Hardware Reference Guide For The 7535 March 24, 2004 P/N 8100018 Rev A ISO 9001 Certified Quality Management System
© Copyright 2003 by Psion Teklogix Inc., Mississauga, Ontario This document and the information it contains is the property of Psion Teklogix Inc., is issued in strict confidence, and is not to be reproduced or copied, in whole or in part, except for the sole purpose of promoting the sale of Psion Teklogix manufactured goods and services. Furthermore, this document is not to be used as a basis for design, manufacture, or sub-contract, or in any manner detrimental to the interests of Psion Teklogix Inc.
Return-To-Factory Warranty Psion Teklogix warrants a return-to-factory warranty for a period of one year. In some regions, the warranty exceeds this period. Please contact your local Psion Teklogix office for details. For a list of offices, please refer to Appendix A: “Support Services And Worldwide Offices”.
TABLE OF CONTENTS Chapter 1: Introduction 1.1 1.2 1.3 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Text Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 About The 7535 Hand-Held Computer . . . . . . . . . . . . . . . . . . 4 Chapter 2: The Hardware 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 The Hardware . . . . . . . . . . . . . 2.1.1 Processor . . . . . . . . . . . 2.1.2 Onboard Memory . . . . . . 2.1.3 Hardware Architecture . . . . Identifying Hardware .
Contents 2.9 2.10 2.11 2.12 2.13 2.14 Ports . . . . . . . . . . . . . . . . 2.9.1 The Docking Port . . . . . 2.9.2 The Tether Port . . . . . . 2.9.3 COM Ports On The 7535 . Power Management . . . . . . . . Turning The 7535 On And Off . . Resetting The 7535 . . . . . . . . The Portable Docking Module . . Pinouts And Cables . . . . . . . . 2.14.1 The Serial Port . . . . . . 2.14.2 The Tether Port . . . . . . 2.14.3 The Docking Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents 3.4 3.5 3.6 3.3.2.7 Error Messages. Power Management . . . . . . . . The Filesystem . . . . . . . . . . Locations Of Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 . 40 . 41 . 41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION 1 1.1 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2 Text Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.3 About The 7535 Hand-Held Computer . . . . . . . . . . . . . . . . . .
Chapter 1: Introduction About This Manual 1.1 About This Manual This manual provides development information specific to the Psion Teklogix 7535. General information about developing with the Psion Teklogix SDK For Mobile Devices is given in the Developers’ Guide. Specific information about function calls, methods, etc, is given in the online API Reference Guide.
Chapter 1: Introduction About The 7535 Hand-Held Computer 1.3 About The 7535 Hand-Held Computer The 7535 is a ruggedized hand-held personal computer, running the Microsoft® Windows® CE.NET 4.2 operating system. It is intended for use in commercial and light industrial applications with a focus on real time wireless data transactions. All possible bar code input methodologies are supported by one of the variety of scanners available.
2 THE HARDWARE 2.1 The Hardware . . . . . . . . . . . 2.1.1 Processor . . . . . . . . 2.1.2 Onboard Memory . . . 2.1.3 Hardware Architecture . 2.2 Identifying Hardware . . . . . . . 2.3 The Scanner . . . . . . . . . . . . 2.4 The Display . . . . . . . . . . . . 2.4.1 Touch Input . . . . . . 2.5 The Keyboard . . . . . . . . . . . 2.6 The LEDs . . . . . . . . . . . . . 2.7 The Beeper . . . . . . . . . . . . . 2.8 Accessory Cards . . . . . . . . . . 2.9 Ports . . . . . . . . . . . . . . . . 2.9.
Chapter 2: The Hardware The Hardware 2.1 The Hardware Figure 2.1 The 7535 2.1.1 Processor The 7535 is built around a 400-MHz Intel PXA255 processor. This ARM-corebased CPU is also known as XScale™, and is the successor to the StrongArm SA1110. This processor has many integrated peripherals, such as UARTs, PCMCIA/CF, and LCD controllers. 2.1.2 Onboard Memory The 7535 has 32 megabytes of flash memory and 64 megabytes of RAM. 2.1.
