ALPHA AM3 OWNER’S GUIDE www.psbspeakers.
IMPORTANT SAFETY INSTRUCTIONS FCC Warnings 1. Read these instructions. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7.
Operating Environment Temperature This product is designed to operate within a temperature range of 0 - 35 degrees Celsius only. CAUTION Risk of explosion if the battery is replaced by an incorrect type. Notes on environmental protection At the end of its useful life, this product must not be disposed of with regular household waste but must be returned to a collection point for the recycling of electrical and electronic equipment. The symbol on the product, user’s manual and packaging, point this out.
Front of the Amplified Speaker Status Light Remote Sensor Status Light: Displays different colours to show: Control Dial: Turn: Press: Control Dial - which source is playing - a listening mode is chosen - maximum and minimum volume, bass and treble controls - Bluetooth pairing mode to adjust the volume to change the input Remote Sensor: Point the remote control at the remote sensor and press the buttons.
Back Panel of the Amplified Speaker 2 1 3 4 9 AM3 Power Adapter Model: WTB65-1903150-T 19V 3.15A 8 5 6 7 1) Analogue Input (Auxiliary) Using the supplied 1/8” (3.5mm) connection cable, connect one end to the speaker AUX input, and the opposite end to the selected audio source. Cyan status light. 2) Phono Input Using RCA cables, connect one end to the phono input. Connect the phono ground cable. Green status light.
Remote Control Power On/Off Bluetooth Interrupt Volume Control Mute Input Selection Input Selection Subwoofer ON/OFF Treble Control SUB MODE Sound Mode Selection TREBLE BASS Bass Control Install the supplied two AAA batteries into the remote control. Be careful to ensure that it is correctly inserted according to the polarity (+/-). You should only use the battery specified for this system.
. Bass Control: Controls the amount of bass for your listening preference. When initially activated, the bass will be set to neutral, or halfway in the range. 8. Treble Control: Controls the amount of treble for your listening preference. When initially activated, the bass will be set to neutral, or halfway in the range. Note: When adjusting the Bass or Treble the status light will make a single red flash to show that the midpoint of the level has been reached.
How to Pair with a Bluetooth-Enabled Device I. Using the input selections buttons on the remote control, toggle between sources and switch to the BT input (Blue). LED will flash blue-red for two minutes while in Discovery Mode. II. Open the Bluetooth settings on your mobile device and start searching for the unique device ID of the AM3. III. Once paired, the LED will be illuminated solid Blue to indicate a successful pairing. Start playback of Bluetooth device upon successful pairing. IV.
Positioning I. As symmetrically as possible, place your Alpha AM3 Powered Speakers at a comfortable listening location with no obstructions at the front or back. II. We recommend at least three inches of clearance around the back of both speakers. Good air circulation is required for heat dissipation, and to ensure proper performance of the rear-firing ports. Similar positioning and clearance should be used for both speakers. For more detailed information about speaker placement, please visit www.
Specifications FREQUENCY RESPONSE On Axis @ 0° ± 3dB LF Cutoff -10dB 56Hz-20Khz 40Hz AMPLIFIER POWER 35 watts x 2 RMS ACOUSTIC DESIGN Tweeter (Nominal) 3/4” (19mm) Aluminium Dome with Ferrofluid and Neodymium Magnet Woofer (Nominal) 4” (100mm) Cone Rubber Surround Steel Basket INPUTS Analog Digital Wireless Design Type 3.
20-066 AM3 Owner’s Manual
