User manual

ManualsBrandsPsion Teklogix ManualsGadgets7535 G2

7535 G2

Hand-Held Computer

User Manual

August 11, 2009 P/N 8000075.E

ISO 9001 Certified

Quality Management System

Summary of content (372 pages)

PAGE 1
7535 G2 Hand-Held Computer User Manual August 11, 2009 ISO 9001 Certified Quality Management System P/N 8000075.
PAGE 2
© Copyright 2009 by Psion Teklogix Inc. 2100 Meadowvale Boulevard, Mississauga, Ontario, Canada L5N 7J9 http://www.psionteklogix.com This document and the information it contains is the property of Psion Teklogix Inc., is issued in strict confidence, and is not to be reproduced or copied, in whole or in part, except for the sole purpose of promoting the sale of Psion Teklogix manufactured goods and services.
PAGE 3
Return-To-Factory Warranty Psion Teklogix Inc. provides a return to factory warranty on this product for a period of twelve (12) months in accordance with the Statement of Limited Warranty and Limitation of Liability provided at: www.psionteklogix.com/warranty The warranty on Psion Teklogix manufactured equipment does not extend to any product that has been tampered with, altered, or repaired by any person other than an employee of an authorized Psion Teklogix service organization.
PAGE 4
Restriction On Hazardous Substances (RoHS) Directive 2002/95/EC What is RoHS? The European Union has mandated that high environmental standards be met in the design and manufacture of electronic and electrical products sold in Europe, to reduce hazardous substances from entering the environment. The “Restriction on Hazardous Substances Directive (RoHS)” prescribes the maximum trace levels of lead, cadmium, mercury, hexavalent chromium, and flame retardants PBB and PBDE that may be contained in a product.
PAGE 5
TABLE OF CONTENTS Program License Agreements . . . . . . . . . . . . . . . . . . . . . . . . . . xiii Approvals And Safety Summary . . . . . . . . . . . . . . . . . . . . . . . . . xix Chapter 1: Introduction 1.1 1.2 1.3 1.4 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Text Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 6
Contents 2.7.3 2.8 2.9 Using The SCU To Connect To The WLAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 2.7.3.1 SSID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 2.7.3.2 EAP Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 2.7.3.3 Encryption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 7
Contents 3.4.3 3.5 3.6 3.7 3.8 3.9 Audio Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 3.4.3.1 Adjusting The Beeper Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Internal Scanners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 3.5.1 Scanning Techniques . . . . . . . . . .
PAGE 8
Contents Chapter 5: Configuration 5.1 5.2 5.3 5.4 5.5 5.6 iv Remote Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 The TekTerm Application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Pocket PC Compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 9
Contents 5.7 5.6.9.2 Sound Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 Bluetooth Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126 5.7.1 Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .127 5.7.2 Headset . . . . . . . . . . . . . . . . . .
PAGE 10
Contents 5.12.1 Formatting A Memory Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158 5.12.2 Creating Partitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .159 5.12.3 Partition Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .160 5.13 Teklogix Error Handling Service. . . . . . . . . . . . . . . . .
PAGE 11
Contents 6.6 6.7 6.5.5.4 Power LED Does Not Light Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184 6.5.5.5 Indicator Does Not Light When Battery Installed. . . . . . . . . . . . . . . . . . . .184 Combo Charger. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .184 6.6.1 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 12
Contents Chapter 7: Specifications 7.1 7535 G2 Hand-Held Computer Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .201 7.1.1 Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .201 7.1.2 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .203 7.1.3 Approvals . . . . . .
PAGE 13
Contents B.1.5 Global . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10 Appendix C: Bar Code Settings C.1 C.2 C.3 Bar Code Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .C-5 C.1.1 Scanner Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 14
Contents C.4 x C.3.12 MSI Plessey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-35 C.3.13 Code 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-36 C.3.14 Interleaved 2 of 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-36 C.3.15 Matrix 2 of 5 . . . . . .
PAGE 15
Contents C.5 C.4.27 Postal: Canadian. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-54 Non-Decoded Scanners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-55 C.5.1 Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-56 C.5.2 Code 39 . . . . . . . . . . . . .
PAGE 16
Contents D.5 D.4.7 Configuring The Bar Code Decoding Symbologies . . . . . . . . . . . . . . . . . . . . . . . . . . D-13 D.4.8 Setting The Active Preset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-14 D.4.9 Viewing A Preset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-14 D.4.10 Creating A Custom Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 17
PROGRAM LICENSE AGREEMENTS Microsoft's End User License Agreement You have acquired a device (“DEVICE”) that includes software licensed by Psion Teklogix Inc. from Microsoft Licensing Inc. or its affiliates (‘MS”). Those installed software products of MS origin, as well as associated media, printed materials, and “online” or electronic documentation (“SOFTWARE”) are protected by international intellectual property laws and treaties. The SOFTWARE is licensed, not sold. All rights reserved.
PAGE 18
Chapter : Program License Agreements • • • • • Note on Java Support. The SOFTWARE may contain support for programs written in Java.
PAGE 19
Chapter : Program License Agreements The Software is the property of Psion Teklogix Inc. or its licensors and is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties. The Software is licensed, not sold. Psion Teklogix Inc. provides the Software and licenses its use worldwide. You assume responsibility for the selection of the Software to achieve your intended results, and for the use and results obtained from it. 1.
PAGE 20
Chapter : Program License Agreements g. Assignment. You may not assign or transfer the Software to a third party or allow a third party to use the same. h. Reverse Engineering. Modification, reverse engineering, reverse compiling, disassembly, unbundling or extraction of the Software is expressly prohibited. i. Export Restrictions.
PAGE 21
Chapter : Program License Agreements Under no circumstances are we or our third party suppliers liable for damages of third parties claimed against you, or for harm to your records or data, or special, incidental, indirect, or consequential damages, including but not limited to lost profits, lost business revenue or failure to realize expected savings, loss of data, loss of use of the Software or any associated equipment, downtime and user’s time, even if you informed us of their possibility, or for breach
PAGE 22
Chapter : Program License Agreements performance or to exercise a right when entitled, does not prevent us from doing so at a later time, either in relation to that default or any subsequent one. No modifications of this Agreement shall be effective unless in writing and approved by us.
PAGE 23
APPROVALS AND SAFETY SUMMARY FCC DECLARATION OF CONFORMITY (DOC) Applicant’s Name & Address: PSION TEKLOGIX INC. 2100 Meadowvale Blvd. Mississauga, Ontario Canada L5N 7J9 Tel: (905) 813-9900 US Representative’s Name & Address: PSION TEKLOGIX CORP. 1810 Airport Exchange Blvd., Suite 500 Erlanger, KY, 41018, USA Tel: (859) 372-4329 Equipment Type/Environment: Computing Devices Trade Name / Model No.
PAGE 24
Chapter : Approvals And Safety Summary CE Marking When used in a residential, commercial or light industrial environment the product and its approved UK and European peripherals fulfil all requirements for CE marking. R&TTE Directive 1999/5/EC This equipment complies with the essential requirements of EU Directive 1999/5/EC (Declaration available: www.psionteklogix.com). Cet équipement est conforme aux principales caractéristiques définies dans la Directive européenne RTTE 1999/5/CE.
PAGE 25
Chapter : Approvals And Safety Summary Psion Teklogix tímto prohlašuje, že 7535 G2 je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1995/5/ES (NV č. 426/2000 Sb.) a Prohlášení o shodě je k dispozici na www.psionteklogix.com. Toto zarízení lze provozovat v České republice na základě generální licence č. GL-12/R/2000. Psion Teklogix týmto vyhlasuje, že 7535 G2 spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1995/5/ES (NV č. 443/2001 Z.z.
PAGE 26
Chapter : Approvals And Safety Summary FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. Important: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment under 47 CFR 2.1093 paragraph (d)(2), for use in a PDA. End users must follow the specific operating instructions for satisfying RF exposure compliance.
PAGE 27
Chapter : Approvals And Safety Summary Warnings To Users This product is a Class I/Class II laser product according to CDRH 21 CFR 1040.10 and 1040.11 and Class1/Class 2 laser product according to IEC 60825-1 Ed. 2.0. The SE1200 ALR has an maximum radiated power less than 1.4 mW; according to EN 60825-1: 2001 it is classified as a Class 3B laser product. Laser Warnings Important: For your own safety, it is critical that you comply with the following warnings.
PAGE 28
Chapter : Approvals And Safety Summary • • Danger of explosion if a 7535 G2 battery is incorrectly handled, charged, disposed of or replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the instructions described in “Lithium-ion Battery Safety Precautions”, below. Carefully review all battery safety issues.
PAGE 29
Chapter : Approvals And Safety Summary • • • • • • When charging, use the battery charger specifically designed for the battery. Do not pierce, strike, throw or step on the battery. Do not directly solder the battery. Do not connect the battery to an electrical outlet, vehicle cigarette lighter, etc. Do not put battery into a microwave oven or pressurized container. Do not use the battery in combination with primary batteries (such as dry-cell batteries) or batteries of different capacities or brands.
PAGE 30
Chapter : Approvals And Safety Summary • • • • • • • • Use of an attachment not recommended or sold by the battery charger or AC/DC adaptor manufacturer may result in fire, electric shock, or personal injury. To reduce risk of damage to the electric plug and cord when unplugging the charger or AC/DC adaptor, pull the plug rather than the cord. Make sure the cord is positioned so that it is not stepped on, tripped over, or otherwise subjected to damage or stress.
PAGE 31
INTRODUCTION 1 1.1 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2 Text Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.3 7535 G2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.4 About The 7535 G2 Hand-Held Computer . . . . . . . . . . . . . . . . . . . . . . . 7 1.4.1 The 7535 G2 Hand-Held Computer . . . . . . . . . . . . . . . . . . . . . . 8 1.4.2 Regulatory Labels . . . . .
PAGE 32
2 Psion Teklogix 7535 G2 Hand-Held Computer User Manual
PAGE 33
Chapter 1: Introduction About This Manual 1.1 About This Manual This manual describes how to configure, operate, and maintain the Psion Teklogix 7535 G2 Hand-held Computer. Chapter 1: Introduction provides a basic overview of the 7535 G2 computer. Chapter 2: Basic Checkout describes preparing the 7535 G2 ready for operation, including setting up your radio.
PAGE 34
Chapter 1: Introduction Text Conventions 1.2 Text Conventions Note: Notes highlight additional helpful information. Important: These statements provide particularly important instructions or additional information that is critical to the operation of the equipment. Warning: These statements provide critical information that may prevent physical injury, equipment damage or data loss. 1.3 7535 G2 Features Rugged design: • • Fully-sealed enclosure (rated to IP65).
PAGE 35
Chapter 1: Introduction 7535 G2 Features • • IEEE 802.11a/b/g Compact Flash Radio with integrated antenna, operating in 2.4 GHz and 5 GHz bands Bluetooth® radio 2.4 GHz (10 m range) Application software: • • • • Internet Explorer for Windows CE Optimized for use with Open TekTerm (for details, see the TekTerm Software User Manual, P/N 8000073) Wordpad ActiveSync Display: • • • • • • • 320 x 240 (1/4 VGA) graphic colour TFT 8.9 cm (3.5 in.
PAGE 36
Chapter 1: Introduction 7535 G2 Features Indicators and controls: • • Beeper with volume control LEDs for radio transmit and receive, scanning, battery status, and user applications Bar code applications: • • • • Internal 1D & 2D scan engines: standard, long range, advanced long range, enhanced standard range Fuzzy logic internal scan engine Internal 1.
PAGE 37
Chapter 1: Introduction About The 7535 G2 Hand-Held Computer • • System backup during battery swap (up to 20 minutes) One week real-time clock backup Network Management: • • • • 1.4 SNMP MIB 2 support Remote software download Remote WLAN management Enhanced security for 802.11 About The 7535 G2 Hand-Held Computer The 7535 G2 is a ruggedized hand-held personal computer, running the Microsoft Windows CE 5.0 operating system.
PAGE 38
Chapter 1: Introduction The 7535 G2 Hand-Held Computer 1.4.1 The 7535 G2 Hand-Held Computer Figure 1.1 7535 G2 With 58-Key Keyboard Figure 1.
PAGE 39
Chapter 1: Introduction The 7535 G2 Hand-Held Computer Figure 1.3 Tether Port Figure 1.
PAGE 40
Chapter 1: Introduction Regulatory Labels 1.4.2 Regulatory Labels Figure 1.5 Laser Warning Label This label is affixed below the scanner window. Warning: Using controls or adjustments or performing procedures other than those specified herein may result in hazardous radiation exposure. Figure 1.6 LED Radiation Notice Label This label is affixed below the scanner window.
PAGE 41
2 BASIC CHECKOUT 2.1 Features Of The 7535 G2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2.2 Preparing The 7535 G2 For Operation . . . . . . . . . . . . . . . 2.2.1 Equipment You Need To Get Started. . . . . . . . . . . 2.3 Powering Up The 7535 G2 . . . . . . . . . . . . . . . . . . . . . 2.3.1 Charging The Battery. . . . . . . . . . . . . . . . . . . 2.3.2 Installing The Battery And Switching The Computer On 2.4 Attaching Carrying Accessories . . . . . . . . . . . . . . . . . . 2.4.
PAGE 42
2.11 Resetting The 7535 G2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 43
Chapter 2: Basic Checkout Features Of The 7535 G2 2.1 Features Of The 7535 G2 Figure 2.1 Front Of 7535 G2 7535 G2 Screen Sound Port Ambient Light Sensor Tether Port Docking Port Figure 2.
PAGE 44
Chapter 2: Basic Checkout Preparing The 7535 G2 For Operation 2.2 Preparing The 7535 G2 For Operation Typically, 7535 G2 Hand-Held Computers are configured at the factory and arrive ready for use. Although these computers are equipped with an internal Compact Flash and SD I/O slot, these slots are not intended for user modification. If a device needs to be changed or added in these slots, contact qualified Psion Teklogix personnel. 2.2.
PAGE 45
Chapter 2: Basic Checkout Installing The Battery And Switching The Computer On Important: The 7535 G2 battery properties dialog box (see “Battery Capacity” on page 119) may indicate an incorrect battery capacity until the new battery has been fully charged. It may take several charge/discharge cycles for the battery capacity gauge to register capacity with the full 95% accuracy. 2.3.2 Installing The Battery And Switching The Computer On Important: Always switch the unit off before changing the battery.
PAGE 46
Chapter 2: Basic Checkout Attaching Carrying Accessories To switch the unit on: • Press and hold down the [ENTER/ON] key for at least one second. • When all four LEDs flash yellow, release the [ENTER/ON] button. A splash screen displaying the Psion Teklogix logo and the Windows CE logo appears. When Windows CE has successfully loaded, the startup desktop is displayed. Note: The screen may go blank for a few seconds after the splash screen loading bar reaches the end.
PAGE 47
Chapter 2: Basic Checkout Attaching The Hand Strap Figure 2.4 Attaching The Hand Strap • Stretch the handstrap toward the base of the 7535 G2, and hook the bottom of the handstrap into the slot near the base of the battery pack. Figure 2.
PAGE 48
Chapter 2: Basic Checkout Attaching The Pistol Grip 2.4.2 Attaching The Pistol Grip Note: A Phillips head screwdriver is required. The pistol grip is attached to the back of the 7535 G2 using the four threaded inserts in the upper part of the 7535 G2 casing. Four black #4-40 Phillips head screws are provided with this accessory. Note: Prior to installation, make sure the trigger mechanism is securely snapped into the pistol grip body and that the trigger operates properly.
PAGE 49
Chapter 2: Basic Checkout Calibrating The Touchscreen 2.5 Calibrating The Touchscreen Note: Keep in mind that 7535 G2 Hand-Held Computers can be ordered with or without touchscreens, and that the touchscreen function can be turned off (see “Touch” on page 125). If you have the 7535 G2 touchscreen feature, it is factory-calibrated and ready-to-go; however, over time the touchscreen's operating parameters may change, and it may need to be recalibrated for correct operation.
PAGE 50
Chapter 2: Basic Checkout Configuring An IEEE 802.11 Radio In The Unit To configure the 802.11 radio: 1. Tap on Start>Settings>Network and Dial-up Connections. (If the Start Menu isn’t displayed in the taskbar, press [BLUE] [0] to display it.) If you’re using the keyboard, press [BLUE] [0] to display the Start Menu. Use the [DOWN] arrow key to highlight Settings. Press the [RIGHT] arrow key to display the sub-menu. Highlight Network, and press [ENTER]. Figure 2.7 Network And Dial-Up Connections 2.
PAGE 51
Chapter 2: Basic Checkout Configuring An IEEE 802.11 Radio In The Unit 3. Wireless Statistics Tab When you choose the Wireless LAN icon, an 802.11 Wireless LAN Settings window (PTXCF8385P N1 in the sample below) is displayed. This tab lists your radio statistics. Choosing the Zero button resets the statistics of the last four items: Packets IN, Packets OUT, IN errors and OUT errors. • Display the next tab in this window, Wireless Information. 4.
PAGE 52
Chapter 2: Basic Checkout Configuring An IEEE 802.11 Radio In The Unit This tab lists available networks—any access points that are broadcasting an SSID, and it lists preferred networks—networks that you have configured. Since access points are generally secure, they will most likely not be listed here. By default, 7535 G2 attempts to connect to preferred networks.
PAGE 53
Chapter 2: Basic Checkout Configuring An IEEE 802.11 Radio In The Unit Important: Keep in mind that the 7535 G2 will only communicate with access points that are configured with the same SSID. Ad Hoc And Infrastructure If you are using an Infrastructure network—one in which 7535 G2s must pass data through an access point—leave the checkbox next to This is an ad hoc network blank.
PAGE 54
Chapter 2: Basic Checkout Configuring An IEEE 802.11 Radio In The Unit Network Key This text box is used to specify a 5 or 13 ASCII character sequence or an equivalent 10 or 26 Hexadecimal digit sequence that matches the active WEP key on the access point. • To assign a Network key, highlight The key is provided automatically, and uncheck the checkbox to disable this option. Figure 2.9 Accessing Network Key And Key Index Disable this option to access Network Key & Key Index fields.
PAGE 55
Chapter 2: Basic Checkout Assigning An IP Address Saving and exiting the radio setup. Once you have completed the configuration, press [ENTER] or tap on OK. The connection you created will be listed in the Wireless Information tab as a preferred network. The radio will search for the SSID and will compare the WEP and authentication information you specified.
