EP10 Hand-Held Computer (Model Number 7515) Windows Embedded 6.5 User Manual April 5, 2011 ISO 9001 Certified Quality Management System Part No. 8000227.
This user manual supports Model Numbers: • 7515U with FCC ID: GM37515UA and IC: 2739D-7515UA • 7515C with FCC ID: GM37515CA © Copyright 2011 by Psion Inc., Mississauga, Ontario 2100 Meadowvale Boulevard, Mississauga, Ontario, Canada L5N 7J9 http:\\www.psionteklogix.com This document and the information it contains is the property of Psion Inc.
Preliminary Draft TABLE OF CONTENTS Chapter 1: Introduction 1.1 1.2 1.3 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Text Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 EP10 Hand-Held Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preliminary Draft Contents 2.9.1 Pairing a Bluetooth Headset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 2.10 Inserting the microSD and SIM Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 2.10.1 Inserting the Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.11 The Camera . . . . . . . . . . . . . . .
Preliminary Draft Contents 4.2 4.3 Games . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 ActiveSync® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 4.3.1 Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preliminary Draft Contents 4.17 Internet Explorer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 4.17.1 Browsing Web Sites. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 4.18 Messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preliminary Draft Contents 5.15 Backlight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 5.15.1 Battery Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120 5.15.2 External Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .121 5.
Contents Preliminary Draft 5.33.3 Translations Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .154 5.33.4 Ports Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .157 5.34 Total Recall. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preliminary Draft Contents 5.43 Wireless Statistics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .197 5.44 Wireless WAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .197 5.44.1 Softkey Bar Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preliminary Draft Contents 6.7.5 6.7.6 6.8 6.9 6.10 6.11 Charging Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .235 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .235 Snap Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preliminary Draft 7.2.3 7.2.4 7.3 7.4 Contents Sierra Wireless MC5728V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .261 Cinterion PH8 GSM/GPRS/EDGE Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .263 Lithium-Ion 3600 mAh Battery Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .265 Internal Imager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preliminary Draft C.3 C.4 x C.2.17 RSS Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-17 C.2.18 Composite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-18 C.2.19 PDF-417. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-18 C.2.
Preliminary Draft C.4.11 C.4.12 C.4.13 C.4.14 C.4.15 C.4.16 C.4.17 C.4.18 C.4.19 C.4.20 C.4.21 C.4.22 C.4.23 C.4.24 C.4.25 C.4.26 Contents RSS Code (Reduced Space Symbology) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-41 Composite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-41 PDF-417. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preliminary Draft Contents D.5 xii D.4.7 Configuring The Bar Code Decoding Symbologies . . . . . . . . . . . . . . . . . . . . . . . . . . D-13 D.4.8 Setting The Active Preset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-14 D.4.9 Viewing A Preset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-14 D.4.10 Creating A Custom Preset . . . . . . . . . . . . . . . . . . . . . . .
Preliminary Draft INTRODUCTION 1 1.1 About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2 Text Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.3 EP10 Hand-Held Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.3.1 The EP10 Hand-Held. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft
Preliminary Draft 1.1 Chapter 1: Introduction About This Manual About This Manual This manual describes how to configure, operate and maintain the EP10 Hand-Held Computer (Model Number 7515). Chapter 1: Introduction provides a basic overview of the EP10 Hand-Held. Chapter 2: Basic Checkout describes the steps required to get the EP10 ready for operation Chapter 2: Getting to Know the EP10 describes the features and outlines how to charge and maintain the battery.
Chapter 1: Introduction Text Conventions 1.2 Preliminary Draft Text Conventions Note: Notes highlight additional helpful information. Important: These statements provide particularly important instructions or additional information that is critical to the operation of the equipment. Warning: These statements provide critical information that may prevent physical injury, equipment damage or data loss. 1.
Preliminary Draft Chapter 1: Introduction EP10 Hand-Held Features User Interface • Display (Backlit) - 3.7 in. VGA portrait mode - Backlight feature 165 cd/m2 output - Sunlight readable with integrated touchscreen - Colour 480 x 640 graphic TFT - Passive stylus or finger operation • Audio - Built-in 85db mono speaker - microphone - receiver • Keyboard (Backlit) - QWERTY - High reliability keypad ultra-white backlight - Ergonomically enhanced for ambidextrous one-hand operation • Camera - 3.
