on the System 4xi. ______ Secure all of the connector screws. 7.
PAGE 6
Proxima Installation Configuration and Connections xi to Proxima 6850 Connecting System 4xi If the System 4xi is already configured for a Proxima 6850 projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct configuration. 1. Use the Front Panel to display the Information Menu to verify that the System 4xi is already set up for the Proxima.
PAGE 7
Proxima Installation Configuration and Connections 5. Connect the Comm adapter’s 15-pin female connector to the 15-pin male “Control” connector on the rear panel of the projector. Next, connect the Comm adapter’s 9-pin male connector to the 9-pin female end of the Projector Communications Extension cable. 6. Plug the 15-pin HD connector of the Projector Communications Extension cable into the PJ Comm port on the System 4xi. ______ Secure all of the connector screws. 7.
PAGE 8
Proxima Installation Configuration and Connections xi to Proxima 6150 Connecting System 4xi If the System 4xi is already configured for a Proxima 6150 projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4xi ’s Main Controller Board. Begin at Step 1 to verify the correct configuration. 1. Use the Front Panel to display the Information Menu to verify that the System 4xi is already set up for the Proxima.
PAGE 9
Proxima Installation Configuration and Connections 6. Plug the extension cable’s 15-pin HD male connector to the PJ Comm port on the System 4xi. ______ Secure all of the connector screws. 7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV cable onto the System 4xi output. Connect the other end onto the 15-pin “Analog Computer VGA” connector of the projector.