PAGE 56
Chapter 2: Basic Checkout Name Servers Tab Figure 2.10 Defining An IP Address • Tap the stylus on the radio button next to Specify an IP address to select it. • Type an IP, Subnet Mask and Default Gateway address in the appropriate fields. Press [ENTER] to save your information. 2.7.2 Name Servers Tab Note: If DHCP is enabled, name server addresses are assigned automatically. • In the PTXCF8385P N1 Settings window, display the IP Information tab. • In the IP Information tab, tap on the Configure button.
PAGE 57
Chapter 2: Basic Checkout Advanced Features The DNS and WINS fields in the Name Servers tab allow you to specify additional WINS and DNS resolvers. The format for these fields is ###.###.###.###. 2.7.3 Advanced Features To display the Advanced Wireless Settings dialog box: • Tap the Advanced button in the Wireless Information tab. This window lists the available preferred networks. 2.7.3.
PAGE 58
Chapter 2: Basic Checkout Summit Client Utility (SCU) For RA2041 802.11b/g Radio 2.7.3.3 Changing Network Properties To change the properties of an existing preferred network: • Highlight the network that you want to modify. • Tap on the Properties button. • Make any necessary changes in the Wireless Properties dialog box, and press [ENTER] to save the changes. 2.8 Summit Client Utility (SCU) For RA2041 802.11b/g Radio This section describes the Summit Client Utility (SCU).
PAGE 59
Chapter 2: Basic Checkout Assigning The IP Address The Summit WLAN Adapter Settings menu is displayed (In this screen shown as the SDCCF10G1 menu). 3. Tap on the IP Information tab. Note: Choosing the Renew button forces the 7535 G2 to renew or find a new IP address. This is useful if, for example, you are out of communication range for a longer period of time and your 7535 G2 is dropped from the network. 4. To define a static IP address, tap on the Configure button.
PAGE 60
Chapter 2: Basic Checkout Name Servers Tab 2.8.2 Name Servers Tab Note: If DHCP is enabled, name server addresses are assigned automatically. • In the SDCCF10G1 window, display the IP Information tab. • In the Summit WLAN Adapter Settings>IP Information tab, tap on the Configure button. • Display the Name Servers tab.
PAGE 61
Chapter 2: Basic Checkout Using The SCU To Connect To The WLAN The DNS and WINS fields in the Name Servers tab allow you to specify additional WINS and DNS resolvers. The format for these fields is ###.###.###.###. 2.8.3 Using The SCU To Connect To The WLAN This section provides a quick set of steps to create a profile. Detailed information about each of the SCU tabs—Main, Profile, Status, Diags and Global—is provided in Appendix B: “SCU For RA2041 802.11b/g Radio”.
PAGE 62
Chapter 2: Basic Checkout Using The SCU To Connect To The WLAN • Type a name using any alpha-numeric combination to uniquely identify this profile. • Tap on OK to return to the Profile tab. • Tap on Commit to save the profile name. • When a pop-up message indicates that your configuration will be saved, tap on OK. 2.8.3.1 SSID To configure the SSID for the network to which you want to associate: • Type an SSID in the text box to the right of SSID. This field is limited to 32 characters.
PAGE 63
Chapter 2: Basic Checkout Checking The Scanner Once you’ve completed the configuration: • Tap the Main tab. Tap on the Active Profile button – your new profile will be listed in the drop-down menu. When you tap on the profile you created, the 802.11a/b/g radio module attempts to connect to the network using the following steps: - Associate to the SSID. - Authenticate to the network. - If EAP authentication is being used, derive dynamic encryption keys.
PAGE 64
Chapter 2: Basic Checkout Data Transfer Between The 7535 G2 And A PC 2.10 Data Transfer Between The 7535 G2 And A PC Data transfer options vary slightly depending on the type of operating system installed in your PC. For Windows XP SP2 operating systems or earlier, Microsoft® ActiveSync® is PC connectivity software that can be used to connect your 7535 G2 to PCs running this software.
PAGE 65
Chapter 2: Basic Checkout Resetting The 7535 G2 2.11 Resetting The 7535 G2 To perform a Warm or Cold reset, you can access the menu by going to Start>Shutdown. Alternatively you can use the keyboard shortcuts described below. Warm Reset To execute a warm reset: • Press and hold down the [BLUE] key and the [ENTER/ON] key simultaneously for a minimum of six seconds. A warm reset closes open applications; any unsaved data are lost. Installed programs and saved data are preserved.
PAGE 66
PAGE 67
3 GETTING TO KNOW YOUR 7535 G2 3.1 The Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1.1 Battery Safety . . . . . . . . . . . . . . . . . . . . 3.1.2 Removing And Installing The Battery Pack . . . . . 3.1.3 Battery Chargers . . . . . . . . . . . . . . . . . . . 3.1.4 Monitoring The Battery And Maximizing Run Time 3.1.4.1 Storing Batteries. . . . . . . . . . . . . . . 3.2 Switching The Hand-Held On And Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 68
3.6.2 Scan LED Indicators . . . . . . . . . . . . . . . . . . . . . 3.6.3 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . 3.6.4 Operating One Dimensional (1D) Internal Laser Scanners . . 3.6.5 Operating Internal PDF Laser Scanners. . . . . . . . . . . . 3.6.6 Operating Internal Two Dimensional (2D) Imager Scanners . 3.6.7 Operating RFID/Scanner Modules . . . . . . . . . . . . . . 3.7 Connecting And Disconnecting Tethered Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 69
Chapter 3: Getting To Know Your 7535 G2 The Battery 3.1 The Battery The hand-held operates with a lithium-ion battery pack. Preparing the unit for operation requires that a battery pack be charged and installed in the 7535 G2. 3.1.1 Battery Safety Important: Before attempting to install, use or charge the battery pack, it is critical that you review and follow the important safety guidelines in the section entitled “Lithium-ion Battery Safety Precautions” on page xxiv 3.1.
PAGE 70
Chapter 3: Getting To Know Your 7535 G2 Battery Chargers Figure 3.1 Installing The Battery Pack • 3.1.3 If your computer is equipped with a hand strap, insert the hook at the end of the hand strap into the slot at the base of the battery. Battery Chargers Important: FOR DETAILED INFORMATION about chargers and docking stations, refer to Chapter 6: “Peripheral Devices & Accessories”. For battery safety, refer to “Lithium-ion Battery Safety Precautions” on page xxiv.
PAGE 71
Chapter 3: Getting To Know Your 7535 G2 Monitoring The Battery And Maximizing Run Time • Quad Docking Station (Model #HU4004): can charge the battery of up to four handhelds inserted in the docking station while transferring data through an Ethernet connection. • Powered Cradle (Model # HU1010): can charge the hand-held with the battery installed in the hand-held. It can take from 1.5 to 4 hours to charge a battery.
PAGE 72
Chapter 3: Getting To Know Your 7535 G2 Monitoring The Battery And Maximizing Run Time • The hand-held battery is a ‘smart battery’ with built-in intelligence. The taskbar battery icon is a linear gauge used to estimate the remaining run time of the battery. It is important to note that the battery capacity icon displays quarter percentages of nominal capacity (the capacity of a new battery). An aged battery, even when fully charged, shows somewhat less capacity than nominal.
PAGE 73
Chapter 3: Getting To Know Your 7535 G2 Switching The Hand-Held On And Off 3.2 Switching The Hand-Held On And Off Switching On The Unit • • Press and hold down the [ENTER/ON] key for at least one second. When all four LEDs flash yellow, release the [ENTER/ON] button. Note: If the 7535 G2 is in suspend state, pressing [ENTER/ON] key ‘wakes’ the unit from this state. The screen in which you were working before the computer entered suspend state is displayed.
PAGE 74
Chapter 3: Getting To Know Your 7535 G2 Modifier Keys The [BLUE] and [ORANGE] modifier keys provide access to additional keys and system functions. These functions are colour coded in orange and blue print above the keyboard keys. 36-KEY KEYBOARD 3.3.1 58-KEY KEYBOARD Modifier Keys The [SHIFT], [CTRL], [ALT], [BLUE] and [ORANGE] keys are modifier keys. Pressing a modifier key changes the function of the next key pressed.
PAGE 75
Chapter 3: Getting To Know Your 7535 G2 The Keys 3.3.1.2 Locking Modifier Keys When a modifier key is pressed twice, it is ‘locked’ on. A ‘locked’ modifier key is displayed in uppercase letters in the taskbar. For example, pressing the [BLUE] key twice locks it on—it is displayed as BLUE KEY in the taskbar at the bottom of the computer screen. The locked modifier key will remain active until it is pressed a third time to unlock or turn it off.
PAGE 76
Chapter 3: Getting To Know Your 7535 G2 Function Keys, Softkeys And Macro Keys The [ESC] Key Generally, this key is used as a keyboard shortcut to close the current menu, dialog box or activity and return to the previous one. The [SPACE] Key Pressing this key inserts a blank space between characters. In a Windows dialog box, pressing the [SPACE] key enables or disables a checkbox.
PAGE 77
Chapter 3: Getting To Know Your 7535 G2 Function Keys, Softkeys And Macro Keys To access function keys [F11] to [F20]: • Press the [ORANGE] key followed by the appropriate function key. For example: - To access function key [F11], press the [ORANGE] key followed by [F1]. - To access function key [F12], press [ORANGE] followed by [F2], and so on. To access function keys [F21] to [F30], you’ll need to press [SHIFT] [F1] to [F10]: • Press the [SHIFT] key followed by the appropriate function key.
PAGE 78
Chapter 3: Getting To Know Your 7535 G2 Alphanumeric Keyboard: 58-Key • To access [M4], press [ORANGE] [M2]. Macro keys [M5] to [M6] are colour coded in blue print above macro keys [M1] and [M2]. • • 3.3.4 To access [M5], press the [BLUE] key followed by [M1]. To access [M6], press [BLUE] [M2].
PAGE 79
Chapter 3: Getting To Know Your 7535 G2 Numeric Keyboard: 36-Key To choose the letter ‘b’: • Press the [ORANGE] key, and press [2] twice. • Press the [ORANGE] key again to unlock or turn it off. To choose the letter ‘c’: • • Press the [ORANGE] key, and press [2] three times. Press the [ORANGE] key again to unlock or turn it off. Creating Uppercase Letters To display a capital letter: • Press the [ORANGE] key and then the [SHIFT] key before typing the alpha character.
PAGE 80
Chapter 3: Getting To Know Your 7535 G2 The Keypad Backlight Choosing Multiple Characters From A Range Of Keys If you plan on choosing alpha characters from a number of different keys, you are not required to press the Accept [Þ] key after each alpha selection. The [Þ] key is only required when you are choosing more than one alpha character from the same key, e.g. ‘a’, ‘b’ and ‘c’ from the [2] key. Suppose you want to type the letters ‘a’, ‘d’ and ‘g’.
PAGE 81
Chapter 3: Getting To Know Your 7535 G2 Adjusting The Contrast 3.4.2 Adjusting The Contrast Note: In addition to the manual adjustments described in this section, the display contrast can also be adjusted using the Windows CE Control Panel. Refer to “Backlight” on page 99 for details about this dialog box. The display contrast can be adjusted from the unit keyboard using the [BLUE] key and function keys [F1] and [F2]. Pressing [F1] darkens the display, and pressing [F2] lightens the display.
PAGE 82
Chapter 3: Getting To Know Your 7535 G2 7535 G2 Indicators 3.5 • Select the Calibration tab, and then choose the Recalibrate button. • Follow the directions on the calibration screen to calibrate the screen. 7535 G2 Indicators 7535 G2s use LEDs (Light Emitting Diodes), onscreen messages and audio tones as indicators. 3.5.1 LEDs Hand-helds are equipped with four tri-coloured LEDs. This section outlines what these LEDs indicate.
PAGE 83
Chapter 3: Getting To Know Your 7535 G2 LEDs Figure 3.2 Keyboard LEDs User Application LED Radio Traffic LED Charge LED Scanner LED 3.5.1.1 Charge LED The lower-right LED is reserved for internal charger/power status. This indicator is active even when the hand-held is inserted in a docking station (and in suspend mode) so that the charge status of the battery can be detected easily. Table 3.1 Charge LEDs Function Charge LED Behaviour External power not available.
PAGE 84
Chapter 3: Getting To Know Your 7535 G2 Onscreen Indicators Note: Keep in mind that while the standard 802.11g radio supports the transmit/receive LED, not all radios support this function. Table 3.2 Transmit And Receive LEDs Function Radio Transmit Radio Receive Radio Traffic LED Behaviour LED flashes yellow. LED flashes green. 3.5.1.3 Scan LED Successful scans are indicated in two ways: with a scan LED and with an audio tone. Table 3.
PAGE 85
Chapter 3: Getting To Know Your 7535 G2 Onscreen Indicators Figure 3.3 Taskbar The taskbar changes dynamically, and only those icons that are applicable are displayed. For example, if a radio is not installed in your 7535 G2, the radio signal icon is not displayed in the taskbar. Windows® Start Button If you are using the touchscreen, you can either tap the Windows icon at the bottom left of the screen, or press [BLUE] [0] to display the Start Menu, and then tap on the desired application.
PAGE 86
Chapter 3: Getting To Know Your 7535 G2 Onscreen Indicators Battery Gauge The battery shaped icon displayed in the taskbar provides a visual indication of the remaining battery power. The icon acts as a meter that is either full, at three-quarter level, half, quarter level or empty. When the battery level is low—approximately 15 minutes from empty—a warning window pops up. When the battery power is completely depleted, a final warning window indicates that the 7535 G2 will be powered down.
PAGE 87
Chapter 3: Getting To Know Your 7535 G2 Audio Indicators Docking Device When a hand-held is inserted in a docking station, charger or cradle, an associated icon appears in the taskbar. Gang Charger, Combo Charger & Combo Docking Station Quad Docking Station Power Cradle Portable Docking Module (PDM) Bluetooth Radio This icon displayed in the taskbar represents the installed Bluetooth radio. Security Level Security levels can be set to limit user access.
PAGE 88
Chapter 3: Getting To Know Your 7535 G2 Internal Scanners 3.6 Internal Scanners Important: For detailed scanner specifications and decode zone tables, refer to “Internal Scanner Specifications” on page 206. The 7535 G2 supports a wide range of scanner options to address a variety of user application requirements. The scanner installed in your unit can be configured using the Scanner Settings dialog box in the Control Panel (see page 138) and the Manage Triggers application (see page 114).
PAGE 89
Chapter 3: Getting To Know Your 7535 G2 Scanning Techniques in this chapter. “Scanning Techniques” on page 59 outlines the mechanics of a successful scan. In addition, review “Scan LED Indicators” on page 59 to better understand how to interpret whether or not a bar code has been successfully scanned. Finally, “Troubleshooting” on page 60 provides some helpful suggestions should the scan fail. 3.6.1 Scanning Techniques Note: The scanning techniques described here apply to internal and external scanners.
PAGE 90
Chapter 3: Getting To Know Your 7535 G2 Troubleshooting 3.6.3 Troubleshooting If the scanner is not working, investigate the following: • • • • • • • 3.6.4 Is the unit on? Check that the bar code symbology being scanned is enabled for the hand-held you are using. Check any other parameters that affect the scanning procedure or the bar code. Check the bar code to make sure it is not damaged. Try scanning a different bar code to verify that the problem is not with the bar code.
PAGE 91
Chapter 3: Getting To Know Your 7535 G2 Operating Internal Two Dimensional (2D) Imager Scanners 3.6.6 Operating Internal Two Dimensional (2D) Imager Scanners An imager scanner takes a snap shot of a single bar code or multiple bar codes (at one time). It can find a bar code regardless of its orientation—that is, even a bar code printed at a 45 degree angle to the hand-held will be decoded successfully.
PAGE 92
Chapter 3: Getting To Know Your 7535 G2 Operating RFID/Scanner Modules 3.6.7 Operating RFID/Scanner Modules For detailed information on the RD7950 UHF RFID Reader please refer to the RD7950 UHF RFID Reader Quick Reference Guide (P/N 8000056). Important: For successful reads, the distance from the hand-held to the RFID tag varies depending on the type of tag. 3.
PAGE 93
Chapter 3: Getting To Know Your 7535 G2 Monitoring The Network Connection Figure 3.5 Disconnecting The Tether Cable Important: Never attempt to disconnect a peripheral by pulling the connector by the wire. The connector is locked into place and can only be unlocked and removed by pulling back the plug shell. 3.8 Monitoring The Network Connection If your hand-held is equipped with a wireless LAN radio, it will typically associate with the nearest access point.
PAGE 94
Chapter 3: Getting To Know Your 7535 G2 Uploading Data In A Docking Station 3.9 Uploading Data In A Docking Station The Combo Docking and Quad Docking peripherals allow your hand-held to link to an Ethernet network. They are typically used to upload transaction data to a server computer when a radio link is not available. When a 7535 G2 is properly inserted in a docking station, a dock icon is displayed in the taskbar at the bottom of the unit screen.
PAGE 95
Chapter 3: Getting To Know Your 7535 G2 Cleaning The 7535 G2 • • Avoid abrasive cleaners, solvents or strong chemicals for cleaning. The 7535 G2 has a plastic case that is susceptible to harsh chemicals. The plastic is partially soluble in oils, mineral spirits and gasoline. The plastic slowly decomposes in strong alkaline solutions. To clean ink marks from the keypad and touchscreen, use isopropyl alcohol.
PAGE 96
PAGE 97
4 WINDOWS EMBEDDED CE 5.0 4.1 Navigating In Windows CE And Applications. . . . . 4.1.1 Navigating Using A Touchscreen And Stylus 4.1.2 Navigating Using The Keyboard. . . . . . . 4.2 Working With Files, Folders And Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 69 69 71 4.3 The Startup Desktop . . . . . . . . . . . . . 4.3.1 The Desktop Icons . . . . . . . . . 4.3.2 The Taskbar. . . . .
PAGE 98
68 Psion Teklogix 7535 G2 Hand-Held Computer User Manual
PAGE 99
Chapter 4: Windows Embedded CE 5.0 Navigating In Windows CE And Applications 4.1 Navigating In Windows CE And Applications Note: In order to access many of the menus discussed in this chapter, the security level must be set to ‘Supervisor’ (see “Security Settings” on page 76). Graphic user interfaces like Windows CE for portable devices and desktop Windows (2000, XP, etc.) utilize ‘point and click’ navigation. An equivalent keyboard shortcut is also available for every ‘point and click’ action.