Chapter 2: The Hardware Identifying Hardware There are also two PIC microcontrollers; one scans the matrix keyboard and controls the LEDs, and the other drives the keyboard backlight. 2.2 Identifying Hardware The 7535’s hardware configuration is listed in the information provided by the System Properties applet in the Control Panel. To reach this manually: 1. Press Blue + 0 to open the start menu. 2. Select Settings, Control Panel. The Control Panel opens. 3. Double-click on the System icon.
Chapter 2: The Hardware The Scanner 2.3 The Scanner The 7535 can support the following scanners, internal or external: • 1D scanner • PDF 417 2D scanner • image scanner Only one scanner is installed in the 7535, but a second handheld scanner can be connected via the tether port. Internal scanners can be triggered from the trigger switch on the 7535’s handgrip (if present) or from the Scan button on the 7535’s keyboard. External scanners can only be triggered from their own trigger switch. 2.3.
Chapter 2: The Hardware Imaging Scanners cessor. Activation of the scanner trigger(s) or the keyboard scan button(s) will initiate a scan with the appropriate scanner. The decoded scan driver is responsible for receiving scan data and passing it to the Scan Control Service. 2.3.4 Imaging Scanners The 7535 can support an imaging scanner; both internal and external imaging scanners are supported. Psion Teklogix provides a driver for this scanner. 2.
Chapter 2: The Hardware The Keyboard Backlight 2.5.1 The Keyboard Backlight The 7535 has a backlight behind its keyboard. This backlight can only be turned off and on, not adjusted for brightness, but it can be configured to turn on when the ambient light level drops below a configured value. 2.6 The LEDs The 7535 has four tri-coloured indicator LEDs. Radio LED User Application LED Scan LED Charge LED Figure 2.2 Indicator LEDs 2.6.
Chapter 2: The Hardware Radio Traffic LED 2.6.2 Radio Traffic LED The upper-left LED on the 7535 flashes either orange or green to indicate when the radio transmits and receives data. Note: While the standard 802.11b radio available for the 7535 supports the transmit/receive LED, not all radios support this function. Function Radio Traffic LED Behaviour Radio Transmit Radio Receive LED flashes orange. LED flashes green. Table 2.2 Transmit and Receive LEDs 2.6.
Chapter 2: The Hardware Accessory Cards 2.8 Accessory Cards The 7535 can accept accessory cards, which fit into internal slots in the unit. The 7535 has two slots which accept the following types of accessory cards: • Compact Flash (CF) cards. • MultiMedia Cards (MMCs). • Secure Digital (SD) cards. These cards can contain additional memory, or other accessories. The Compact Flash slot is normally occupied by a radio. Typically, 7535 hand-helds are configured at the factory and arrive ready for use.
Chapter 2: The Hardware The Docking Port Available peripherals include chargers and a Portable Docking Module (PDM) that provides connections for USB host port, USB client port, and a serial port. See “The Portable Docking Module” on page 17 for details about the PDM. Figure 2.3 The Docking Port The docking port supplies DC power, a serial port, a USB host port, and a USB client port. Power Power for charging the batteries and powering the terminal (9-24 V DC; 3.
Chapter 2: The Hardware The Tether Port USB Client Port The docking port provides a USB client interface to connect the 7535 to a USB host computer or hub. The 7535 acts as a USB serial device via the USB client port. On the 7535, this serial device is COM4. The 7535 also can act as a USB client (a Mass Storage Device), when its bootloader is running, to allow software updates via USB. Dock ID By reading a resistance value, the 7535 can identify the device attached to the docking port.