Chapter 1: Introduction The EP10 Hand-Held Preliminary Draft Enhanced Features • • • • • Accelerometer Digital Compass Gyroscope Light Sensor Proximity Sensor Expansion Slot • One microSD slot VOIP (Voice Over IP) • 1.3.1 Push-to-talk The EP10 Hand-Held Figure 1.1 EP10 Hand-Held – QWERTY 6 EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft Chapter 1: Introduction The EP10 Hand-Held Figure 1.2 Phone Keys Send Key End Key Note: Refer to “Sending & Ending Phone Calls using the Phone Keypad” on page 33 for details about these keys. EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft
Preliminary Draft 2 GETTING TO KNOW THE EP10 2.1 Features of the EP10 Hand-Held . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2.2 The Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2.1 Battery Safety . . . . . . . . . . . . . . . . . . . . . . . . . 2.2.2 Removing the Battery Pack . . . . . . . . . . . . . . . . . . 2.2.3 Battery Swap Time . . . . . . . . . . . . . . . . . . . . . . . 2.2.4 Charging the Battery . . . . . . . . . . . . . . . . . . . . . . 2.2.4.
Preliminary Draft 2.10.1 Inserting the Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.11 The Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.12 General Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.12.1 Caring for the Touchscreen . . . . . . . . . . . . . . . . . . . . . . . . . 26 2.12.2 Cleaning the EP10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preliminary Draft 2.
Chapter 2: Getting to Know the EP10 The Battery Preliminary Draft Figure 2.1 Back of EP10 Stylus Speaker Flash Camera Battery Latch Battery & SIM/microSD Card Compartments Hand Strap Anchor Figure 2.2 Ports Docking Port/ USB On-The-Go Hand Strap Anchor 2.2 The Battery The EP10 operates with a 3600 mAh, Lithium-Ion battery pack, Model No. RV3010. Preparing the EP10 for operation requires that a battery pack be charged and installed in the EP10. 12 EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft 2.2.1 Chapter 2: Getting to Know the EP10 Battery Safety Battery Safety Important: Before attempting to install, use or charge the battery pack, it is critical that you review and follow the important safety guidelines in the quick reference guide entitled ‘EP10 Hand-Held Regulatory & Warranty Guide’, PN 8000235. 2.2.2 Removing the Battery Pack Important: Always shut down the EP10 before removing the battery.
Chapter 2: Getting to Know the EP10 Charging the Battery Preliminary Draft Note: Do not leave a spare battery to charge for more than 72 hours. Charging for more than 72 hours may damage the battery or lead to charge capacity reduction. Important: If the battery is overheated (>60° C) or if the battery capacity is very low (<100 mAh), the unit will not switch on when the Power key is pressed.
Preliminary Draft Chapter 2: Getting to Know the EP10 The Keyboard Note: Refer to “Monitoring the Battery and Maximizing Run Time” on page 23 for additional information about the battery. Important: To avoid damaging the battery, chargers will not begin the charge process until the battery temperature is between 0°C to 40°C (32°F to 104°F). 2.3 The Keyboard 2.3.1 EP10 QWERTY Keyboard The EP10 is available with a QWERTY keyboard with [Send] and [End] phone keys. Figure 2.
Chapter 2: Getting to Know the EP10 Locking the Keyboard Preliminary Draft Note: Almost all keys can be reprogrammed to suit your requirements. 2.3.2 Locking the Keyboard You can lock the keyboard to prevent accidental key presses. To set up the locking/unlocking key sequence: Tap on Start>Settings>Buttons. Tap on the right arrow icon in the bottom-right corner of the screen to scroll to the Lock Sequence tab. Refer to “Lock Sequence” on page 106 for details about setting up this function. • 2.3.
Preliminary Draft Chapter 2: Getting to Know the EP10 The Keys Figure 2.4 Shift-State Indicator Icon Shift-State Indicator Icon replaces Soft Keyboard Icon Soft Keyboard Icon 2.3.3.2 Locking Modifier Keys Note: The locking behaviour of the modifier keys can be changed so that, for example, pressing a modifier key once will lock the key ‘on’. Refer to “One Shots” on page 99 for details. Note too that by default, the [ORANGE] key is locked ‘on’ when pressed only once.
Chapter 2: Getting to Know the EP10 The Keys Preliminary Draft key, an upper case character is displayed. When you press a numeric key, the associated symbol on the numeric key is displayed on the screen. If you press the [SHIFT] key twice, it is locked ‘on’ essentially acting as a [CAPS] key, displaying uppercase characters. In this state, if you type a numeric key, the number rather than the symbol above it is displayed. Press [SHIFT] again to turn the [CAPS] function off.