PAGE 100
Chapter 4: Windows Embedded CE 5.0 Navigating Using The Keyboard Table 4.
PAGE 101
Chapter 4: Windows Embedded CE 5.0 Working With Files, Folders And Programs 4.2 Working With Files, Folders And Programs Figure 4.1 Working With Windows Icons Folder Program Icon File • Double-tap on the appropriate icon—either a folder icon, a program icon or a file icon—to open or launch your selection. If you’re using the keyboard: • • 4.3 Use the arrow keys to highlight the icon you want to open or launch. Press [ENTER].
PAGE 102
Chapter 4: Windows Embedded CE 5.0 The Desktop Icons Figure 4.2 The 7535 G2 Startup Desktop To access desktop icons: • Double-tap on the icon to open a window or, in the case of an application icon, launch an application. On the keyboard: • Use the arrow keys to highlight the icon, and press [ENTER] to launch the highlighted icon. Note: If the arrow keys do not highlight the desktop icons, the desktop may not be selected. Press [BLUE] 0 (zero) to display the Start Menu, and select Desktop.
PAGE 103
Chapter 4: Windows Embedded CE 5.0 The Taskbar Internet Explorer Choosing this icon launches Internet Explorer—a standard Windows CE version. Keep in mind that your supervisor will need to set up access using the Internet Options and the Network and Dial-up Connections icons in the Control Panel. Remote Desktop Connection This option allows your 7535 G2 to communicate with a remote desktop PC. “Remote Connect” on page 89 provides a website with step-by-step instructions. 4.3.
PAGE 104
Chapter 4: Windows Embedded CE 5.0 The Taskbar 4.3.2.1 Using The Taskbar A tooltip is displayed as each taskbar icon is highlighted. The tooltip provides the status of each icon. If you’re using the touchscreen: • Tap and hold the stylus on an icon to display the icon's tooltip. Double-tap the icon to open the Control Panel dialog box associated with the icon. For example, double-tap the battery icon to display a dialog box listing the current battery capacity information.
PAGE 105
Chapter 4: Windows Embedded CE 5.0 The Start Menu • Tap the stylus on the items you want to activate or deactivate. The check mark indicates active items. If you’re using the keyboard: • 4.4 Highlight the options you want to activate, and press the [SPACE] key to select them. A check mark indicates active items. The Start Menu Note: Some of the Start Menu items may be disabled based on the current 7535 G2 security settings. The Start Menu lists the operations you can access and work with.
PAGE 106
Chapter 4: Windows Embedded CE 5.0 The Desktop If the menu item has an underlined character: • 4.4.1 Type the underlined alpha character. For example, to display the Security dialog box, type the letter ‘s’. The Desktop Choosing the Desktop option from the Start Menu displays the 7535 G2 desktop. 4.4.2 Security Settings Choosing the Security option from the Start Menu displays a dialog box in which you can define the access level for the 7535 G2: Supervisor or User.
PAGE 107
Chapter 4: Windows Embedded CE 5.0 Security Settings To allow access to all the Start Menu and taskbar options: • • • In the Security Level dialog box, select the radio button next to Supervisor. In the Password field, type the Supervisor level password. The default password is 123456. Select OK. You can now access all menu items in the Start Menu along with the icons in the taskbar.
PAGE 108
Chapter 4: Windows Embedded CE 5.0 Programs 4.4.3 Programs • Choose Programs to display a sub-menu of options. Figure 4.3 Program Sub-Menu This sub-menu allows you to choose ActiveSync and Command Prompt, and you can access the Internet Explorer, installed applications (e.g., Microsoft WordPad), Remote Connect or Windows Explorer. ActiveSync® This option allows you to connect to another device using ActiveSync. Demo This folder contains the Demo Imager, Demo Scanner, and Demo Signature applications.
PAGE 109
Chapter 4: Windows Embedded CE 5.0 Shortcuts double-tapping on the desktop icon My Device and then, double-tapping on the Control Panel icon. Remote Connect Remote Connect is a 7535 G2 application used to connect to a Windows Terminal Server so that you can run a “session” on the Server machine using the 7535 G2 (Windows CE device). “Remote Connect” on page 89 provides a website with details about this option.
PAGE 110
Chapter 4: Windows Embedded CE 5.0 Shortcuts Cycle Tasks When Cycle Tasks is selected (and the Task Manager is not open), you can cycle through active applications. To cycle through your active applications: • • Choose Shortcuts, Cycle Tasks, or Press [ALT] [TAB]. Task Manager The Task Manager allows you to switch to another task or to end an active task. To display the task manager window: • • 80 Tap on Shortcuts, Task Manager, or Press [ALT] [ESC].
PAGE 111
Chapter 4: Windows Embedded CE 5.0 Settings 4.4.5 Settings The Settings sub-menu includes the following settings: Control Panel, Network and Dialup Connections and Taskbar and Start Menu. Figure 4.5 Settings Sub-Menu Control Panel The Control Panel contains applets used to configure hardware, the operating system and the shell. If your 7535 G2 is running with the Psion Teklogix TekTerm application or another application, additional configuration applets may appear in the Control Panel.
PAGE 112
Chapter 4: Windows Embedded CE 5.0 Run 4.4.6 Run Choosing the Run option from the Start Menu displays a dialog box in which you can enter the name of the program, folder or document you want to open or launch. 4.4.7 Shutdown The Shutdown menu includes these options: Suspend, Warm Reset and Cold Reset. Note: This menu varies slightly depending on the security level chosen. When the 7535 G2 is set to User level, the Shutdown option is replaced by Suspend. A sub-menu is not available.
PAGE 113
Chapter 4: Windows Embedded CE 5.0 Using A Dialog Box Suspend The Suspend option suspends the 7535 G2 immediately. This is equivalent to turning the hand-held off. Warm Reset The Warm Reset option resets the 7535 G2, leaving all saved files and (registry) settings intact. Any unsaved data is lost. Cold Reset The Cold Reset option resets the 7535 G2 (see page 35). Any files not stored in permanent memory are lost; however, the registry settings are saved. 4.
PAGE 114
Chapter 4: Windows Embedded CE 5.0 Using A Dialog Box Dialog boxes contain one or more of the following elements: Tab: A tab separates different elements of a dialog box. Press the [TAB] key until a tab in the dialog box is highlighted. To display adjoining tabs, press the [RIGHT] or [LEFT] arrow key. To display the information in the next tab from anywhere in the window, press [CTRL] [TAB]. Textbox: A textbox requires that you type information.
PAGE 115
5 CONFIGURATION 5.1 Remote Connect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 5.2 The TekTerm Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 5.3 Pocket PC Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 5.4 The Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 5.5 Control Panel Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 5.
PAGE 116
5.6.7.7 Built In Devices . . . . 5.6.8 Stylus Properties. . . . . . . . . 5.6.8.1 Double-Tap . . . . . . . 5.6.8.2 Calibration . . . . . . . 5.6.8.3 Touch . . . . . . . . . . 5.6.9 Volume And Sounds Properties . 5.6.9.1 Volume Adjustments . . 5.6.9.2 Sound Adjustments. . . 5.7 Bluetooth Setup . . . . . . . . . . . . . . 5.7.1 Devices . . . . . . . . . . . . . 5.7.2 Headset . . . . . . . . . . . . . 5.7.3 Servers. . . . . . . . . . . . . . 5.7.4 Outgoing. . . . . . . . . . . . . 5.7.5 Active Conn. . . . . .
PAGE 117
5.11.2.3 Removing An Existing Community . 5.11.3 Trap Destination. . . . . . . . . . . . . . . . 5.11.3.1 Enabling Authentication TRAPS . . 5.11.3.2 Adding A Destination . . . . . . . . 5.11.3.3 Changing A Destination . . . . . . . 5.11.3.4 Removing A Trap Destination . . . . 5.11.4 Permitted Hosts . . . . . . . . . . . . . . . . 5.11.4.1 Adding A Host . . . . . . . . . . . . 5.11.4.2 Changing A Host. . . . . . . . . . . 5.12 The Storage Manager . . . . . . . . . . . . . . . . . . 5.12.
PAGE 118
PAGE 119
Chapter 5: Configuration Remote Connect 5.1 Remote Connect Remote Connect is a 7535 G2 application used to connect to a Windows Terminal Server so that you can run a “session” on the Server machine, using the 7535 G2 (Windows CE device). Refer to the following website for step-by-step information about setting up this connection: http://www.microsoft.com/WindowsXP/pro/using/howto/gomobile/remotedesktop/default.asp, or contact Psion Teklogix support services. 5.
PAGE 120
Chapter 5: Configuration Control Panel Icons To access the Control Panel: • Press [BLUE] [0] to display the Start Menu. • Use the stylus to tap on Settings>Control Panel. If you’re using the keyboard: • • Press [BLUE] [0] to display the Start Menu. Highlight Settings in Start Menu, and press the [RIGHT] arrow key to highlight the Control Panel. • Press the [ENTER] key. The Control Panel folder contains icons used in the setup of your 7535 G2. Figure 5.1 Control Panel Icons 5.
PAGE 121
Chapter 5: Configuration Control Panel Icons gives a brief description of each. Section 5.6: “Control Panel Applications: Basic Setup” describes the basic configuration for these applications. App Launch Keys By mapping keys to applications using this program, you can then launch those applications from a single key-press. Bluetooth Devices Provides options for Bluetooth radio setup.
PAGE 122
Chapter 5: Configuration Control Panel Icons Internet Options Provides options to configure your Internet browser. You can determine items such as the default and search page that the browser applies when connecting to the Internet, the cache size, the Internet connection options, and the security level that is applied when browsing. IPv6 Support Refers to a new Internet Protocol specification (version 6) that has been published to use 128-bit IP addresses (replacing version 4).
PAGE 123
Chapter 5: Configuration Control Panel Icons Power Displays battery pack power status. (Alternately, battery status can be accessed through the taskbar.) Additional tabs allow you to determine suspend states, specify a suspend threshold and, when seated in either the Combo Dock or Quad Dock, determine whether or not a battery that requires it can be recalibrated. This dialog box also allows you to activate card slots. (Refer to “Devices” on page 123 for details.
PAGE 124
Chapter 5: Configuration Control Panel Applications: Basic Setup Teklogix Error Handling Service Is an error diagnostic tool that enables you to log error messages to report to Psion Teklogix. Teklogix Scanners Provides scanner parameters and the bar code symbologies that the 7535 G2 scanner will successfully read. Teklogix Imagers The Teklogix Imagers applet is used to create, modify, delete, and activate imager settings. This icon is only present when the appropriate imager is installed.
PAGE 125
Chapter 5: Configuration App Launch Keys To assign an application key: • Tap the Add button. • Press the key you want to use to launch an application. (If an unsupported key is pressed, a message appears on this screen letting you know.) The cursor moves to the App field and a new screen is displayed where you can choose the application to which you want to assign the application key.
PAGE 126
Chapter 5: Configuration App Launch Keys • Once you’ve selected the file you want to map, tap on OK. The cursor moves to the Data field. You can use this field if you need to define special parameters to your application launch key. If you don’t want to assign any parameters, you can leave the Data field blank. If, for example, you want to assign an application launch key to launch the WordPad application, you can leave this field blank.
PAGE 127
Chapter 5: Configuration Certificates 5.6.2 Certificates A public key is transmitted as part of a certificate. The certificates listed in the Certificates tabs ensure that the submitted public key is, in fact, the public key that belongs to the submitter. The 7535 G2 checks that the certificate has been digitally signed by a certification authority that the 7535 G2 explicitly trusts. This option is used in conjunction with 802.1x authentication to enhance 7535 G2 security.
PAGE 128
Chapter 5: Configuration Display Properties 5.6.3 Display Properties • 5.6.3.1 In the Control Panel, choose the Display icon. Background • In the Display Properties dialog box, open the Background tab. This dialog box allows you to customize your background image.
PAGE 129
Chapter 5: Configuration Display Properties 5.6.3.2 Appearance • In the Display Properties dialog box, open the Appearance tab. This dialog box allows you to customize the display colour scheme. 5.6.3.3 Backlight The backlight is activated for a configurable amount of time if the ambient light is below a specified threshold and if the 7535 G2 is in use (key press, scanner trigger).
PAGE 130
Chapter 5: Configuration Display Properties • In the Display Properties dialog box, open the Backlight tab. Note: Backlight changes take effect immediately. You do not need to reset the unit. To maximize battery run time, keep the display backlight brightness and active durations as low as possible. ON Threshold The 7535 G2 is equipped with an ambient light sensor. This sliding bar allows you to determine how dark the ambient light needs to be before the backlight turns on.
PAGE 131
Chapter 5: Configuration Display Properties External Power Checkbox When you select the checkbox next to When using external power keep the backlight always ON, the backlight remains ON at the configured intensity when the 7535 G2 is operating with external power (not battery power). If the 7535 G2 is drawing power from its battery, this option is ignored and the other parameters defined in Display Properties dialog box take affect. 5.6.3.
PAGE 132
Chapter 5: Configuration Input Panel 5.6.4 Input Panel The 7535 G2 is equipped with at Soft Input Panel (SIP). Soft Keyboard Input Panel Button Icon Tapping on the Input Panel button displays a soft input panel (soft keyboard) that can be customized using the Input Panel dialog box. Important: If the Input Panel button icon is not visible in the taskbar, from the ‘Start’ menu, tap on Settings>Taskbar and Start Menu. Tap the checkbox next to ‘Show Input Panel Button’.
PAGE 133
Chapter 5: Configuration Keyboard Properties Figure 5.2 Input Panel Properties • Tap on the Options button to change the appearance of your soft keyboard. Note: You can also display this dialog box by double-tapping on the Input icon in the farright corner of the taskbar. Figure 5.3 Soft Keyboard Options 5.6.
PAGE 134
Chapter 5: Configuration Keyboard Properties • In the Control Panel, choose the Keyboard icon. 5.6.5.1 Key Repeat Note: These settings apply when a key is held down continuously. • In the Keyboard Properties dialog box, open the Repeat tab. Repeat Delay The value assigned for this parameter determines the delay in milliseconds between repeat characters. Sliding the Repeat Delay bar to the left increases the delay between key repeats, and sliding the bar to the right shortens the repeat delay time.
PAGE 135
Chapter 5: Configuration Keyboard Properties Repeat Rate The value assigned for the Repeat Rate parameter determines how quickly the key you press repeats and is measured in characters per second (cps). Sliding the bar to the left slows the repeat rate, and sliding the bar to the right increases the repeat rate. Note: Use the field at the bottom of this dialog box to test the repeat delay and rate settings you’ve chosen. 5.6.5.
PAGE 136
Chapter 5: Configuration Keyboard Properties Note: Tapping in the checkbox next to ‘When using external power, keep the backlight always ON’ forces the keypad backlight to remain on when the unit is operating with external power. 5.6.5.3 Keyboard One Shot Modes • In the Keyboard Properties dialog box, open the One Shots tab. The options in this tab allow you to determine how modifier keys on your 7535 G2 behave.
PAGE 137
Chapter 5: Configuration Keyboard Properties OneShot If you choose OneShot, the modifier key remains active only until the next key is pressed. OneShot/Lock OneShot/Lock allows you to combine these functions. When you choose this option and you press the modifier key once, it remains active only until the next key is pressed. If you press the modifier key twice, it is locked ‘on’, remaining active until the modifier key is pressed a third time to turn it ‘off’. 5.6.5.
PAGE 138
Chapter 5: Configuration Keyboard Properties A message screen is displayed instructing you to Enter Key Strokes to Record • Type the macro sequence you want to assign to the Macro key. You can type text and numbers, and you can program the function of special keys into a macro. • When you’ve finished recording your macro sequence, press the key sequence: [CTRL] [ALT] [ENTER], or choose the Stop Recording button. A new screen called ‘Verify Macro’ displays the macro sequence you created.
PAGE 139
Chapter 5: Configuration Keyboard Properties 5.6.5.5 Unicode Mapping • In the Keyboard Properties dialog box, open the Unicode Mapping tab. The Unicode Mapping tab is used to map combinations of virtual key values and [CTRL] and [SHIFT] states to Unicode™ values. This tab shows the configured Unicode character along with the Unicode value. For example, the sample screen above shows “a (U+0061)” indicating that the character “a” is represented by the Unicode value “0061”, and so on.
PAGE 140
Chapter 5: Configuration Keyboard Properties • Choose the Add/Change button. • Highlight a value in the Unicode mapping list. In the sample screen above, a value will be assigned to virtual key 0 (VK 0). Position the cursor in the Unicode Mapping field, and type a Unicode value for the highlighted key. • Note: To add a shifted state, [SHIFT] and/or [CTRL], press [TAB] to position the cursor in the checkbox next to ‘SHIFT Pressed’ and/or ‘CTRL Pressed’.
PAGE 141
Chapter 5: Configuration Keyboard Properties key presses that occur when the [BLUE] modifier is on; the Orange table defines key presses that occur when the [ORANGE] modifier is on. The default mappings of these scancodes can be overwritten for each of these three tables using the Scancode Remapping tab accessed from the Keyboard Properties dialog box. The first column in the Scancode Remapping tab displays the scancodes in hexadecimal.
PAGE 142
Chapter 5: Configuration Keyboard Properties The Remap Scancode dialog box is displayed. • Type the scan code in hexadecimal in the field labelled Scancode Note: The Label field displays the default function of the scancode you are remapping. Virtual Key, Function And Macro The radio buttons at the bottom of the dialog box allow you to define to what the scan code will be remapped: Virtual Key, Function or Macro.
PAGE 143
Chapter 5: Configuration Keyboard Properties Removing A Remap To delete a remap: • • In the Scancode Remapping tab, highlight the scancode you want to delete, and tap on the Remove button. Tap on OK. 5.6.5.7 Lock Sequence The Lock Sequence menu allows you to lock the 7535 G2 keyboard to prevent keys from being pressed accidentally when, for example, the unit is inserted in a holster. • • • To lock the keyboard, tap in the checkbox next to Enable key lock sequence.
PAGE 144
Chapter 5: Configuration Manage Triggers A locked keyboard icon is displayed in the softkey bar when the keyboard is locked. Locked Keyboard Icon • 5.6.6 Type the key sequence to unlock the keyboard. Manage Triggers Allows users to configure how bar code scanners and other devices such as RFID readers are triggered. You can configure the trigger ID for each trigger button for both single- and double-click, and the double-click time. • 114 In the Control Panel, choose the Manage Triggers icon.