Chapter 2: The Hardware COM Ports On The 7535 See “Section 2.14.2 The Tether Port” on page 19 for details of the devices that can connect to the tether port. 2.9.3 COM Ports On The 7535 The 7535 has the following COM ports: COM Port Use COM1 Tether port COM2 Reserved (internal use only) COM3 Console port COM4 USB port 2.10 Power Management The 7535 is powered by a lithium-ion rechargeable battery pack. The 7535 can be powered from external power when used with the AC adaptor.
Chapter 2: The Hardware The Portable Docking Module • Press and hold down the Blue key and the Enter/On key simultaneously for a minimum of six seconds. The four indicator LEDs light for a second, and the screen displays the Psion Teklogix and Microsoft® Windows® CE.net splash screen before displaying the startup desktop. To reset the 7535 and display the boot loader: • Press and hold down the Scan key, the Blue key and the Enter/On key simultaneously for a minimum of six seconds.
Chapter 2: The Hardware The Portable Docking Module • Serial port. This 9-pin D-connector accepts a null-modem serial cable to connect to the development machine. • USB type B port. This port accepts a cable from a USB host (typically the development computer). It can be used for OS image updates, ActiveSync connections and application debugging. • USB type A port. This port connects the 7535 to other devices; the 7535 serves as a USB host. This port can be used to connect a USB mouse and keyboard.
Chapter 2: The Hardware Pinouts And Cables 2.14 Pinouts And Cables 2.14.1 The Serial Port The RS232 serial port on the 7535’s Portable Docking Module has the standard 9pin pinout; however, the PDM only passes the TxD, RxD, and Ground signals to the 7535’s docking connector. There is no hardware flow control. The serial cable supplied is a 9-pin-to-9-pin null-modem cable, Psion Teklogix part number 9003659.
Chapter 2: The Hardware The Tether Port • Psion Teklogix ScanSee, a scanner and input device which can be worn on the back of the hand. The tether port on the 7535 accepts an eight-pin custom connector: Figure 2.5 Tether Port Connector A mating connector is available from Psion Teklogix with part number 1020060. The 7535 distinguishes between devices connected to the tether port by reading the resistance between pin 8 and pin 5 of the tether port.
Chapter 2: The Hardware The Tether Port Table 2.5 Recognized Tether Port Resistance Values Devices that connect to the tether port may be wired as follows: USB Device Tether Connector Pin Pin Description 1 2 VCC (+5 V from 7535) 3 USB+ 4 USB- 5 GND 6 7 8 150k Ohm Resistor (Connect the other end of resistor to pin 5) Table 2.
Chapter 2: The Hardware The Tether Port Symbol P300STD Non-decoded Scanner Tether Connector Pin Description 1 SCN_TRIG (TRIGGER) 2 VCC (+5V from 7535) 3 SOS (SOS) 4 SCN_DATA (DEP) 5 GND (GND) 6 SCAN_ENABLE (ENABLE) 7 SCN_ACK (DECODE) 8 8.66k Ohm Resistor (Connect the other end of resistor to pin 5) Table 2.
Chapter 2: The Hardware The Tether Port Symbol P304PRO Decoded Scanner Tether Connector Pin Description 1 RXD (to 7535) 2 VCC (+5 V from 7535) 3 4 TXD (from 7535) 5 GND 6 7 8 4.53k Ohm Resistor (connect the other end of resistor to pin 5) Table 2.10 Tether Connector Pinout For Symbol P304PRO Decoded Scanner Generic Serial Device Tether Connector Pin 1 Pin Description RXD (to 7535) 2 3 CTS (to 7535) 4 TXD (from 7535) 5 GND 6 7 RTS (from 7535) 8 16.
Chapter 2: The Hardware The Docking Port ScanSee Tether Connector Pin Pin Description Pin On ScanSee 1 RXD (to 7535) W4 2 VCC (+5V from 7535) W2 4 TXD (from 7535) W3 5 GND W1 3 6 7 8 1.82k Ohm Resistor (Connect the other end of resistor to pin 5) Table 2.12 Tether Connector Pinout For ScanSee 2.14.
