User's Manual

ManualsBrandsPS TEC ManualsElectronicsAutonomous Counter

AUTONOMOUS COUNTER (POWERED TYPE) USER MANUAL [PSM-NGC-P01]

1. Summary

The autonomous digital shot counter (powered type) (PSM-NGC-P01) uses a low-power 16-bit microcontroller and a low-

power 2.4GHz wireless communication chip (IEEE 802.15.4 / BLE5) and can use external power (5V).

This product is installed in production facilities, the measured production information is transmitted to the gateway (TERMINAL)

using wireless communication, can receive specific information (time, set value, etc.) from the gateway (TERMINAL).

2. Module block diagram

■ MCU(MSP430FR692x)

- Control acceleration sensor and magnetic sensor and read data.

- The data collected on the sensor is displayed on the LCD.

- Display data on LCD according to Button input and communicate with BLE5 Chip.

■ BLE Chip(nRF52840)

- The data received from the MCU is transmitted by wireless communication (IEEE 802.15.4 / BLE5).

- Transmit the data received by wireless communication to MCU.

■ 3.6V BAT

- Supply power to MCU and BLE5 Chip.

■ 5V External Power

- Supply power to MCU and BLE5 Chip through the regulator.

■ Button

- User commands are sent to the MCU.

■ Acceleration sensor, magnetic sensor

- The measured data is transferred to the MCU.

Button

Chip

ANT.

LCD

3.6V

BAT

Magnetic

Sensor

Acceleration

sensor

X-TAL

32.768KHz

X-TAL

32.768KHz

X-TAL

32MHz

Regulator

EXT.

3.6V

Summary of content (6 pages)

PAGE 1
AUTONOMOUS COUNTER (POWERED TYPE) USER MANUAL [PSM-NGC-P01] 1. Summary The autonomous digital shot counter (powered type) (PSM-NGC-P01) uses a low-power 16-bit microcontroller and a lowpower 2.4GHz wireless communication chip (IEEE 802.15.4 / BLE5) and can use external power (5V). This product is installed in production facilities, the measured production information is transmitted to the gateway (TERMINAL) using wireless communication, can receive specific information (time, set value, etc.
PAGE 2
AUTONOMOUS COUNTER (POWERED TYPE) USER MANUAL [PSM-NGC-P01] 3. Appearance and part names ① ② ③ ④ ⑤ ⑥ ⑦ Magnetic bracket Sensor part LCD display Button. Hole to fix the product. QR code (product number) External power terminal 4. Size [Magnetic bracket] [Product] 5. Composition of LCD display ① ② ③ ④ ⑤ ⑥ Operation status Communication status (RF) Battery status Attached state External power input Cumulative shot and set value display 6.
PAGE 3
AUTONOMOUS COUNTER (POWERED TYPE) USER MANUAL [PSM-NGC-P01] ② Hardware specifications  16bit MCU  256Kbit FRAM  2.4GHz BLE5 ③ Rating -25 ~ 80 ℃ Quality guarantee 24 times / day Battery life 0.2 ~ 300 sec / Press 2 ~ 300 sec / Injection Size (mm) Usable temp. Comm.
PAGE 4
AUTONOMOUS COUNTER (POWERED TYPE) USER MANUAL [PSM-NGC-P01] ⑦ Communication status – Received signal strength indication (RSSI)  Display for 3 seconds during manual communication (Manual communication: Press the button for 3 seconds in the cumulative shot display mode)  Display status When communication is successful, the LCD displays as follows. 7.
PAGE 5
AUTONOMOUS COUNTER (POWERED TYPE) USER MANUAL [PSM-NGC-P01] < FCC Compliance Statement > FCC ID: 2AVSN-PSM-NGC-P01 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interferencethat may cause undesired operation.
PAGE 6
FCC Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.