PAGE 145
Chapter 5: Configuration Manage Triggers • In the Manage Triggers screen you’ll see a list of trigger mappings. 5.6.6.1 Trigger Mappings A trigger mapping is an association between a particular key on the keyboard and a driver or application, the module(s)—sometimes referred to as “trigger consumer(s)”—of the trigger source. Along with keyboard keys, the external trigger (scan button) is software-based. When the specified key is pressed, the owner (for example, a decoded scanner) is sent a message.
PAGE 146
Chapter 5: Configuration Manage Triggers Show All Modules By default, the trigger mapping list only shows active mappings. Mappings for drivers or applications that are not currently active are not normally displayed. By checking this checkbox, all mappings, both active and inactive, are displayed. Add Tapping this button brings up the Add Mapping dialog (see page 116), so that you can add new trigger mappings.
PAGE 147
Chapter 5: Configuration Manage Triggers Trigger Key This drop-down list allows you to specify the source of the trigger events, such as the Soft Scan, Left Scan, etc., for the trigger module selected. Note: It is possible to map the same source to different modules (trigger consumers)—for example, to both the Imager and Non-Decoded Scanner. If so, both devices/operations will occur simultaneously. This is not recommended in most cases, especially with devices such as Imagers or RFID Readers.
PAGE 148
Chapter 5: Configuration Power Management Properties Module Trigger This identifies the driver or application receiving the trigger presses. Show All Modules By default, inactive owners are not shown. By checking this checkbox, all owners, both active and inactive, are displayed. 5.6.7 Power Management Properties This icon displays a Power Properties dialog box that indicates the unit’s battery capacity and allows you to manage battery use. • 118 In the Control Panel, choose the Power icon.
PAGE 149
Chapter 5: Configuration Power Management Properties 5.6.7.1 Battery Capacity • In the Power Properties dialog box, open the Battery tab to view battery details. 5.6.7.2 Power Saving Suspend • In the Power Properties dialog box, open the Suspend tab. Power Source This drop-down menu allows you to specify whether the unit is using AC Power or Battery Power.
PAGE 150
Chapter 5: Configuration Power Management Properties Suspend Timeout Important: Psion Teklogix recommends setting the Suspend value to 10 minutes. To further reduce power consumption, carefully consider the duration of time that the display backlight is ‘on’ (see “Backlight” on page 99).
PAGE 151
Chapter 5: Configuration Power Management Properties Important: Selecting Maximum backup time will reserve approximately 20% of the battery capacity for memory backup. Once the battery is drained, the system RAM memory is lost and the unit must cold boot. In most real-time transaction environments this is not a problem (it only takes a few seconds to cold boot).
PAGE 152
Chapter 5: Configuration Power Management Properties 5.6.7.4 Calibrate Tapping in the checkbox next to Allow Battery Calibration allows the battery to be recalibrated only when necessary if the unit is inserted in a Combo Docking station. 5.6.7.5 Advanced Allow Suspend With: This tab allows you to specify whether or not your unit will enter Suspend state while it is operating with an active PPP connection, network interface, or active TCP/IP connection.
PAGE 153
Chapter 5: Configuration Power Management Properties Low Power Warnings The sliding scale at the bottom of this tab allows you to specify the remaining battery capacity at which a warning message is displayed on the 7535 G2 screen, from 0% to 20%. 5.6.7.6 Devices This tab controls power to individual CF and SDIO slots. Enable or disable the checkboxes as needed, then tap on OK to save your changes. 5.6.7.7 Built In Devices This tab controls power to built-in devices such as Bluetooth.
PAGE 154
Chapter 5: Configuration Stylus Properties 5.6.8 Stylus Properties Note: Touchscreen calibration may not be enabled on your unit. If your screen appears to require recalibration, contact your supervisor. • In the Control Panel, choose the Stylus icon. 5.6.8.1 Double-Tap • In the Double-Tap menu, follow the directions to tailor the sensitivity of the stylus when you tap on the touchscreen. 5.6.8.2 Calibration Touchscreens rarely require recalibration.
PAGE 155
Chapter 5: Configuration Volume And Sounds Properties • Choose the Calibration tab, and then tap on the Recalibrate button. • Follow the directions in the Calibration tab to recalibrate the screen. 5.6.8.3 Touch This tab allows you to disable the touchscreen. • 5.6.9 Choose the Touch tab. Select the checkbox next to Disable the touch panel. Volume And Sounds Properties • In the Control Panel, choose the Volume & Sounds icon.
PAGE 156
Chapter 5: Configuration Bluetooth Setup 5.6.9.1 Volume Adjustments • • Slide the volume button to the left to lower the beeper volume or to the right to increase the beeper volume. Under the heading Enable sounds for, enable the conditions under which you want the 7535 G2 to emit a beep. 5.6.9.2 Sound Adjustments The 7535 G2 computer is equipped with a beeper rather than a sound port. The options under this tab are not available for this hand-held. 5.
PAGE 157
Chapter 5: Configuration Devices • In the Control Panel, choose the Bluetooth Devices icon to display the Bluetooth Manager screen. The Bluetooth Manager dialog box displays the other Bluetooth devices with which you can communicate. 5.7.1 Devices If you intend to pair devices (a scanner or printer for example), power on and bring the devices within 5 m (16.4 ft.) of the 7535 G2 before proceeding with the discovery process described below.
PAGE 158
Chapter 5: Configuration Devices Pairing A Device To pair devices: • Follow the manufacturer’s instructions to place the device you want to pair in pairing mode • Choose the Devices tab and Scan for devices in your area. • When the scan is complete, highlight the device you want to pair with and either doubleclick or press the Services button. • If a PIN dialog box appears, type your PIN and tap on OK.
PAGE 159
Chapter 5: Configuration Devices Note: During the scanning process, addresses are located first, followed by names. Only the names of devices that are within the Bluetooth radio coverage range will be retrieved. The Active column indicates whether any service is activated for that device. When a service is activated, the device is displayed in the list even when it is not detected during the scan. The PIN column indicates whether you have a PIN (password) set for the device.
PAGE 160
Chapter 5: Configuration Devices To add a service to the Outgoing port, an active service must first be deactivated. Then you can choose the Outgoing option from the Activation menu (highlight a service, right-click or press the [SPACE] bar to display the Activation menu). The Authentication and Encryption options can be changed only before activation. To change these after activation, deactivate the service first, then change the options.
PAGE 161
Chapter 5: Configuration Headset 5.7.2 Headset To pair a headset with your 7535 G2: • Place your headset in Discoverable mode. You can do this by following the manufacturer’s instructions in your headset’s user guide. • Search and discover your headset. Choose the Devices tab in Bluetooth Manager and scan for devices in your area. (Note that if this is your first time pairing, the device scan occurs automatically—you do not need to tap on the Scan button to perform a scan.
PAGE 162
Chapter 5: Configuration Servers 5.7.3 Servers When the Bluetooth connection is initiated from your 7535 G2 to the remote device, the 7535 G2 is called the ‘client’ and the remote is called the ‘server’. The Servers menu displays the server profiles that can be activated in your 7535 G2. There are currently two server profiles available: Serial and Scanner. • Tap on the checkbox to activate the server, and it will display the associated port name beside the server name.
PAGE 163
Chapter 5: Configuration Outgoing 5.7.4 Outgoing Outgoing Port acts as a serial port that can be used to connect to a list of Bluetooth devices (one at a time), but you have the freedom to switch on-the-fly. The Outgoing Port checkbox allows you to create the Outgoing port. When the port is created, the Outgoing tab lists the port name. The Outgoing list dialog box displays a list of services marked as ‘Outgoing’. The * column indicates the currently selected service.
PAGE 164
Chapter 5: Configuration Active Conn. 5.7.5 Active Conn. The Active Conn. menu lists the Name, Address, and Type of the currently active connections. The table is periodically updated, but it can take a few seconds before it reflects the actual list of connections. The Type column of the table shows ‘ACL’ or ‘SCO’. The Connection list table shows the connections for scanning as well as the service connections.
PAGE 165
Chapter 5: Configuration Properties 5.7.6 Properties The Properties menu displays information about your 7535 G2, and provides some port options. The Device Name field shows the device name of your 7535 G2. This name can be changed (see the Note on the previous page for details). Device Class shows the Class of Device (e.g. desktop, hand-held), which is always set to Handheld. Local Bluetooth Address shows the address of your 7535 G2 radio. Port Prefix is used to set the port name to either BSP or COM.
PAGE 166
Chapter 5: Configuration Search For 5.7.7 Search For The Search For menu allows you to specify the services for which the Bluetooth radio will scan. 5.8 Error Reporting Error Reporting allows you to enable or disable Microsoft error reporting prompts. • 136 Tap on Start>Settings>Control Panel>Error Reporting icon to access your options.
PAGE 167
Chapter 5: Configuration IPv6 Support 5.9 IPv6 Support The IPv6 Support icon in the Control Panel allows you to activate IPv6 network support on your unit if your network setup requires this. This internet protocol specification (version 6) supports 128-bit IP addresses, replacing version 4. • Choose the IPv6 Support icon to display the associated dialog box. • Choose the checkbox next to Enable IPv6 Network Support to enable this internet protocol.
PAGE 168
Chapter 5: Configuration Scanner Settings 5.10 Scanner Settings The Teklogix Scanners icon in the Control Panel provides dialog boxes in which you can tailor bar code options and choose the bar codes your scanner will recognize. The parameters are preset with the default settings of the decoded scanner installed in the unit. For a listing of available scanners and their specifications, please refer to Chapter 7: “Specifications”.
PAGE 169
Chapter 5: Configuration Bar Codes 5.10.1 Bar Codes 5.10.1.1 Scanner The drop-down menu to the right of the Scanner option allows you to choose configurations for one of the following scanner types, depending on what is installed in/on your hand-held: Decoded (internal), Decoded (Intermec ISCP), Imager and Non-decoded. The symbologies listed in the Barcodes tab change to reflect the scanner you choose and the bar codes it supports.
PAGE 170
Chapter 5: Configuration Bar Codes Restoring Default Settings • • For the Symbol LS3408 decoded scanner, refer to the programming guide supplied with your scanner. For PowerScan® (PSC) decoded scanners, refer to the PowerScan Programming Guide. 5.10.1.2 Restoring Default Settings If you want to restore the factory defaults after making changes, the defaults can be applied to a selected parameter, sub-tree of parameters or all scanner parameters. • Press and hold the stylus on a symbology (e.g.
PAGE 171
Chapter 5: Configuration Options • Press and hold the stylus on the parameter you want to reset. • Choose Default parameter to reset the parameter to the default setting. 5.10.2 Options This tab allows you to tailor the double-click parameters and the display options associated with your scanner. 5.10.2.1 Double Click Parameters Click Time (msec) This parameter controls the maximum gap time (in milliseconds) for a double-click.
PAGE 172
Chapter 5: Configuration Options sidered a double-click. The allowable range is 0 to 1000. A value of zero disables this feature. A double-click produces different results depending on whether or not a value is assigned in the “Click Data” parameter. When a value is not assigned for the “Click Data”, double-clicking the scanner trigger overrides the target dot delay set in the “Dot Time” parameter and initiates a normal scan sweep.
PAGE 173
Chapter 5: Configuration Translations Good Scan Beep And Bad Scan Beep These parameters determine whether or not the 7535 G2 emits an audible scanner ‘beep’ when a good (successful) scan or a bad (unsuccessful) scan is performed. Set these parameters to either on to enable the beeper or off to disable it. Soft Scan Timeout This parameter is used by the SDK “Scan” function (soft-scan: starting a scan session via the SDK function, instead of a physical user trigger press).
PAGE 174
Chapter 5: Configuration Translations 144 • In the Translation menu, tap on the Case # to create rules. • Tap on the No rule drop-down menu to display the rules.
PAGE 175
Chapter 5: Configuration Translations When you choose a rule, an associated screen is displayed in which you can define the rule. 5.10.3.1 Case Rules The case rules are defined as follows: • • • • • • • No rule—ignored. Search and replace—replaces all instances of the match string. (Note that this rule cannot fail.) Match at index—matches the match string at a specified index. Match and replace at index—matches the match string at a specified index and replaces/changes it.
PAGE 176
Chapter 5: Configuration Ports 5.10.4 Ports Figure 5.4 Tether, Console, and Port Replicator Port Settings While you cannot configure the scanner, you can configure communications with a serial decoded scanner using the options in this tab. Use these settings to ensure that the communication ports on the 7535 G2 match the settings of the serial devices to which they are connected. If the settings do not match exactly, the devices may not function.
PAGE 177
Chapter 5: Configuration Ports 5.10.4.1 Tether Port (COM1) Note: RS-232 serial communication is one of the modes available on the tether port, located on the side of the 7535 G2. These parameters refer only to external decoded scanner communications. They have no effect if the generic serial device tether cable is plugged in. Baud Double-tapping on this parameter displays a pop-up window in which you can choose an appropriate rate of data transfer. Figure 5.
PAGE 178
Chapter 5: Configuration Ports Parity This parameter determines the type of parity checking used on the data going through the tether port. Double-tapping on this option displays a pop-up window in which you can choose the appropriate Parity. Stop Bits This parameter specifies the number of stop bits—1, 1.5 or 2—used for asynchronous communication. 5.10.4.2 Console Port (COM3) The console port is accessed via the docking connector on the bottom of the 7535 G2.
PAGE 179
Chapter 5: Configuration Ports Data Bits Refer to page 147 for details about this parameter. Parity For details, refer to page 148. Stop Bits Refer to page 148 for details about Stop Bits. 5.10.4.3 Port Replicator Tether (COM6) The port replicator tether is a duplicate tether port located on the port replicator module of the 7535 G2 cradles. Figure 5.7 Port Replicator Tether Settings Baud Refer to page 147 for details. Data Bits Refer to page 147 for details about this parameter.
PAGE 180
Chapter 5: Configuration Ports 5.10.4.4 Port Replicator Port A (COM5) Port Replicator Port A(COM5) is the standard RS-232 DE-9 DTE port on the 7535 G2 port replicator module, available on certain cradle types. Enabled This parameter must be set to ON in order for the 7535 G2 to recognize the device connected to the Port Replicator 9-pin (COM5). Baud Refer to page 147 for details. Data Bits Refer to page 147 for details about this parameter. Parity For details, refer to page 148.
PAGE 181
Chapter 5: Configuration SNMP (Simple Network Management Protocol) Setup 5.11 SNMP (Simple Network Management Protocol) Setup Simple Network Management Protocol (SNMP) is the protocol used to monitor and manage devices attached to a TCP/IP network (providing they support SNMP). SNMP uses Management Information Bases (MIBs) that define the variables an SNMP Network Management Station can access. Each product has a defined set of MIBs that determine how SNMP operates, the type of access allowed and so on.
PAGE 182
Chapter 5: Configuration Contact 5.11.1 Contact The SNMP dialog box is displayed. Contact This field identifies the contact person for this managed node along with information about how to get in touch with this person. The content of this parameter is accessible through MIB-II’s sysContact object. Location This parameter is used to identify the physical location of this node (e.g., Warehouse A: Pillar 32B). The content of this parameter is accessible through MIB-II’s sysLocation object.
PAGE 183
Chapter 5: Configuration Communities 5.11.2 Communities The Communities tab allows you to limit access to SNMP-managed devices to those SNMP Managers with matching “community names”, as specified by RFC 1157. Enable SNMP Tapping the checkbox Enable SNMP allows the device to respond to SNMP queries and to send Traps. After enabling this option and rebooting the device, the SNMP Agent will automatically start up. To disable this feature, remove the checkmark from the checkbox. 5.11.2.
PAGE 184
Chapter 5: Configuration Communities Rights This menu allows you to specify access, that is, ‘Read-Only’ or Read-Write’ 5.11.2.2 Modifying A Community Setting To modify an existing community: • • Highlight the community you want to alter. Choose the Change button. A Modify Community dialog box is displayed, listing the community you highlighted. • Edit the Name and/or Rights, and press [ENTER] to save your changes. 5.11.2.
PAGE 185
Chapter 5: Configuration Trap Destination 5.11.3 Trap Destination A trap is an unsolicited report sent to SNMP Managers by the SNMP Agent running on the managed node. This option allows you to define where the report will be sent. 5.11.3.1 Enabling Authentication TRAPS Enabling Enable Authentication TRAPS allows authorization traps to be sent when a failure is detected (e.g., an SNMP message received with a bad community name). 5.11.3.
PAGE 186
Chapter 5: Configuration Permitted Hosts A dialog box like the one displayed when you add a destination is displayed. • Make the changes to the destination, and press [ENTER] to save the changes. 5.11.3.4 Removing A Trap Destination To remove a trap destination: • In the Trap Destination tab, highlight the destination you want to delete. • Choose the Remove button. A Delete Confirmation screen is displayed.
PAGE 187
Chapter 5: Configuration Permitted Hosts 5.11.4.1 Adding A Host To add a new host: • Highlight the Add button, and press [ENTER]. • Type a new host IP address in the text box provided, and press [ENTER]. 5.11.4.2 Changing A Host To change an existing host IP address: • Highlight the IP address you want to alter in the Permitted Hosts tab, and then choose the Change button. A dialog box like the one displayed when you add a host is displayed. • Make the necessary changes, and press [ENTER].
PAGE 188
Chapter 5: Configuration The Storage Manager 5.12 The Storage Manager The Storage Manager allows you to view information about the storage devices that are present in the 7535 G2, such as SD-MMC flash cards and Compact Flash cards. 5.12.1 Formatting A Memory Card Formatting a memory card bulk-erases it. Once a card is erased, partitions may be created in it, similarly to those on a hard drive. Memory-card devices are normally ‘mounted’ (made available to the system) automatically when they are inserted.
PAGE 189
Chapter 5: Configuration Creating Partitions 3. Select the memory card from the drop-down list. 4. Press the Dismount button to dismount the memory card. All partitions on the card will be dismounted. 5. Press the Format button to format the memory card. All partitions and information on the card will be erased during the formatting process. 5.12.2 Creating Partitions Once the card is formatted, new partitions can be created in it.
PAGE 190
Chapter 5: Configuration Partition Management 3. If more than one partition is desired, uncheck the Use All Available Diskspace checkbox, then specify the desired number of sectors to be used by the partition. 4. Press OK. The new partition appears in the Partitions list: The new partition is automatically mounted. This is indicated by an asterisk (*) next to its name in the partition list. Any unallocated space on the card is indicated at the left, and additional partitions can be created in it. 5.12.