Chapter 2: The Hardware The Docking Port Pin Number Purpose Notes 1 EXT_5V Switched 5V DC from 7535 (2 A max) 2 RXD RS232 RxD (7535 console port) 3 TXD RS232 TxD (7535 console port) 4 PWR_IN DC input to 7535 (9-20 V DC; 3.4 A max) 5 USB Host - USB host data - (to USB peripherals) 6 USB Host + USB host data + (to USB peripherals) 7 PWR_IN DC input to 7535 (9-20 V DC; 3.
3 THE SOFTWARE 3.1 Overview Of The 7535’s Software . . 3.2 The Boot Process. . . . . . . . . . . . 3.2.1 Overview . . . . . . . . . . 3.2.2 Boot Types . . . . . . . . . 3.2.2.1 Cold Boot . . . . . . 3.2.2.2 Warm Boot. . . . . . 3.2.3 Other Power Transitions . . 3.2.3.1 Suspend . . . . . . . 3.2.3.2 Resume . . . . . . . 3.2.4 User Interface . . . . . . . 3.3 The Shell . . . . . . . . . . . . . . . . 3.3.1 Overview . . . . . . . . . . 3.3.2 System Structure . . . . . . 3.3.2.1 The System Monitor . 3.3.2.
Chapter 3: The Software Overview Of The 7535’s Software 3.1 Overview Of The 7535’s Software This chapter describes features of the boot process and operating-system software that are specific to the 7535. The 7535 uses a custom build of Microsoft’s Windows CE.NET 4.2, with OS-native device drivers for its custom hardware. It can accept executables written for the Intel X-Scale PXA255 processor, or (with the appropriate runtime engine) .NET CIL executables or Java bytecode executables.
Chapter 3: The Software Boot Types • the first time the terminal is turned on at the factory (‘initial software load’) • the terminal is turned on after it is powered down (‘cold boot’) • the terminal is turned on after it was suspended (‘resume from suspend’). The most common type of boot is the resume from suspend. When the 7535 is turned off, it enters a ‘suspended’ state, where its main processor is stopped, but retains the contents of its RAM.
Chapter 3: The Software Other Power Transitions The bootloader performs minimal initialization and waits until it gets a ‘Go’ message back from the peripheral controller, after which it: 10. Fully initializes itself. 11. Writes a message on the terminal screen and the console port. 12. Loads the OS image into RAM. 13. Runs the OS image. While the Windows CE image is being loaded into RAM, a splash screen is displayed on the terminal’s display.
Chapter 3: The Software User Interface • by pressing the OFF key-combination Blue + Enter. If the unit is running on battery power, and the remaining battery power drops to critical levels as reported by the battery pack, the system will transition gracefully to the Suspend state, and no data will be lost. If the unit is running on external power without a battery installed, and external power is removed, the system will make a ‘non-graceful’ transition to the Suspend state.
Chapter 3: The Software User Interface • When the main operating system is loaded and run, a splash screen is displayed on the terminal’s screen. • At the end of the boot process, the 7535’s shell is displayed on the screen. Status messages are written to the 7535’s serial console ports during the boot process. The peripheral controller and the main processor console ports are multiplexed on the same physical port.
Chapter 3: The Software The Shell • Suspend Threshold This is the percentage of battery charge left when the unit executes the Runto-Suspend transition. This setting is on the Suspend Threshold tab of the Power Properties dialog. Possible settings are: 0 to 50 percent, in 5% steps. 3.3 The Shell 3.3.1 Overview The shell is responsible for providing an interface to the user for access to the terminal’s applications, files, and configuration.