PAGE 191
Chapter 5: Configuration Partition Management To dismount a partition: 1. Choose the desired partition. 2. Tap the Properties button. The Partition Properties dialog appears. 3. Tap the Dismount button. The partition is dismounted. The asterisk disappears next to its name in the partitions list. To delete a partition: 1. Select the desired partition. 2. Tap the Delete button. A warning dialog appears. 3. Tap the OK button. The partition is deleted. To format a partition: 1. Choose the desired partition. 2.
PAGE 192
Chapter 5: Configuration Teklogix Error Handling Service • Cluster size (.5 KB to 64 KB). There are also two checkboxes, which govern: • Whether to use the transaction-safe FAT file system (TFAT). This file system keeps multiple copies of the file-allocation table, changing one while maintaining another as a backup. • Whether to perform a quick format. Quick formatting removes all reference to data in the partition without erasing the actual partition.
PAGE 193
Chapter 5: Configuration ErrorLogInfo 5.13.1 ErrorLogInfo • To log an error, tap on the ErrorLogInfo tab. • Choose an Error Level, and tap on FlushToFile to log the information file. 5.13.2 NetLog The NetLog option is used to log network traffic. When you tap in the checkbox to the left of Enable NetLog Debug Capturing, debug data is collected so that, if necessary, it can be forwarded to a Psion Teklogix technician for evaluation.
PAGE 194
Chapter 5: Configuration Teklogix Imagers 5.14 Teklogix Imagers The Teklogix Imagers applet is used to create, modify, delete, and activate imager settings. The principle uses of the applet are to decode bar codes and to capture images. A PTSI Imager demo applet is also provided to illustrate how the imager works. Refer to Appendix D: “Teklogix Imagers Applet” for configuration details. To launch this applet: • In the Control Panel, choose the Teklogix Imagers icon.
PAGE 195
Chapter 5: Configuration Total Recall 5.15 Total Recall Total Recall is a Psion Teklogix utility developed to maintain applications and settings during a cold boot. This utility is based on a backup and restore concept. This utility is based on a backup and restore concept • In the Control Panel, choose the Total Recall icon. 5.15.
PAGE 196
Chapter 5: Configuration Creating A Backup Profile Profile Information This dialog box lists the possible storage destinations for the profile file. 1. To begin, type a name for the profile in the field labelled Profile Name. 2. Choose the Profile Type you want to create: For this device only—creates a backup that is manually restored by the operator. AutoRestore for this device only—creates a profile that automatically restores itself following a restart.
PAGE 197
Chapter 5: Configuration Creating A Backup Profile Add Files By default, All Files is selected so that all installed or copied files, database entries, and the Registry will be saved. You can, however, limit the backup to databases, and/or the registry only. By tapping the checkbox next to these items, you can add or remove a check mark to enable or disable the option. The Select Files option allows you to select predefined file types. • • Remove the check mark next to All Files.
PAGE 198
Chapter 5: Configuration Creating A Backup Profile To add a file to your backup list: • Choose Add Files. Browse to and choose the files you want to add to your list. To remove a file from your backup list: • Choose Remove Files—a dialog box is displayed listing the files that will be backed up. • Highlight the item you want to remove from the list, and tap on the Remove button. Choosing By File Type allows you to select the file types that you want backed up.
PAGE 199
Chapter 5: Configuration Restoring A Profile View Selections Depending on what you have selected for inclusion in your profile, you can view a list of the selected files, databases and/or registry. • Choose the Next button to perform the operation. Perform The Operation • Choose the Backup button to start the process, and create a profile. 5.15.
PAGE 200
Chapter 5: Configuration TweakIT Settings 5.16 TweakIT Settings This utility allows you to ‘tweak’ or adjust Advanced system settings (interface, network, servers, driver, and radio), User settings (Internet Explorer settings, font size, and docking port message), and provides a Registry Editor. 5.16.1 Advanced 5.16.1.
PAGE 201
Chapter 5: Configuration Advanced Modem Logging When this option is enabled, the 7535 G2 logs AT commands (e.g., dial-out information, password string, etc.) that the administrator can monitor for debugging purposes. Modem commands are stored in: \MdmLog.txt. 5.16.1.2 Advanced Services Settings FTP Server This option is enabled by default to allow file transfers.
PAGE 202
Chapter 5: Configuration Advanced 5.16.1.3 Advanced Intermediate Driver Intermediate Driver Support The 7535 G2 employs a custom intermediate driver that is used to indicate radio transmission and reception on its LEDs. As well, the intermediate driver is employed to support the Psion Teklogix 802.IQ v1 protocol. This TweakIt option is included to allow the driver to be disabled in cases where it interferes with third party drivers or security supplicants.
PAGE 203
Chapter 5: Configuration Advanced 5.16.1.4 Radio Features AP Density This option allows you to determine the signal strength at which the 7535 G2 radio will begin searching for a new Access Point (AP): High, Medium or Low. If, for example, this option is set to High, the radio will begin searching for a new Access Point while still at a fairly strong signal strength.
PAGE 204
Chapter 5: Configuration User 5.16.2 User 5.16.2.1 Internet Explorer Settings This option allows you to customize how your Internet Explorer is displayed and how the tabbing functions. 5.16.2.
PAGE 205
Chapter 5: Configuration User User Font Size This option allows you to adjust the size of the font used the 7535 G2 display: Large, Normal or Small. 5.16.2.3 User System Settings Docking Port Message Checking this box blocks the message that normally pops up on the display when the 7535 G2 is docked.
PAGE 206
Chapter 5: Configuration Registry Editor 5.16.3 Registry Editor This option is reserved for senior administrators who have a strong understanding of registry keys and values. Careless registry editing can cause irreversible damage to the 7535 G2.
PAGE 207
6 PERIPHERAL DEVICES & ACCESSORIES 6.1 External Bar Code Readers. . . . . . . . . . . . . . . . . . . . . . 6.1.1 PowerScan® Standard, LR and XLR Bar Code Scanners . 6.1.2 Entering Data With The Bar Code Reader . . . . . . . . . 6.2 RD7950 Integrated UHF RFID Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .179 .179 .179 .179 6.3 Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180 6.4 Battery Charging .
PAGE 208
6.8 Quad Dock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.8.1 Installation. . . . . . . . . . . . . . . . . . . . . . . . 6.8.2 Indicators And Controls . . . . . . . . . . . . . . . . . 6.8.3 Using The Quad Dock. . . . . . . . . . . . . . . . . . 6.8.4 Network Access . . . . . . . . . . . . . . . . . . . . . 6.8.4.1 Network Addressing . . . . . . . . . . . . . . 6.8.5 Battery Charging . . . . . . . . . . . . . . . . . . . . 6.8.6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . 6.8.
PAGE 209
Chapter 6: Peripheral Devices & Accessories External Bar Code Readers 6.1 External Bar Code Readers 6.1.1 PowerScan® Standard, LR and XLR Bar Code Scanners Note: Refer to “PowerScan Standard Range Scanner Specifications” on page 219 and “PowerScan® LR and XLR Industrial Scanner Specifications” on page 216 for detailed specifications. The 7535 G2 supports Psion Teklogix’ PowerScan® industrial bar code scanner with standard, long range and extra long range options.
PAGE 210
Chapter 6: Peripheral Devices & Accessories Batteries 6.3 Batteries Note: Battery specifications are detailed beginning on page 221. 7535 G2s operate with lithium-ion batteries—a high capacity 1900 mAh battery pack. For detailed safety instructions, please see “Lithium-ion Battery Safety Precautions” on page xxiv. For details on battery charging and installation, see “Powering Up The 7535 G2” on page 14. For battery calibration and power settings, see “Power Management Properties” on page 118. 6.
PAGE 211
Chapter 6: Peripheral Devices & Accessories Gang Charger A feature is built into the HU3006 gang charger and the HU3002/HU4002 Combo Charger/Dock which detects a battery that requires calibration and will fully discharge it and charge it—but only if the remaining capacity is less than 30% of a full charge. On the HU3006, only one of the six slots can perform a calibration cycle at any one time. This calibration cycle extends the overall charge time by up to 4 hours.
PAGE 212
Chapter 6: Peripheral Devices & Accessories Operator Controls • Install the IEC power cord and apply power. A green indicator in the lower-right indicates power is present. All charge indicators flash momentarily at powerup to indicate that the charger is ready for operation. If you choose to wall mount the charger, follow the instructions packaged with the mounting bracket kit. Be sure to locate the charger in an area where there is no risk of injury to persons walking in the vicinity. 6.5.
PAGE 213
Chapter 6: Peripheral Devices & Accessories Charging Batteries 6.5.4 Charging Batteries • Install the battery with the battery contacts facing the charger. Slide the battery between the guide rails until it lightly latches in place. The LED directly below the slot in which a battery is inserted lights up immediately. A solid yellow LED indicates that the battery is being charged.
PAGE 214
Chapter 6: Peripheral Devices & Accessories Combo Charger 6.5.5.3 Indicator Flashing Red If the indicator flashes red: • Remove all batteries and disconnect the mains power cable. • Wait at least 20 seconds, and then plug the cable in again. If any of the charge slot LEDs continue to flash red, the charger is defective and requires service. If all indicators are flashing red, there is a power supply problem and the charger requires service. 6.5.5.
PAGE 215
Chapter 6: Peripheral Devices & Accessories Operator Controls • Visually inspect the charger for possible damage. • Install the IEC power cord and apply power. A green LED in the lower-right corner of the front panel lights to indicate that power is present. The charge LED flashes momentarily at powerup. The charger is now ready for operation. 6.6.2 Operator Controls The combo charger has no operator controls or power switch. 6.6.
PAGE 216
Chapter 6: Peripheral Devices & Accessories Charge Indicators 6.6.5 Charge Indicators The spare battery charge slot has an associated tri-colour LED indicator on the lower-right area of the front panel. The charge indicators are the same as those for the Gang Charger. For a description of the charger indicators, please refer to Table 6.1 on page 182. The combo charger supplies DC power to enable the 7535 G2 internal fast charger. Charge status is displayed on the 7535 G2 charge LED (the lower-right LED).
PAGE 217
Chapter 6: Peripheral Devices & Accessories Network Access The battery charge LED (lower-right LED) on the 7535 G2 lights up to show it has external power and may start charging the battery. Interaction with the 7535 G2 while in the combo dock is a function of the user application software used to communicate with the host network. 6.7.3 Network Access The combo dock includes a dedicated USB to Ethernet converter. This USB converter appears as a USB slave to the 7535 G2 USB host controller.
PAGE 218
Chapter 6: Peripheral Devices & Accessories Indicators And Controls • Visually inspect the unit for any damage. • Install the IEC power cord and apply power. A green indicator in the lower-right corner of the front panel lights up to indicate that power is present. • Attach a CAT5 RJ45 network patch cable (supplied) between your network and the RJ45 jack on the rear of the dock. A green LED is illuminated next to the RJ45 connector when a valid network link is established.
PAGE 219
Chapter 6: Peripheral Devices & Accessories Battery Charging 6.8.4.1 Network Addressing Although the USB converters have fixed Ethernet MAC addresses, there is generally no correlation between these addresses and a specific 7535 G2 hand-held. The host application uses standard TCP/IP protocol to name, locate and communicate with a specific 7535 G2 on the network.
PAGE 220
Chapter 6: Peripheral Devices & Accessories Portable Docking Module (PDM) 6.9 Portable Docking Module (PDM) Warning: The mains power cord for the AC/DC adaptor shall comply with national safety regulations of the country where the equipment is to be sold. The Portable Docking Module (PDM) clips onto the base of the 7535 G2 and is most often used to charge the 7535 G2 battery when a desktop charger is not convenient.
PAGE 221
Chapter 6: Peripheral Devices & Accessories Portable Docking Module (PDM) Figure 6.1 Attaching The PDM To The Base Of The 7535 G2 Align the guide pins on the PDM with the slots on the base of the 7535 G2, and gently snap the PDM onto the hand-held. Guide Pins Figure 6.
PAGE 222
Chapter 6: Peripheral Devices & Accessories Bluetooth Peripherals The interfaces available on the PDM are as follows: • • • AC/DC adaptor jack (15VDC @ 2.5A). Type A USB host port (for connection to USB devices such as a mouse, keyboard, printer, etc.). Type B USB device port (for connection to a USB host such as a PC).
PAGE 223
Chapter 6: Peripheral Devices & Accessories The 7535 G2 Picker Cradle Keep in mind that Bluetooth and IEEE 802.11g radios both operate in the 2.4GHz band. Although the 7535 G2 includes features to minimize interference, performance of the system will not be optimal if you use both radios simultaneously. Typically, when both radios operate in the 7535 G2 at the same time, they cannot transmit simultaneously—this has a negative impact on overall system throughput. To minimize the impact on the backbone 802.
PAGE 224
Chapter 6: Peripheral Devices & Accessories Wiring Guidelines The most effective way to mount the picker cradle is to use the four #8-32 threaded inserts on the rear of the unit. Bolts must not extend more than 10mm (3/8") into the cradle. To accommodate the service loop of the connector cable, leave a 4" clearance at the bottom of the cradle. Leave a 7" (minimum) clearance at the top of the cradle to allow easy removal of the hand-held.
PAGE 225
Chapter 6: Peripheral Devices & Accessories Powered Cradle Installation In High Voltage Vehicles longer lock the 7535 G2 securely in the cradle. For replacement parts and instructions contact Psion Teklogix. Partial disassembly is required. 6.11.5 Powered Cradle Installation In High Voltage Vehicles Warning: Voltages exceeding 60VDC are considered hazardous.
PAGE 226
Chapter 6: Peripheral Devices & Accessories Powered Cradle Installation 6.11.6 Powered Cradle Installation The powered cradle option is designed to allow the 7535 G2 to be powered by a vehicle battery. The battery installed in the 7535 G2 is also recharged by the vehicle battery. This option accepts DC power sources over the range 12V to 80V. The 7535 G2 picker cradle can be ordered with the powered cradle option installed, or it can be retrofitted later at an authorized Psion Teklogix service depot.
PAGE 227
Chapter 6: Peripheral Devices & Accessories Wiring Vehicle Power To The Cradle 6.11.7 Wiring Vehicle Power To The Cradle A 1.8 meter (6 foot) extension power cable (P/N 13985-302 or 13985-301) is supplied with your power cradle. This cable should be wired to a filtered, fused (maximum 10A) accessory supply on the vehicle. The power cradle draws no more than 8A (less if the accessory supply is greater than 12V). Any additional wiring, connectors or disconnects used should be rated for at least 10A.
PAGE 228
Chapter 6: Peripheral Devices & Accessories Tether Adaptor Cables 6.12 Tether Adaptor Cables The following generic interface tether cables are available in addition to the dedicated cables provided for external scanners as described in “External Bar Code Readers” on page 179: • CA1010 JB5 to DE9 RS-232 Serial Cable: Straight through wiring. • CA1015 JB5 to DE9 RS-232 Serial Cable: Null modem (signal lines are crossed-over). • CA1020 JB5 to Type B USB: Connects to USB devices with Type B receptacles.
PAGE 229
7 SPECIFICATIONS 7.1 7535 G2 Hand-Held Computer Specifications . 7.1.1 Hardware . . . . . . . . . . . . . . . 7.1.2 Software . . . . . . . . . . . . . . . 7.1.3 Approvals. . . . . . . . . . . . . . . 7.2 Radio Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .201 .201 .203 .204 .204 7.
PAGE 230
200 Psion Teklogix 7535 G2 Hand-Held Computer User Manual
PAGE 231
Chapter 7: Specifications 7535 G2 Hand-Held Computer Specifications 7.1 7535 G2 Hand-Held Computer Specifications Note: Performance specifications are nominal and subject to change without notice. 7.1.1 Hardware Physical Dimensions • • 102mm width x 62.5mm depth x 260mm (4.0 in x 2.5 in x 10.2 in) length. Keypad area: 75.5mm width x 36mm (3 in x 1.4 in) depth. Weight • • With battery 647g (22.83 oz.) With pistol grip add 86.4g (3.05 oz.) User Interface Color Touchscreen Display: 8.9 cm (3.5 in.
PAGE 232
Chapter 7: Specifications Hardware Indicators And Controls: Multi-colour LEDs indicate battery status, application, and radio transmit/receive, user applications. Internal 95dB beeper with volume control. Power • • • • • • • • • • 7.4V @ 1900mAh Li-ion rechargeable battery. Intelligent fast charge. 8-hour battery operation (5 scans, transmit & receive/min.). Built-in gas gauge & performance monitor. Quick swap battery packs. Built-in fast charger (2 hour typical recharge).
PAGE 233
Chapter 7: Specifications Software Environmental Guaranteed Operating: -10°C to +50°C (14°F to 122°F) Temperature Range: Long exposure to temperatures below -40°C (-40°F) may damage the screen and main battery. Prolonged exposure to temperatures above +60°C (+140°F) will damage the main battery and temperatures above +70°C (+158°F) may damage the unit. Storage Temperature: -25°C to +60°C (-13°F to 140°F) Rain And Dust Resistance: IEC 529, classification IP65.
PAGE 234
Chapter 7: Specifications Approvals 7.1.3 Approvals Safety: UL 1950-1, CSA C22.2 No950, LVD EN60950 EMC: FCC Part 15 Class B, EMC Directive Class B Laser: IEC 60825-1 Ed. 2.0 Class 2 CDRH 21 CFR 1040 Class II RoHS compliant: 7.2 EU Directive 2002/95/EC Radio Specifications Model RA2043 (Motorola): 802.
PAGE 235
Chapter 7: Specifications Internal Scanner Port Channels FCC: 11 ETSI: 13 TELEC: 13 RX Sensitivity -96dBm @ 1Mbps, -90dBm @ 11Mbps, -94dBm @ 6Mbps, -75dBm @ 54Mbps Data Rates 802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11b: 1, 2, 5.5, 11 Mbps Bluetooth Radio Embedded (920 kbps serial interface) Bluetooth Version Ver 2.0 compliant (features Adaptive Frequency Hopping for better co-existence with 802.11 radio and Enhanced Data Rate (EDR) for up to 3Mbps data rate).
PAGE 236
Chapter 7: Specifications RFID Applications code scanner 7.4 1D Imagers: EV15, linear, short range 2D Laser Scanner: SE2223 2D decoded PDF417 raster 2D Imagers: SX5400 Imager RFID Applications • RD7950 Integrated UHF RFID Reader Psion Teklogix RFID File System Multi-protocol support 7.5 External Scanners 7.6 Supported Types Decoded and Non-Decoded 5V only. Interface Via tether port.
PAGE 237
Chapter 7: Specifications SE1200 High Performance And Long Range Specifications Symbologies Ambient Light Shock Vibration UPC (E&A), EAN, RSS, Code 39, Code 128, UCC/EAN 128, ISBN, ISBT, Interleaved, Matrix, Industrial and Standard 2 of 5, Codabar, Code 93/93i, Code 11, MSI, Plessey, Telepen, PDF417, Micro PDF417 Works in any lighting conditions, from 0 to 100,000 lux 2000G, 0.7ms, half sinus, 3 axes 50G r.m.s 7.6.1.
PAGE 238
Chapter 7: Specifications SE1200 High Performance And Long Range Specifications Parameter Symbologies Supported Programmable Parameters Ambient Light: SE1200HP UPC/EAN, Code 128, Code 39, Code 93, I 2 of 5, Discrete 2 of 5, Codabar, MSI UCC/EAN 128. Laser On Time, Aim Duration, Power Mode, Trigger Mode, Bidirectional Redundancy, Symbology types/lengths, Data formatting. Artificial: 450 ft. candles (4844 Lux). Sunlight: 10000 ft. candles (107,640 Lux). Laser Output Power 0.
PAGE 239
Chapter 7: Specifications SE1200 Advanced Long Range And SE2223PDF Specifications 7.6.3 SE1200 Advanced Long Range And SE2223PDF Specifications Parameter Type Light Source Scan Rate SE1200ALR Laser Class 2 Visible Laser Diode 650 nm 35 (± 5) scans/sec (bi-directional) Scan Angle/Field of View 13º± 2º Scan Patterns Minimum Print Contrast Linear Minimum 40% absolute dark/light reflectance measured at 650 nm. SE2223PDF Laser Class 2 Visible Laser Diode 650 nm 590 scan/sec. 22 frames/sec.
PAGE 240
Chapter 7: Specifications SE1200 Advanced Long Range And SE2223PDF Specifications 7.6.3.1 SE1200 And SE2223 Decode Zones Table 7.1 Decode Zones - HP, LR, And ALR Bar Code (mil) Read Distance High Performance Min (inches) Max (inches) Long Range Min (inches) Max (inches) Min (inches) Max (inches) 5.0 3.0 4.5 7.5 3.0 8.5 10.0 2.5 12.5 13.0 17.5 15.0 2.5 18.5 8.5 33.5 20.0 50.0 20.0 2.5 20.5 9.5 38.5 30.0 60.0 40.0 3.0 29.5 9.5 79.5 30.0 98.0 55.0 3.5 35.5 9.5 89.
PAGE 241
Chapter 7: Specifications SE1224HP Specifications 7.6.4 SE1224HP Specifications Parameter Type Light Source Scan Rate Scan Angle/Field of View Scan Patterns Minimum Print Contrast SE1224HP Ambient Light: Laser Class 2 Visible Laser Diode 650 nm 35 (± 5) scans/sec (bi-directional) 42º (typical), 30º (narrow) Linear Minimum 25% absolute dark/light reflectance measured at 650 nm. UPC/EAN, Code 128, UCC/EAN 128, RSS, Code 39, Code 93, I 2 of 5, Discrete 2 of 5, Codabar, MSI.
PAGE 242
Chapter 7: Specifications SE1524ER – Extended Range Scanner 7.6.4.1 SE1224HP Decode Zones 7.6.5 SE1524ER – Extended Range Scanner Parameter Type Light Source Scan Rate Scan Angle/Field of View Scan Patterns Minimum Print Contrast Symbologies Supported 212 SE1524ER Laser Class 2 Visible Laser Diode 650 nm 35 (±5) scans/sec (bi-directional). 13.5° ±0.7° Linear Minimum 25% absolute dark/light reflectance measured at 650 nm. UPC/EAN, Code 128, UCC.
PAGE 243
Chapter 7: Specifications SE1524ER – Extended Range Scanner Parameter Programmable Parameters Ambient Light: SE1524ER Laser On Time, Aim Duration, Power Mode, Trigger Mode, Bi-directional Redundancy, Symbology types/lengths, Data formatting. Artificial: 450 ft. candles (4,844 Lux) Sunlight: 4,000 ft. candles (86,112 Lux). Laser Output Power (peak) 1.26mW 7.6.5.1 SE1524ER Decode Zones Figure 7.
PAGE 244
Chapter 7: Specifications SE1524ER – Extended Range Scanner Figure 7.
PAGE 245
Chapter 7: Specifications SX5400* Imager Specifications 7.6.6 SX5400* Imager Specifications Optical Resolution 752H x 480V Field of view at 160mm 120mm (H) x 78mm (V) 41.1° (H) x 27.4° (V) Pitch angle ±45° Skew angle ±45° Ambient light 0 to 100,000 lux (full sunlight) 300 lux nominal Minimum contrast 10% Targeting Intuitive range finding 626 nm LED Self Illumination Red LED (standard) Supply voltage 5 V ± 10% Power supply 3.6 Volt DC nominal (2.7 - 5 Volts DC) Connectivity USB 1.
PAGE 246
Chapter 7: Specifications External Scanner Specifications 7.6.6.1 SX5400 Imager Performance The table below presents the typical performance of the SX5400 Imager at 300 lux (@ 160mm focus when using Grade A photographic-quality bar codes). Shown are the average near, far, and Depth of Reading (DOR) numbers. Symbology Size (mil) Near Avg. (inches) Far Avg. (inches) DOR Avg. (inches) C39 7.5 4.0 7.0 3.0 C39 10 2.75 9.25 6.5 C39 15 2.25 11.0 8.75 PDF6.6 6.6 4.0 6.5 2.5 PDF10 10 3.
PAGE 247
Chapter 7: Specifications PowerScan® LR and XLR Industrial Scanner Specifications Electrical Operating voltage 4 VDC to 14 VDC Operating current - nominal Undecoded: 75 mA @ 5 VDC Decoded: 100 mA @ 5 VDC Idling current - low power mode 50 µA @ 5 VDC Optical Light source Extra bright 650 nm Visible Laser Diode (VLD) Scan System Frictionless lifetime flexure mechanism Rate 35 scans/sec nominal Depth of field - Long Range Paper Labels (decoded) 7.
PAGE 248
Chapter 7: Specifications PowerScan® LR and XLR Industrial Scanner Specifications Reflective Labels (decoded) 40 mil 40 to 180 in (102 to 457 cm) 70 mil 80 to 300 in (2032 to 762 cm) 100 mil 80 to 432 in (203 to 1097 cm) Print Contrast Ratio 25% minimum Pitch ± 65° Skew ± 55° Ambient Light Immunity Artificial light: 1200 ft. candles. Sunlight: 8000 ft. candles.
PAGE 249
Chapter 7: Specifications PowerScan Standard Range Scanner Specifications Laser Classification IEC 60825-1 Ed. 2.0 CDRH 21 CFR 1040 Class II 7.7.2 PowerScan Standard Range Scanner Specifications Communication Undecoded Standard and Intermec-compatible. Mechanical Dimensions 6.9 x 11.2 x 18.3 cm (2.7 x 4.4 x 7.2 in) Weight Scanner - 280 g (9.9 ozs) Cable (82.3 cm 32 in) - 176 g (6.
PAGE 250
Chapter 7: Specifications PowerScan Standard Range Scanner Specifications 10 mil 0.2 to 5.5 in (0.5 to 14 cm) Print Contrast Ratio 25% minimum Pitch ± 65° Skew ± 55° Ambient Light Immunity Artificial light: 1200 ft. candles. Sunlight: 8000 ft. candles.
PAGE 251
Chapter 7: Specifications RD7950 Integrated UHF RFID Reader Safety/Regulatory Electrical Complies to: Gost R; TUV; UL; cUL Emissions Complies to: FCC-A;EN55022-B BCIQCNS13438; AS/NZS3548; VCCI-B Laser Classification IEC 60825-1 Ed. 2.0 CDRH 21 CFR 1040 Class II 7.8 RD7950 Integrated UHF RFID Reader For detailed RD7950 specifications, please see the RD7950 UHF RFID Reader Quick Reference Guide (P/N 8000056). 7.
PAGE 252
PAGE 253
APPENDIX A PORT PINOUTS A.1 Tether Port Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 A.2 Docking Station Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 A.3 Battery Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 254
PAGE 255
Appendix A: Port Pinouts Tether Port Pinout A.1 Tether Port Pinout The tether port connector incorporates multiplexed undecoded scanner, decoded scanner, RS-232 serial, and USB interfaces. In order for it to operate, a special wiring scheme is needed. If you have a need to create cables for the tether port, contact a Psion Teklogix representative and request document #1010032 “Instruction Tether Port Termination”.
PAGE 256
Appendix A: Port Pinouts Battery Contacts A.3 Battery Contacts These contacts represent right to left numbering with the docking port pointing toward you, and the battery contacts facing upward.
PAGE 257
Appendix A: Port Pinouts Battery Contacts Figure A.1 JB5 To USB Type B Cable - P/N CA1020 (Mates with USB devices that incorporate Type B receptacles) Figure A.
PAGE 258
PAGE 259
B APPENDIX SCU FOR RA2041 802.11B/G RADIO B.1 SCU Tabs . . . . . . . . . . . . . . . . . . . B.1.1 Main . . . . . . . . . . . . . . . . B.1.2 Profile . . . . . . . . . . . . . . . . B.1.3 Status . . . . . . . . . . . . . . . . B.1.4 Diags . . . . . . . . . . . . . . . . B.1.2.1 SCU Security Capabilities. B.1.2.2 SCU EAP Types . . . . . . B.1.2.3 EAP Credentials . . . . . . B.1.2.4 ThirdPartyConfig . . . . . B.1.5 Global. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 260
PAGE 261
Appendix B: SCU For RA2041 802.11b/g Radio SCU Tabs B.1 SCU Tabs This appendix provides details about each tab in the Summit Client Utility (SCU). For quick, step-by-step setup instructions, refer to “Summit Client Utility (SCU) For RA2041 802.11b/g Radio” on page 28. The following sections provide a detailed description of each of the tabs available in the SCU—Main (below), Profile (page B-4), Status (page B-9), Diags (page B-9), and Global (page B-10). B.1.
PAGE 262
Appendix B: SCU For RA2041 802.11b/g Radio SCU Tabs • • B.1.2 Driver and SCU: These fields display the version of the device driver and the SCU that are running on the 7535 G2. About SCU: This box provides details about the SCU software. Profile The Profile tab allows you to define radio and security settings that are stored in the registry as part of the configuration profile. The profile you create and save is listed in the Active Profile drop-down menu in the Main tab.
PAGE 263
Appendix B: SCU For RA2041 802.11b/g Radio SCU Tabs The following table describes the options in the Radio attributes, Encryption, and EAP Type drop-down menus: Table B.1 Radio, Encryption, And EAP Menus Radio Attribute Description Value Default SSID Service set identifier (SSID) for Maximum of 32 characters. WLAN to which the radio connects. None Client Name Name assigned to radio & 7535 G2 into which it is installed. None Maximum of 16 characters. Power Save Power save mode for radio.
PAGE 264
Appendix B: SCU For RA2041 802.11b/g Radio SCU Tabs Table B.1 Radio, Encryption, And EAP Menus Radio Attribute • Description Value Default Credentials Authentication credentials for the selected EAP type. Refer to “EAP Credentials” on page B-7. User: Username or Domain/User- None name (up to 64 characters). Password: up to 64 characters. For PEAP: CA Cert–CA server certificate filename. Encryption Type of encryption used to protect transmitted data.
PAGE 265
Appendix B: SCU For RA2041 802.11b/g Radio SCU Tabs • PEAP: Provides secure user authentication by using a TLS tunnel to encrypt EAP traffic. Two different inner methods are used with PEAP: - EAP-MSCHAPV2, resulting in PEAP-MSCHAP: This is appropriate for use against Windows Active Directory and domains. - EAP-GTC, resulting in PEAP-GTC: This is for authentication with one-time passwords (OTPs) against OTP databases such as SecureID.
PAGE 266
Appendix B: SCU For RA2041 802.11b/g Radio SCU Tabs • • If the credentials are not specified in the profile, when the radio tries to associate using that profile, you will be prompted to enter the credentials. When prompted, you can enter valid credentials, enter invalid credentials, or cancel the operation. - If you enter valid credentials and tap OK, the radio will associate and authenticate.
PAGE 267
Appendix B: SCU For RA2041 802.11b/g Radio SCU Tabs B.1.3 Status The Status tab provides status information including IP address and MAC address for the client radio, IP address and MAC address for the AP, signal strength, channel, transmit power and data rate. B.1.4 Diags Ping Address Ping Results Use the Diags tab as a troubleshooting tool.
PAGE 268
Appendix B: SCU For RA2041 802.11b/g Radio SCU Tabs • • • B.1.5 Release/Renew: Obtains a new IP address through DHCP and logs all activity in the output area. Start Ping: Starts a continuous ping to the address in the text box next to this button. This is a toggle button so when you tap on it, it changes to Stop Ping. Closing this window or tapping on another button also stops the ping.
PAGE 269
Appendix B: SCU For RA2041 802.11b/g Radio SCU Tabs Table B.2 Global Tab Global Setting Description Value Default Roam Trigger If RSSI from AP is less than roam dBm: -50, -55, -60, -65, -75 trigger value, radio performs roam scan -70, -75, Custom or probes for an AP with stronger signal. Roam Delta Amount by which second AP’s RSSI must exceed the moving average RSSI for the current AP before the radio will attempt to roam to a second AP.
PAGE 270
Appendix B: SCU For RA2041 802.11b/g Radio SCU Tabs Table B.2 Global Tab Global Setting Description Default WMM Use Wi-Fi Multimedia Extensions, also On, Off know as WMM. Off TX Diversity Defines how to handle antenna diversity when transmitting data to AP. -Main only: Use main antenna only. -Aux only: Use auxiliary antenna only. -On: Use diversity. Main only RX Diversity Defines how to handle antenna diversity when receiving data from AP. -On-Start on Main: On startup, use main antenna.
PAGE 271
Appendix B: SCU For RA2041 802.11b/g Radio SCU Tabs Table B.2 Global Tab Global Setting Description Value Default Auth Timeout Specifies the number of seconds that An integer from 3 to 60. 8 the software will wait for an EAP authentication request to succeed or fail. If authentication credentials are specified in the active profile and the authentication times out, then association will fail.
PAGE 272
PAGE 273
C APPENDIX BAR CODE SETTINGS C.1 Bar Code Settings. . . . . . . . . . . . . . . . . . C.1.1 Scanner Options . . . . . . . . . . . . . C.1.2 Restoring Default Settings . . . . . . . . C.2 Decoded (Internal) Scanners . . . . . . . . . . . . C.2.1 Options . . . . . . . . . . . . . . . . . . C.2.2 Decoded (Internal) Advanced Options . . C.2.3 Decoded (Internal) 2D Scanning Options C.2.4 Decoded (Internal) Data Options . . . . . C.2.5 Code 39 . . . . . . . . . . . . . . . . . . C.2.6 Code 128 . . . . . . . . .
PAGE 274
Appendix C: Bar Code Settings C.3.5 EAN 13 . . . . . . . . . . . . . . . . . . C.3.6 EAN 8 . . . . . . . . . . . . . . . . . . . C.3.7 UPC A . . . . . . . . . . . . . . . . . . . C.3.8 UPC E Settings . . . . . . . . . . . . . . C.3.9 UPC/EAN Shared Settings . . . . . . . . C.3.10 Code 93. . . . . . . . . . . . . . . . . . C.3.11 Codabar. . . . . . . . . . . . . . . . . . C.3.12 MSI Plessey . . . . . . . . . . . . . . . C.3.13 Code 11. . . . . . . . . . . . . . . . . . C.3.14 Interleaved 2 of 5. . . . . . .
PAGE 275
Appendix C: Bar Code Settings C.4.17 2D QR Code . . . C.4.18 2D Maxicode . . C.4.19 2D Aztec . . . . . C.4.20 Postal: PlaNET . C.4.21 Postal: PostNET . C.4.22 Postal: Australian C.4.23 Postal: Japanese . C.4.24 Postal: Korean . . C.4.25 Postal: Royal. . . C.4.26 Postal: Kix . . . . C.4.27 Postal: Canadian . C.5 Non-Decoded Scanners . . . C.5.1 Options . . . . . . C.5.2 Code 39 . . . . . . C.5.3 Code 128 . . . . . C.5.4 EAN 13 . . . . . . C.5.5 EAN 8 . . . . . . . C.5.6 UPC A. . . . . . . C.5.7 UPC E . . .
PAGE 276
PAGE 277
Appendix C: Bar Code Settings Bar Code Settings Scanner Options C.1 Bar Code Settings The Teklogix Scanners icon in the Control Panel provides dialog boxes in which you can tailor bar code options and choose the bar codes your scanner will recognize. The parameters are preset with the default settings of the decoded scanner installed in the unit. For a listing of available scanners and their specifications, please refer to Chapter 7: “Specifications”. Figure C.1 Teklogix Scanners Icon C.1.
PAGE 278
Appendix C: Bar Code Settings Bar Code Settings Restoring Default Settings The symbologies listed change to reflect the scanner you choose and the bar codes it supports. Always defer to your bar code scanner’s programming manual when in doubt about the availability or settings for any parameter. Note: Your 7535 G2 comes preconfigured from the factory for internal scanner types. The type of scanner installed can be determined from the System icon in the Control Panel, under the System Properties tab.
PAGE 279
Appendix C: Bar Code Settings Bar Code Settings Restoring Default Settings • Press and hold the stylus on a symbology (e.g., Code 128) to display a pop up a menu. • Choose Default subtree to reset only the parameters in the symbology you selected, or choose Default all settings to reset all scanner parameters to default settings. To reset a single parameter to its default setting: • Press and hold the stylus on the parameter you want to reset.
PAGE 280
Appendix C: Bar Code Settings Decoded (Internal) Scanners Options C.2 Decoded (Internal) Scanners • C.2.1 Tap on the Scanner drop-down menu, and choose Decoded (internal). Options Note: Some options are available only for specific scanners. Refer to the option names in this section for scanner model identification. Dot Time (msec) The value selected for Dot Time (msec) determines (in milliseconds) how long the targeting dot remains on before the scanner switches to a normal scan sweep.