Chapter 3: The Software System Structure Memory Monitoring When the free memory drops below a configurable limit, the shell sends a ‘hibernate’ message to the last used application window. Application windows are supposed to reduce their memory consumption when they receive this message. If the free memory situation has not improved, the system monitor will send hibernate messages to the other windows. Power Monitoring The power monitor provides two different means of feedback to the user.
Chapter 3: The Software System Structure 3.3.2.2 The Desktop Desktop System Tray Task Bar The desktop provides the user with a starting point to access the terminal’s file system (through a link to Windows Explorer), and configuration (through a link to the Control Panel). The user may also put any applications or files in the \Windows\desktop folder and they will be displayed on the desktop. This gives the user quick and easy access to files and applications they might use frequently.
Chapter 3: The Software System Structure The taskbar registers itself with the OS. The OS sends the taskbar two kinds of special messages: • application creation and destruction events. • certain key presses and key sequences. Application creation and destruction events can be used for displaying buttons on the taskbar for running applications. Key presses and key sequences can be used by the shell for any purpose.
Chapter 3: The Software System Structure The Task Manager The task manager is a dialog box that is created on startup but is only displayed when the user requests it (by pressing Blue + 0, then T, or by pressing Alt + Esc, or by selecting Start Menu, Task Manager). When it is displayed, it lists the currently running applications. It allows the user to start a new application, close a running application, or bring a running application to the foreground.
Chapter 3: The Software System Structure 3.3.2.4 Navigation The shell and the standard start menu are fully navigable using the keyboard. The following table outlines special keys and key combinations for the shell.
Chapter 3: The Software Power Management 3.3.2.6 Differences The customized Psion Teklogix shell is an enhanced version of the Handheld PC (HPC) shell, which is similar to the shell on the desktop version of Windows. There are some modifications to account for differences between the typical HPC and the 7535’s screen size and requirements.
Chapter 3: The Software The Filesystem • If the minimum power consumption limit is set higher than the maximum, the power of the device will remain elevated for as long as the application requires the device. • If the OS transitions to a suspended power state, application-imposed minimum power limits will be set aside while the OS is suspended. 3.5 The Filesystem The filesystem of the 7535 appears as one unified space.
Chapter 3: The Software Locations Of Applications An application can be installed either to RAM or to flash memory. If the application is installed to RAM, it is completely lost when the unit is cold-booted. The default directory for files installed through ActiveSync’s Application Manager is \Program Files\, where is the name of the program. On the 7535, this directory resides in RAM and will be lost during a cold or warm boot.
CONNECTING 4 4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 4.2 USB Serial Connections . . . . . . . . . . . . . . . . . . . . . . . . . . 46 4.3 Bluetooth Wireless Connections . . . . . . . . . . . . . . . . . . . . . .
Chapter 4: Connecting Overview 4.1 Overview This chapter provides connection information specific to the 7535, for connecting to the device through the following methods: • USB serial link. See section 4.2 on page 46. • Bluetooth short-range wireless link. See section 4.3 on page 48. The ActiveSync software from Microsoft can be used to establish communication with the device, once the physical connection has been made.
Chapter 4: Connecting USB Serial Connections Double-click the PC Connection icon in the Control Panel. The PC Connection Properties dialog appears. Verify that the checkbox that allows connection to the desktop is checked: “Connect Using” specifies the port to be used for connecting to the PC: • USB specifies using the USB Type-B (client) port of the 7535. This port is provided on the Portable Docking Module. • Bluetooth specifies using the internal Bluetooth connection of the 7535 (if present).
Chapter 4: Connecting USB Serial Connections Any device that draws less than 100 mA from the USB cable is called a “low-powered” device; this includes self-powered devices that need no power, as well as devices such as tablets and mice that need little power. Devices that draw more than 100 mA from the USB cable are called “high-powered” devices. The USB cable must be connected to another device that can supply this power.