PAGE 281
Appendix C: Bar Code Settings Decoded (Internal) Scanners Decoded (Internal) Advanced Options C.2.2 Decoded (Internal) Advanced Options Continuous Scan Mode Setting this parameter to on keeps the laser on and continuously decoding as long as the scanner button is pressed and held down. Minimum Cancel Time The value assigned to this parameter determines the time delay before the scanner is turned off, once the scanner trigger or button is released.
PAGE 282
Appendix C: Bar Code Settings Decoded (Internal) Scanners Decoded (Internal) Advanced Options Linear Security Level This parameter allows you to select the security level appropriate for your bar code quality. There are four levels of decode security for linear code types (e.g., Code 39, Interleaved 2 of 5). Higher security levels should be selected for decreasing levels of bar code quality. As security levels increase, the scanner’s decode speed decreases.
PAGE 283
Appendix C: Bar Code Settings Decoded (Internal) Scanners Decoded (Internal) 2D Scanning Options Scan Angle This option allows you to choose from two scan angles: Normal Angle or Alternate Angle. Choosing Normal Angle allows the normal operation for scanning long range and short range. Choosing Alternate Angle widens the beam to allow scanning of long bar codes at short range but at the cost of long range scanning. C.2.
PAGE 284
Appendix C: Bar Code Settings Decoded (Internal) Scanners Code 39 Prefix [P], Suffix [S1] And Suffix [S2] A prefix and/or one or two suffixes may be appended to scan data for use in data editing. When you double-tap on these parameters, dialog boxes are displayed in which you can enter a value from 0 to 255.
PAGE 285
Appendix C: Bar Code Settings Decoded (Internal) Scanners Code 39 Code 32 Prefix Note: “Convert to Code 32” must be enabled in order for this parameter to function. When this parameter is enabled, the prefix character “A” is added to all “Code 32” bar codes. Set Length L1 And Set Length L2 Lengths for “Code 39” can be set for Any length, Length within a range, One discrete length or Two discrete lengths. The length of a code refers to the number of characters (i.e.
PAGE 286
Appendix C: Bar Code Settings Decoded (Internal) Scanners Code 39 Transmit Check Digit If the check digit is to be transmitted with the data, this parameter must be enabled. Full ASCII If this parameter is enabled, the characters +, %, and / are used as escape characters. The combination of an escape character and the next character is converted to an equivalent ASCII character.
PAGE 287
Appendix C: Bar Code Settings Decoded (Internal) Scanners Code 128 Minimum Size And Maximum Size When a value is assigned to these parameters, only bar code lengths that fall between the minimum and maximum value can be decoded. If values are assigned to these parameters, a Field Size value is not required. Add/Remove Data Prefix Char This character, if non-zero, is added before a successfully decoded bar code. Press the key you want to insert in the dialog box attached to this parameter.
PAGE 288
Appendix C: Bar Code Settings Decoded (Internal) Scanners EAN 13 Decode Performance If this parameter is set to on, one of three decode levels assigned to the Decode Performance Level parameter can be selected. Decode Perf. Level This parameter provides three levels of decode performance or “aggressiveness” for Code 128 symbols. Increasing the performance level reduces the amount of required bar code orientation, allowing you to scan at an angle horizontal to the bar code.
PAGE 289
Appendix C: Bar Code Settings Decoded (Internal) Scanners UPC A Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.2.9 UPC A Enabled Set this parameter to on to enable “UPC A”. UPC-A, Check Digit If you enable this parameter, the check digit is included with the decoded bar code data.
PAGE 290
Appendix C: Bar Code Settings Decoded (Internal) Scanners UPC/EAN Shared Settings UPC-E And UPC-E1 Preamble When you double-tap on one of these parameters, a dialog box is displayed where you can choose one of three options for lead-in characters for UPC-E and UPC-E1 symbols transmitted to the host device: System Char—system character transmitted with the data, Country Code and System Char—both the country code (“0” for USA) and system character are transmitted with the data, or None—no preamble is transmi
PAGE 291
Appendix C: Bar Code Settings Decoded (Internal) Scanners Code 93 Supp. Redundancy With “Autodiscriminate” selected in the Supplementals parameter, Supp. Redundancy adjusts the number of times a symbol without supplementals is decoded before transmission. When you double-tap on this parameter, a dialog is displayed in which you can enter a value between 2 and 20.
PAGE 292
Appendix C: Bar Code Settings Decoded (Internal) Scanners Codabar selected lengths. Length within a range allows you to decode a code type within a specified range from 4 to 55. Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.2.13 Codabar Enabled Set this parameter to on to enable “Codabar”.
PAGE 293
Appendix C: Bar Code Settings Decoded (Internal) Scanners MSI Plessey Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.2.14 MSI Plessey Enabled Set this parameter to on to enable “MSI Plessey”. Set Length L1 And Set Length L2 Lengths for “MSI Plessey” can be set for Any length, Length within a range, One discrete length or Two discrete lengths. The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s).
PAGE 294
Appendix C: Bar Code Settings Decoded (Internal) Scanners Interleaved 2 of 5 Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.2.15 Interleaved 2 of 5 Enabled Set this parameter to on to enable “Interleaved 2 of 5”. Set Length L1 And Set Length L2 Lengths for “Interleaved 2 of 5” can be set for Any length, Length within a range, One discrete length or Two discrete lengths. The length of a code refers to the number of characters (i.e.
PAGE 295
Appendix C: Bar Code Settings Decoded (Internal) Scanners Discrete 2 of 5 C.2.16 Discrete 2 of 5 Enabled Set this parameter to on to enable “Discrete 2 of 5”. Set Length L1 And Set Length L2 Lengths for “Discrete 2 of 5” can be set for Any length, Length within a range, One discrete length or Two discrete lengths. The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s).
PAGE 296
Appendix C: Bar Code Settings Decoded (Internal) Scanners Composite Enable RSS Expanded “RSS Expanded” uses the same application identifiers as UCC/EAN-128 codes but it can be split into sections and stacked several rows high, reducing the length of the symbol, while increasing the capacity of data that can be stored. “RSS Expanded” code can be omnidirectionally scanned. Length Restriction Refer to “Length Restriction” on page C-14 for details.
PAGE 297
Appendix C: Bar Code Settings Decoded (Internal) Scanners Micro PDF-417 Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.2.20 Micro PDF-417 Enabled Setting this parameter to on enables “2D Micro PDF-417” bar code scanning. Micro PDF417 is a multi-row symbology that is useful for applications requiring greater area efficiency but lower data capacity than PDF-417.
PAGE 298
Appendix C: Bar Code Settings Decoded (Intermec ISCP) Decoded (ISCP) Options C.3 Decoded (Intermec ISCP) • C.3.1 Tap on the Scanner drop-down menu, and choose Decoded (Intermec ISCP). Decoded (ISCP) Options Laser On Time The value assigned to this parameter determines how long the laser will remain on when the scan button or trigger is pressed. Double-tapping on this parameter displays a dialog box in which you can enter a value between 1 and 10 seconds. C.3.
PAGE 299
Appendix C: Bar Code Settings Decoded (Intermec ISCP) Code 39 Low Power Timeout To extend laser life, you can select the time the scanner remains active following a successful decode. The scanner wakes from low power mode when a bar code is scanned—a successful decode restores normal blinking. When you double-tap on this parameter, a dialog box is displayed in which you can choose a value of 30 sec, 1 min, 2 min, or 3 min.
PAGE 300
Appendix C: Bar Code Settings Decoded (Intermec ISCP) Code 39 Full ASCII If this parameter is enabled, the characters +, %, and / are used as escape characters. The combination of an escape character and the next character is converted to an equivalent ASCII character. Reading Range Determines the reading distance from which a bar code can be successfully scanned. The default setting, Extended, allows for increased reading distance.
PAGE 301
Appendix C: Bar Code Settings Decoded (Intermec ISCP) Code 128 Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.3.4 Code 128 Enabled Setting this parameter to on enables “Code 128”. GS1-128 “GS1-128” is the GS1 implementation of the Code 128 barcode specification. The former correct name was UCC/EAN-128. GS1-128 Identifier “GS1-128 Identifier” allows the AIM ID " ]C1" for EAN 128 to be transmitted or removed. By default, this identifier is transmitted if EAN 128 is enabled.
PAGE 302
Appendix C: Bar Code Settings Decoded (Intermec ISCP) EAN 13 code will be transmitted as a single code. If both codes in a pair are detected, they will be concatenated provided that “ISBT Concat Any Pair” (see below) is enabled. ISBT Concat Any Pair Enabling this parameter causes all code pairs that can be, to be concatenated even if they do not comply with Section 4.1 of the “ISBT 128 Bar Code Symbology and Application Specification for Labeling of Whole Blood and Blood Components” (June 2000, Version 1.
PAGE 303
Appendix C: Bar Code Settings Decoded (Intermec ISCP) EAN 8 Transmit Check Digit If the check digit is to be transmitted with the data, this parameter must be enabled. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.3.6 EAN 8 Enabled Set this parameter to on to enable “EAN 8”. Transmit Check Digit If the check digit is to be transmitted with the data, this parameter must be enabled. Convert To EAN 13 If this parameter is enabled, an EAN 8 bar code is converted to EAN 13.
PAGE 304
Appendix C: Bar Code Settings Decoded (Intermec ISCP) UPC E Settings C.3.8 UPC E Settings Enabled Set this parameter to on to enable “UPC E”. Enable UPC-E1 Set this parameter to on to allow “UPC-E1” (zero suppressed) bar code scans. Transmit Check Digit If the check digit is to be transmitted with the data, this parameter must be enabled. Transmit Number System If this parameter is enabled, the number system digit is transmitted with the decoded bar code data.
PAGE 305
Appendix C: Bar Code Settings Decoded (Intermec ISCP) Code 93 Addendum Add-on 2 And Addendum Add-on 5 Enabling these parameters sets the length of the addendum bar code to either 2 or 5 characters. Addendum Security If you tap on “Addendum Security”, a dialog box is displayed in which you can define the security level of add-on 2 or add-on 5 with a value from 0 to 100. As security levels increase, the scanner decode speed decreases.
PAGE 306
Appendix C: Bar Code Settings Decoded (Intermec ISCP) Codabar C.3.11 Codabar Enabled Set this parameter to on to enable “Codabar”. Start/Stop Transmit Codabar can use the following sets of characters as start and stop characters: a, b, c, d A, B, C, D a, b, c, d, /, t, n, *, e DC1, DC2, DC3, DC4 Thus, when a set is chosen, the first and last digits of a Codabar message must be one of those characters and the body of the message should not contain these characters.
PAGE 307
Appendix C: Bar Code Settings Decoded (Intermec ISCP) MSI Plessey Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.3.12 MSI Plessey Enabled Set this parameter to on to enable “MSI”. Enable Plessy Set this parameter to on to enable “Plessy”. Check Digit Verification The available options for this parameter are MOD 10 Check and Double MOD 10 Check.
PAGE 308
Appendix C: Bar Code Settings Decoded (Intermec ISCP) Code 11 C.3.13 Code 11 Enabled Set this parameter to on to enable “Code 11”. Check Digit Verification The available options for this parameter are MOD 10 Check and Double MOD 10 Check.This parameter uses the specified algorithm of the option you've chosen to ensure the integrity of the symbol data before transmitting. If the data does not contain that algorithm, the data is not transmitted.
PAGE 309
Appendix C: Bar Code Settings Decoded (Intermec ISCP) Matrix 2 of 5 Note: French CIP (French pharmaceutical) is only used with bar codes containing 7 characters. Transmit Check Digit If the check digit is to be transmitted with the data, this parameter must be enabled. Set Length L1, Set Length L2, And Set Length L3 Lengths for “Interleaved 2 of 5” can be set from 0 to 255. The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s).
PAGE 310
Appendix C: Bar Code Settings Decoded (Intermec ISCP) Discrete 2 of 5 C.3.16 Discrete 2 of 5 Enabled Set this parameter to on to enable “Discrete 2 of 5”. Standard 2 of 5 Format This parameter allows you to choose a standard format – either Identicon (6 start/stop bars) or Computer Identics (4 start/stop bars). Check Digit Verification The available options for this parameter are Disabled and MOD 10 Check.
PAGE 311
Appendix C: Bar Code Settings Decoded (Intermec ISCP) RSS Code (Reduced Space Symbology) Format This parameter allows you to set the bar code character format to either ASCII or Numeric. Minimum Length Minimum lengths for the bar code can be set from 0 to 255. The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s). Length Restriction Refer to “Length Restriction” on page C-14 for details.
PAGE 312
Appendix C: Bar Code Settings Decoded (Intermec ISCP) Composite C.3.19 Composite Important: To successfully read this type of bar code, the two types of symbologies included in a composite bar code must be enabled. In addition, “Center Bar Code Only” must be disabled (see page C-43). A composite symbol includes multi-row 2D components making it compatible with linear and area CCD scanners along with linear and rastering laser scanners.
PAGE 313
Appendix C: Bar Code Settings Decoded (Intermec ISCP) PDF-417 Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.3.21 PDF-417 Enabled Set this parameter to on to enable “2D PDF-417”. Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.3.22 Micro PDF-417 Enabled Set this parameter to on to enable “2D Micro PDF-417”.
PAGE 314
Appendix C: Bar Code Settings Imager Codablock Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.3.23 Codablock Enable Codablock A Set this parameter to on to enable “Codablock type A”. Enable Codablock F Set this parameter to on to enable “Codablock type F”. Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.4 Imager • C.4.1 Tap on the Scanner drop-down menu, and choose Imager.
PAGE 315
Appendix C: Bar Code Settings Imager Imager Options Continuous Scan Mode Setting this parameter to on keeps image capture active and continuously decoding as long as the scanner button is pressed and held down. Center Barcode Only Note: This parameter must be disabled when reading Composite bar codes. When more than one bar code is visible in a single snap shot, this parameter allows you to specify that only the centre image within the imager framing marker be read.
PAGE 316
Appendix C: Bar Code Settings Imager Imager Advanced Options Dot Time (msec) The value selected for “Dot Time (msec)” determines (in milliseconds) how long the targeting dot remains on before the scanner begins capturing images. When you double-tap on this parameter, a dialog box is displayed in which you can enter a value of between 0 and 3000. A value of 0 disables the target dot. C.4.
PAGE 317
Appendix C: Bar Code Settings Imager Imager Advanced Options Auto Exposure Important: This parameter value should only be changed by qualified Psion Teklogix personnel. It should be left at the default value: on. Setting this parameter to on allows the imager to make automatic gain, integration and illumination adjustments based on ambient light before capturing the bar code. If the adjustment is insufficient, further adjustments are made automatically before another image is captured.
PAGE 318
Appendix C: Bar Code Settings Imager Code 39 Note: When decoding multiple bar codes in one image, the value assigned to ‘Decoder Timeout’ should be increased to 200ms/extra bar code after the first. Adaptive Windowing “Adaptive Windowing” is an advanced technique used to speed up bar code recognition in certain applications.
PAGE 319
Appendix C: Bar Code Settings Imager Code 128 Include Check If this parameter is enabled, the check digit is included with the decoded bar code data. Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.4.4 Code 128 Enabled Set this parameter to on to enable “Code 128. Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details.
PAGE 320
Appendix C: Bar Code Settings Imager EAN 8 Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.4.6 EAN 8 Enabled Set this parameter to on to enable “EAN 8”. Addendum Refer to “Addendum” on page 47. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.4.7 UPC A Enabled Set this parameter to on to enable “UPC A”. Addendum Refer to “Addendum” on page 47. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.4.
PAGE 321
Appendix C: Bar Code Settings Imager Code 93 C.4.9 Code 93 Enabled Set this parameter to on to enable “Code 93”. Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.4.10 Codabar Enabled Set this parameter to on to enable “Codabar”. Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.4.
PAGE 322
Appendix C: Bar Code Settings Imager RSS Code (Reduced Space Symbology) Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.4.12 RSS Code (Reduced Space Symbology) Enable Setting this parameter to on enables “RSS Code” scanning capability. Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.4.
PAGE 323
Appendix C: Bar Code Settings Imager Micro PDF-417 C.4.15 Micro PDF-417 Enabled Setting this parameter to on enables “Micro PDF-417” bar code scanning. Micro PDF-417 is a multi-row symbology that is useful for applications requiring greater area efficiency but lower data capacity than PDF-417. Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.4.
PAGE 324
Appendix C: Bar Code Settings Imager 2D Maxicode Inverse Video Mode Enabling this parameter allows the imager to read inverse bar codes—white symbols presented on a black background. Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.4.18 2D Maxicode Enabled Set this parameter to on to enable “2D Maxicode”. Length Restriction Refer to “Length Restriction” on page C-14 for details.
PAGE 325
Appendix C: Bar Code Settings Imager Postal: PostNET Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.4.21 Postal: PostNET Enabled Set this parameter to on to enable “Postal: PostNET”. Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.4.
PAGE 326
Appendix C: Bar Code Settings Imager Postal: Korean C.4.24 Postal: Korean Enabled Set this parameter to on to enable “Postal: Korean”. Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.4.25 Postal: Royal Enabled Set this parameter to on to enable “Postal: Royal”. Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.4.
PAGE 327
Appendix C: Bar Code Settings Non-Decoded Scanners Postal: Canadian Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.5 Non-Decoded Scanners Figure C.2 Non-Decoded Scanner Options • Tap on the Scanner drop-down menu, and choose Non-decoded. All the available bar code symbologies for this type of scanner can be selected in this tab.
PAGE 328
Appendix C: Bar Code Settings Non-Decoded Scanners Options C.5.1 Options • Tap the stylus on the + sign next to Options to display these parameters. Dot Time (msec) The value selected for “Dot Time (msec)” determines (in milliseconds) how long the targeting dot remains on before the scanner switches to a normal scan sweep. When you doubletap on this parameter, a dialog box is displayed in which you can enter a value from 0 to 3000. A value of 0 (zero) disables the target dot.
PAGE 329
Appendix C: Bar Code Settings Non-Decoded Scanners Code 39 Include Check If this parameter is enabled, the check digit is included with the decoded bar code data. AIAG Strip If this parameter is enabled, the AIAG data identifier is removed from each decoded Code 39 label. The data identifier occurs in the first position next to the Code 39 start character. It can be a single alphabetic character or a series of numeric digits followed by an alphabetic character.