Chapter 4: Connecting Bluetooth Wireless Connections 9. Press OK. The Settings dialog disappears. 10. Select File, Get Connected. The Get Connected wizard appears. 11. Press Next. ActiveSync searches for a connection. On the 7535... 12. Select Start, Programs, ActiveSync, direct. A dialog appears, indicating that the 7535 is attempting to connect. 13. A successful connection is indicated by a blue icon in the 7535’s system tray.
Chapter 4: Connecting Bluetooth Wireless Connections • An existing ActiveSync partnership between the 7535 and the PC. This partnership must be established through the USB connection. To connect: 1. Select Blue + 0. The Start Menu opens. 2. Select Settings. The Control Panel opens. 3. Double-click on the Bluetooth Device Properties icon. The Bluetooth Manager dialog opens. 4. Ensure that the development PC is powered on and that its Bluetooth radio is enabled. 5.
Chapter 4: Connecting Bluetooth Wireless Connections 9. Select Trusted to make this service trusted. A dialog appears asking whether authentication is needed. 10. If authentication is needed for the service, click Yes, then enter the PIN. When the 7535 tries to connect with a remote device that has Authentication enabled, you will be prompted to verify the PIN. The Authentication Request dialog will appear. Enter the PIN, press OK, and the devices will be connected. 11. Press OK.
Chapter 4: Connecting Bluetooth Wireless Connections 23. Press Next. ActiveSync searches for a connection. On the 7535... 24. Click on the Start button, then Programs, then ActiveSync, and select remote from the ActiveSync submenu. A dialog appears, indicating that the 7535 is attempting to connect. 25. A successful connection is indicated by a blue icon in the 7535’s system tray. The 7535 and the PC will also play sounds to indicate that they are connected, if sound is enabled on the devices.
REINSTALLING THE OS 5 5.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 5.1.1 Displaying The Datecode Of The Operating System . . . . 55 5.2 Serial Download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 5.2.1 Equipment Needed . . . . . . . . . . . . . . . . . . . . . . 56 5.2.2 Upgrading The Software Image . . . . . . . . . . . . . . . 56 5.3 USB Download . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 5.3.1 Equipment Needed . . . . . . . .
Chapter 5: Reinstalling The OS Overview Displaying The Datecode Of The Operating System 5.1 Overview This section describes what you need to do to replace the operating system on your 7535. The OS software image on a 7535 contains the Windows CE .NET operating system (OS), the .NET runtime engine, and all the software included with the 7535. It may also include Open TekTerm (Psion Teklogix’ terminal emulator program), or the Jeode Java Virtual Machine (JVM).
Chapter 5: Reinstalling The OS Serial Download Equipment Needed • Enter the Control Panel, select the System icon, and open the Properties tab. The item for “WinCE Code” displays the datecode of the OS image. • Hold down the 7535’s Scan, Blue and Enter buttons for 6 seconds. The 7535 boots into its boot loader and displays the datecode of the OS image. 5.2 Serial Download This section explains how to replace the operating-system software image on a 7535 through a serial cable. 5.2.
Chapter 5: Reinstalling The OS Serial Download Upgrading The Software Image Psion Teklogix 7535 BooSt. Copyright Psion Teklogix Inc. 2002, 2003 Starting BooSt... Graphical console connected.
Chapter 5: Reinstalling The OS Serial Download Upgrading The Software Image 4. Set the serial communications software for the port where the serial cable is connected. Use 8 data bits, no parity, one stop bit (8N1), a data rate of 115 200 bits per second, and no flow control. 5. Start the serial communications software. 6. Press Enter. The 7535 echoes a menu to the PC’s screen through the communications software. This menu is also displayed on the 7535’s own screen.
Chapter 5: Reinstalling The OS USB Download Equipment Needed Note: You may need to reconfigure any changes done to the system configuration through the Control Panel. The registry will be set to default values if the new OS determines that the previously-existing registry values are not compatible. 5.3 USB Download This section explains how to replace the operating-system software image in a 7535 through a USB cable. 5.3.