PAGE 330
Appendix C: Bar Code Settings Non-Decoded Scanners Code 128 C.5.3 Code 128 Enabled Set this parameter to on to enable “Code 128” or off to disable it. Include Sym Setting “Include Sym” to on causes the group separator(s) and start code contained in this type of bar code to be displayed on the screen. Note: This option is available only when ‘EAN/UCC 128’ is selected. Variations When using Code 128, you can choose the bar code variation the scanner will recognize.
PAGE 331
Appendix C: Bar Code Settings Non-Decoded Scanners EAN 13 Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.5.4 EAN 13 Enabled Set this parameter to on to enable “EAN 13” or off to disable it. Enable Bookland EAN Setting this parameter to on allows your scanner to recognize Bookland EAN bar codes. Include Country If this parameter is enabled, the country code is included with the decoded bar code data.
PAGE 332
Appendix C: Bar Code Settings Non-Decoded Scanners EAN 8 Transmit Code ID Char A code ID character identifies the scanned bar code type. In addition to any single character prefix already selected, the code ID character is inserted between the prefix and the decoded symbol. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.5.5 EAN 8 Enabled Set this parameter to on to enable “EAN 8” or off to disable it.
PAGE 333
Appendix C: Bar Code Settings Non-Decoded Scanners UPC E Include Check If this parameter is enabled, the check digit will be included with the decoded bar code data. Addendum Important: Before “Addendum” can take effect, the “Short Code” parameter (see page C-56) must be enabled. Refer to “Addendum” on page C-59. Transmit Code ID Char A code ID character identifies the scanned bar code type.
PAGE 334
Appendix C: Bar Code Settings Non-Decoded Scanners Codabar Refer to “Addendum” on page C-59. Transmit Code ID Char A code ID character identifies the scanned bar code type. In addition to any single character prefix already selected, the code ID character is inserted between the prefix and the decoded symbol. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.5.8 Codabar Enabled Set this parameter to on to enable “Codabar” or off to disable it.
PAGE 335
Appendix C: Bar Code Settings Non-Decoded Scanners Code 11 Transmit Code ID Char A code ID character identifies the scanned bar code type. In addition to any single character prefix already selected, the code ID character is inserted between the prefix and the decoded symbol. Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.5.10 Code 11 Enabled Set this parameter to on to enable “Code 11”.
PAGE 336
Appendix C: Bar Code Settings Non-Decoded Scanners Interleaved 2 of 5 C.5.11 Interleaved 2 of 5 Enabled Set this parameter to on to enable “Interleaved 2 of 5”. MOD 10 Check If this parameter is enabled, the “MOD 10” check digit is calculated. This calculation is the same as the Code 39 MOD 10 check digit. ITF Check If this parameter is enabled, the ITF-14/16 MOD 10 check digit is calculated. Include Check If this parameter is enabled, the check digit is included with the decoded bar code data.
PAGE 337
Appendix C: Bar Code Settings Non-Decoded Scanners Discrete 2 of 5 Transmit Code ID Char A code ID character identifies the scanned bar code type. In addition to any single character prefix already selected, the code ID character is inserted between the prefix and the decoded symbol. Length Restriction Refer to “Length Restriction” on page C-14 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-15 for details. C.5.
PAGE 338
Appendix C: Bar Code Settings Non-Decoded Scanners IATA 2 of 5 C.5.14 IATA 2 of 5 Enabled Set this parameter to on to enable “IATA 2 of 5”. MOD 10 Check If this parameter is enabled, the MOD 10 check digit is calculated. ITF Check If this parameter is enabled, the ITF-14/16 MOD 10 check digit is calculated. Include Check If this parameter is enabled, the check digit is included with the decoded bar code data. Transmit Code ID Char A code ID character identifies the scanned bar code type.
PAGE 339
D APPENDIX TEKLOGIX IMAGERS APPLET D.1 Required Applets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 D.2 Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D.2.1 Predefined Presets . . . . . . . . . . . . . . . . . . . . . . D.2.2 Bar Code Predefined Presets . . . . . . . . . . . . . . . . . D.2.2.1 Bar Code Decoding Symbology Predefined Presets D.2.3 Bar Code Decoding Camera Predefined Presets . . . . . . . D.2.4 Image Capture Predefined Presets . . .
PAGE 340
Appendix D: Teklogix Imagers Applet D.4.14 Filter Tab – Manipulating Bar Code Data . . D.4.14.1 Modifying A Bar Code Setting . . . D.4.15 Translation Tab – Configuring Rules . . . . D.4.16 Advanced Tab . . . . . . . . . . . . . . . . D.4.16.1 File Locations For Captured Images D.4.16.2 Configuring Triggers . . . . . . . . D.5 Teklogix Scanners Applet . . . . . . . . . . . . . . . . D-2 Psion Teklogix 7535 G2 Hand-Held Computer User Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 341
Appendix D: Teklogix Imagers Applet Required Applets The Teklogix Imagers applet is used to create, modify, delete, and activate imager settings for imagers such as the SX5400. The principle uses of the applet are to decode bar codes and to capture images. A Demonstration Application is provided to demonstrate how the imager works. Refer to “Demo” on page 78 for details. D.
PAGE 342
Appendix D: Teklogix Imagers Applet Predefined Presets D.2.1 Predefined Presets Predefined presets are built into the imaging software and cannot be changed. The predefined presets allow you to use the imager to perform specified tasks without having to understand and set numerous variables. In almost all cases these predefined presets are sufficient. D.2.2 Bar Code Predefined Presets These presets encompass the majority of the most popular bar codes and their subtypes.
PAGE 343
Appendix D: Teklogix Imagers Applet Bar Code Decoding Camera Predefined Presets Postal This preset enables the decoding of all the postal symbologies that the imager can decode. D.2.3 Bar Code Decoding Camera Predefined Presets The following presets enable successful bar code image capture in almost all conditions. Note: It is recommended that the default preset be used whenever possible. Default This preset works in a wide range of conditions.
PAGE 344
Appendix D: Teklogix Imagers Applet Using The Teklogix Imagers Applet Low light near This preset is designed for dark conditions, it uses a longer exposure time and includes the flash. D.3 Using The Teklogix Imagers Applet D.3.1 Configuring The Image Capture Presets To configure the image capture presets, open the dialog box as follows: • • Tap on Start>Settings>Control Panel. Tap on the Teklogix Imagers icon, and if it’s not already selected, tap on the Imaging tab.
PAGE 345
Appendix D: Teklogix Imagers Applet Selecting A Camera • • D.3.2 Custom presets are marked as ‘RW’ read and write. One preset – either predefined or custom – is marked as ‘A’ active. Selecting A Camera If your 7535 G2 has more than one built-in camera, one camera must be selected for configuration. To select a camera: • • D.3.3 Tap on the Camera Presets drop-down menu to view the camera options. Choose a camera – specifically, Front Imager which is located at the top of the unit.
PAGE 346
Appendix D: Teklogix Imagers Applet Modifying A Custom Preset • Highlight a preset, and tap on the Add button. A screen like the sample below is displayed. • Type the name of the new preset in the dialog box. • Tap on OK to save your changes. The preset list is displayed; the new custom preset appears at the end of the list. It is marked as read and write. D.3.6 Modifying A Custom Preset The parameter values in a custom preset can be modified.
PAGE 347
Appendix D: Teklogix Imagers Applet Removing A Custom Preset • • Scroll through the parameter list until you reach the parameter that you want to change. For a parameter that can take a range of values: - Highlight the parameter, and then press the [SPACE] key or double-click on the parameter. - An associated dialog box containing the valid range of values for the parameter and the current setting like the sample screen following is displayed. - Type a value in the field provided.
PAGE 348
Appendix D: Teklogix Imagers Applet Selecting A Camera • Tap on the Barcoding tab. This window lists all the presets, both predefined and the custom. Presets are identified as follows: • • • Predefined presets are marked as read-only. For a description, review “Predefined Presets” on page D-4. Custom presets are marked as read and write. One preset – either predefined or custom – is marked as active. Note: The top portion of the window displays the bar code decoding camera presets.
PAGE 349
Appendix D: Teklogix Imagers Applet Setting The Active Preset D.4.2 Setting The Active Preset An active preset has an A to the right; in Figure D.1 on page 14, the active preset is Default. To set an active preset: • D.4.3 Highlight the preset, and tap on the Activate button. Viewing A Preset To view the parameter settings in a preset: • Highlight a preset, and tap on the View button. The associated preset window is displayed. • D.4.
PAGE 350
Appendix D: Teklogix Imagers Applet Modifying A Custom Preset A screen like the sample following is displayed. • Type the name of the new preset in the dialog box. • Tap on OK to save your changes. The preset list is displayed; the new custom preset appears at the end of the list. It is marked as read and write. D.4.5 Modifying A Custom Preset The parameter values in a custom preset can be modified. It is recommended that very few changes be made to a custom preset.
PAGE 351
Appendix D: Teklogix Imagers Applet Removing A Custom Preset • For a parameter that can take a range of values: - Highlight the parameter, and then press the [SPACE] key or double-click the parameter. - An associated dialog box containing the valid range of values for the parameter and the current setting like the sample screen following is displayed. - Type a value in the field provided.
PAGE 352
Appendix D: Teklogix Imagers Applet Setting The Active Preset Figure D.1 Viewing Bar Code Decoding Symbologies D.4.8 Setting The Active Preset An active preset has an A to the right; in Figure D.1 on page 14, the active preset is Default. To set an active preset: • D.4.9 Highlight the preset, and tap on the Activate button. Viewing A Preset To view the parameter settings in a preset: • D-14 Highlight a preset, and tap on the View button.
PAGE 353
Appendix D: Teklogix Imagers Applet Creating A Custom Preset The associated preset window is displayed. • Tap on the + sign to expand one of the lists so that you can view the parameter settings. D.4.10 Creating A Custom Preset A new custom preset is created by modifying a preset – either a predefined preset or an existing custom preset. To create a custom preset: • Highlight a preset, and tap on the Add button. A screen like the sample following is displayed.
PAGE 354
Appendix D: Teklogix Imagers Applet Modifying A Custom Preset D.4.11 Modifying A Custom Preset The parameter values in a custom preset can be modified. It is recommended that very few changes be made to a custom preset. To ensure that it will work reliably, it should be as close as possible to the original predefined preset. To change a parameter value: • Highlight the custom preset, and tap on the Edit button. • • • Tap on the + symbols to expand the lists and view the parameter settings.
PAGE 355
Appendix D: Teklogix Imagers Applet Removing A Custom Preset - Highlight the parameter and then press the [SPACE] key, or double-click on the parameter. Either method toggles between the two available values. • When you’ve completed your edits, tap on OK. The parameter list is displayed; the new value for the changed parameter is shown. • Tap on OK to exit to the preset list and save the changes. D.4.
PAGE 356
Appendix D: Teklogix Imagers Applet Filter Tab – Manipulating Bar Code Data • Tap on the Teklogix Imagers icon, and then tap on the Filter tab. D.4.14.1 Modifying A Bar Code Setting The rules for manipulating data from selected bar code symbologies can be modified. To change the settings for a symbology: • • • Tap on the + symbols to expand the lists and view the parameter settings. Scroll through the parameter list until you reach the parameter that you want to change.
PAGE 357
Appendix D: Teklogix Imagers Applet Translation Tab – Configuring Rules • For a parameter that takes a single character: - Highlight the parameter and then press the [SPACE] key, or double-click on the parameter. The following screen is displayed: • When you’ve completed your edits, tap on OK. D.4.15 Translation Tab – Configuring Rules Translation rules enable the automatic processing of bar code data. Up to 10 cases can be defined, each consisting of up to 10 sequential rules.
PAGE 358
Appendix D: Teklogix Imagers Applet Advanced Tab D.4.16 Advanced Tab D.4.16.1 File Locations For Captured Images To configure the location for saved images, open the dialog box as follows: • • Tap on Start>Settings>Control Panel. Tap on the Teklogix Imagers icon, and then tap on the Advanced tab. To define the location where imager files will be stored: D-20 • Tap on the File Location button. • • Select the folder name and file Type. Then enter the file Name.
PAGE 359
Appendix D: Teklogix Imagers Applet Teklogix Scanners Applet D.4.16.2 Configuring Triggers Viewing The Trigger Configuration The trigger on the 7535 G2 is configured using the Manage Triggers applet. The Teklogix Imagers applet provides a shortcut to the Manage Triggers applet. • • In the Advanced tab, tap on the Trigger Control button. To view all the triggers and the hardware devices that are configured to use them, tap in the checkbox next to Show all modules.
PAGE 360
PAGE 361
INDEX A Accepted Start Char C-28 accessories bar code readers, connecting 179 hand strap 16 picker cradle 193 pistol grip 18 Active Conn Tab 134 ActiveSync ASync profile 129 Adaptive Windowing C-46 adaptor cables, tether 198 Addendum C-32, C-47, C-48, C-61, C-59, C-60 Addendum Add-on 2 C-33 Addendum Add-on 5 C-33 Addendum Security C-33 Add Remove Data (bar code scanning) C-15 Prefix C-15 Strip Leading C-15 Suffix Char C-15 Ad Hoc network 23 Advanced (wireless connection) 27 AIAG AIAG Strip C-57 AIAG Strip
PAGE 362
Index IATA 2 of 5 C-66 Interleaved 2 of 5 C-22, C-36, C-49, C-64 Matrix 2 of 5 C-37 MSI Plessey C-21, C-35, C-64 UPC A C-17, C-31, C-48, C-60 UPC E C-17, C-32, C-48, C-61 Translation tab 143 bar code reader applications 206 external (specs) 206 external scanner, operation of 179 integrated scanner, operation of 58 internal or integrated 206 Barcodes Must Decode C-43 batteries capacity dialog box 119 charge, time required 180 charge cycles 180 chargers 40 charging 14 gauge 56 installing 39 installing in 753
PAGE 363
Index Code 128 C-15, C-29 Code 128 Emulation C-25, C-41 Code 32, Convert To C-12 Code 32 Prefix C-13 Code 39 C-56–C-57 Code 39 C-12, C-27 Code 93 C-19, C-33, C-49, C-62 Code 93 C-19 cold reset 35 Cold Reset (Shutdown menu) 83 COM, Bluetooth Controls 135 Command Prompt 78 Communities 153 Composite C-24, C-40, C-50 configuring IEEE 802.
PAGE 364
Index contrast (control panel) 101 Display Properties 98 display contrast, adjusting 51 Display Properties 98 docking device icons 57 docking station uploading data using 64 Dot Time C-8, C-44, C-56 double-click appending characters to a decoded bar code 142 scanner trigger 141 Double-Click, Manage Triggers menu 115 Double-Tap (stylus settings) 124 DSSS, 802.11a/g/b radio 204 DSSS, 802.
PAGE 365
Index Include Number Sys C-60, C-61 Include Sym (Code 128) C-58 indicators battery gauge 56 docking devices 57 LED functions 52 modifier keys 55 onscreen 54 scanner message 60, 61 security level 57 task bar 73 tethered device 56 802.
PAGE 366
Index Lithium-ion batteries installing 39 removing 39 Location 152 Lock Sequence 113 Low light Predefined preset D-5 Low light near Predefined preset D-6 Low power Predefined preset D-5 Low Power Timeout C-9, C-27 L1, Set Length C-13 L2, Set Length C-13 M Macro keys accessing 47 executing a macro 108 Macros menu, accessing 107 recording and saving 107 36-key keyboard 47 58-key keyboard 47 maintenance 64 Manage Triggers 114 Matrix Predefined preset D-4 Matrix 2 of 5 C-37 Max Gain (Imager) C-45 Max Illumin
PAGE 367
Index formatting 161 management 160 mounting 162 PDF and linear Predefined preset D-4 PDF internal scanner scanning PDF internal 60 PDF-417 C-24, C-41, C-50 PDM (portable docking module) 190–192 picker cradle 193 installing cable 194 powered 10-55 VDC 193 powered 12 VDC 193 unpowered 193 picker cradle See also Picker Cradle 193 PIN, Bluetooth Controls 129 pinouts A-1 PINs, Bluetooth devices 130 pistol grip, installing 18 Plessy Transmit Check Digit C-35 pocket PC compatibility 89 portable docking module (P
PAGE 368
Index Configure button 21 Connect button 21 EAP (Extensible Authentication Protocol) 24 Infrastructure 23 Key Index 24 Key Index, assigning 24 network authentication 23 Network Key 24 Network Key, assigning 24 wireless information 21 wireless properties 22 802.
PAGE 369
Index Decode Perf.
PAGE 370
Index UPC-E1 Preamble C-18 Verify C-56 warning message 142 Window Height C-43 Window Width C-43 2D Aztec C-52 2D Data Matrix C-51 2D Maxicode C-52 2D QR Code C-51 2D UPC Half Block Stitching C-19 scanning appending characters 142 Check Digit Verification (I 2 of 5) C-49 Code 128 C-29 Code 39 C-12, C-27 Composite C-40 decode zones 210 Enable CC-AB C-40 Enable CC-C C-40 Enable RSS Expanded C-24 Enable RSS Limited C-23 Enable RSS-14 C-23 Linear Transmission only (Decoded Composite) C-40 Linear Transmission on
PAGE 371
Index Enable SNMP 153 Location 152 Name 153 Rights 154 Soft Input Panel (SIP) 91 Soft Scan Timeout 143 SPACE Key 46 specifications battery 221 EV15 1D imager 206 scanner, external 216 scanner, internal 206 SX5400 imager 215 specifications, 75235 G2 201 Standard (Code 128) C-58 Start/Stop Transmit C-28, C-34 Start Menu 75 cycle tasks 80 desktop 76 programs 78 Run 82 Security 76 Settings 81 Shutdown 82 system tray 79 task manager 80 Stop Bits 148, 149, 150 Strip Leading C-15 Strip Start/Stop Chars C-62 Strip
PAGE 372
Index Transmit Code 1D Char C-11, C-57, C-58, C-60, C-61, C-62, C-63, C-64, C-65, C-66 transmit LED 53 Transmit Number System C-31, C-32 trigger, double-click 141 trigger mappings 115 Trigger-Press Type, Manage Triggers menu 117 triggers, configuring 114 Trioptic Code 39, Enable C-12 troubleshooting tips (scanning) 60 turning 7535 G2 off 14 turning 7535 G2 on 14 TweakIT Advanced Services 171 Radio Features 173 TweakIT Settings Advanced Interface and Network 170 U UCC 128(Code 128) C-58 UPC A C-17, C-31,