Chapter 5: Reinstalling The OS USB Download Upgrading The Software Image 1. Hold down the Scan, Blue and Enter buttons simultaneously for 6 seconds. The 7535 reboots to the BooSt bootloader and displays text similar to the following: Psion Teklogix 753x BooSt. Copyright Psion Teklogix Inc. 2002, 2003 Starting BooSt... Graphical console connected.
Chapter 5: Reinstalling The OS USB Download Upgrading The Software Image The A end of the USB cable plugs into your PC and the smaller square B end of the cable plugs into the portable docking module connected to the 7535. When the USB connection is established, a new drive appears on your PC named “Removable Disk”.
Chapter 5: Reinstalling The OS USB Download Upgrading The Software Image Once the Removable Disk has been properly stopped on the PC, the BooSt Console displays a message similar to the following: nand0-0 mounted: size = 16220160 (31680 * 512) > The flash memory containing the operating-system image has been disconnected from the development computer and is now accessible by the bootloader. The regular bootloader commands (1 and !) to load and run the main operating system now work. 6.
APPENDIX A SUPPORT SERVICES AND WORLDWIDE OFFICES Psion Teklogix provides a complete range of product support services to its customers worldwide. These services include technical support and product repairs. A.1 Technical Support Technical Support for Mobile Computing Products is provided via e-mail through the Partner Program website. To reach the website, go to www.psionteklogix.com and click on the Partner Program link, which takes you to the Partner Program page.
A.3 WORLDWIDE OFFICES COMPANY HEADQUARTERS AND CANADIAN SERVICE CENTRE NORTH AMERICAN HEADQUARTERS AND U.S. SERVICE CENTRE Psion Teklogix Inc. 2100 Meadowvale Boulevard Mississauga Ontario Canada L5N 7J9 Tel: +1 905 813 9900 Fax: +1 905 812 6300 E-mail: salescdn@psion.com Psion Teklogix Corp. 1810 Airport Exchange Boulevard Suite 500 Erlanger, Kentucky USA 41018 Tel: +1 859 371 6006 Fax: +1 859 371 6422 E-mail: salesusa@psion.
Psion Teklogix Africa Postnet Suite 39, Private Bag x11 Halfwayhouse, 1685 Ground Floor East Waterfall Edge Phase 2, Waterfall Park Bekker Road MIDRAND 1685 South Africa Tel: +27 11 805 7440/1/2 Fax: +27 11 805 7444 Psion Teklogix Systems India Pvt. Ltd. M-74, 1st Floor, “M” Block Market Greater Kailash-Il New Delhi - 110048 India Tel: +91 11 26219257 Fax: +91 11 26219076 E-mail: tekind@psion.com Psion Teklogix Wireless Technologies (Shanghai) Ltd. Unit 1507-08 Mingshen Building No.
INDEX Boldface indicates a parameter, menu or sub-menu name. A ActiveSync 45 default installation folder 42 disconnecting 45 guest 45 partnership 45 applications install to flash or RAM 42 B Bluetooth connections 48 Bluetooth Manager 49 Bluetooth radio changing device name 49 device service profiles 49 radio configuration 49–51 C .
Index L LAN access using PPP service, Bluetooth 49 LED charge 11 receive 12 scan 12 transmit 12 "low-powered" USB defined 47 "low speed" USB defined 46 M memory and application install location 42 card folder names 41 internal flash 42 memory monitor 35 messages error 40 monitor of memory 35 of power 35 of security 35 of system 34 N names of memory card folders 41 null-modem cable part number 18 O operating system displaying datecode 55 distinguishing variants 55 image part numbers 55 registry keys
Index S security levels on terminal 35 serial cable 19 part number 18 serial connections USB 46 Serial service, Bluetooth 49 shell colour schemes 39 defined 34 desktop icons 38 differences between Psion Teklogix and standard 40 key combinations 39 location of taskbar 38 startup .