Preliminary Draft Chapter 2: Getting to Know the EP10 The Keypad Backlight The Function Keys–[F1] to [F10] Function keys [F1] to [F10] perform special, custom-defined functions. These keys are accessed by pressing [BLUE] followed by numeric keys [1] to [10]. They can be used with the Windows Mobile 6.5 operating system or another application. The Macro Keys While macro keys are not physically stamped on the keyboard, up to 12 macro functions can be added using the Scancode Remapping function.
Chapter 2: Getting to Know the EP10 Aligning (Calibrating) the Touchscreen Preliminary Draft Important: Keep in mind that this sequence cycles the display backlight up to full brightness and once reached, begins to dim the backlight until the display fades to black – nothing is visible. At this point, you’ll need to continue pressing these keys until the display brightens up to a usable level. 2.4.
Preliminary Draft • Chapter 2: Getting to Know the EP10 Screen Orientation Tap on the Align Screen button, and follow the directions on the screen to align (calibrate) the screen. Note: This window provides two additional tabs: ClearType and Text Size. Tapping on the ClearType tab allows you to enable the ClearType option to smooth screen font appearance. The Text Size tab allows you to increase or decrease the size of the font displayed on the screen. 2.4.
Chapter 2: Getting to Know the EP10 Audio Indicators Preliminary Draft Table 2.1 Function of EP10 LEDs LED Function Yellow Application LED (centre LED) Application LED. This LEDs behaviour is application dependent. Blue Radio Power LED (right-most LED) Radio power indicator. If the EP10 is attached to an external power supply, the charge LED (the left-most LED) reflects the battery charge status. Table 2.
Preliminary Draft Chapter 2: Getting to Know the EP10 Monitoring the Battery and Maximizing Run Time 2.7 Monitoring the Battery and Maximizing Run Time Note: When the battery is at 50% capacity, a ‘low battery’ warning is displayed. When the battery is at about 10% capacity, a ‘very low battery’ notification bubble appears.
Chapter 2: Getting to Know the EP10 Uploading Data in a Docking Station • 2.8 Preliminary Draft A ‘never used’ Lithium-Ion battery that has been stored for 3 years may have limited or no useful life remaining once put into service. Think of batteries as perishable goods. Uploading Data in a Docking Station Important: Review the documentation provided with the user application installed in your EP10 before performing data uploads.
Preliminary Draft 2.9.1 Chapter 2: Getting to Know the EP10 Pairing a Bluetooth Headset Pairing a Bluetooth Headset Note: Headset pairing information is also available in the Getting Started Centre in the Today screen on your EP10. Before pairing a headset or any other Bluetooth device with your EP10, make certain that the Bluetooth device power is enabled; it is enabled by default.
Chapter 2: Getting to Know the EP10 Inserting the Cards Preliminary Draft 2.10.1 Inserting the Cards • • • • • • • 2.11 Switch off the EP10 – press and hold down the Power key, and when the Shutdown screen is displayed, choose Shutdown and tap on OK. Slide the battery latch to the right to unlock the battery, and remove it. Pull the SD door down as the arrow icon on the door indicates.(TBD) Orient the microSD or SIM card according to the legend stamped into the plastic.
Preliminary Draft Chapter 2: Getting to Know the EP10 Cleaning the EP10 2.12.2 Cleaning the EP10 Important: Do not immerse the EP10 in water. Dampen a soft cloth with mild detergent to wipe the unit clean. • • • Use only mild detergent or soapy water to clean the EP10 unit. Avoid abrasive cleaners, solvents or strong chemicals for cleaning. The plastic case is susceptible to harsh chemicals. The plastic is partially soluble in oils, mineral spirits and gasoline.
Preliminary Draft
Preliminary Draft 3 USING WINDOWS EMBEDDED 6.5 3.1 Navigating in Windows Embedded 6.5 and Applications 3.1.1 Navigating using a Touchscreen and Stylus . . 3.2 Windows Embedded 6.5 Desktop – Today Screen. . . . 3.2.1 Windows Embedded 6.5 Navigation Bar . . . 3.2.2 Today’s Date, Clock and Alarm . . . . . . . . 3.2.3 Ownership Information. . . . . . . . . . . . . 3.2.4 E-mail Notification . . . . . . . . . . . . . . . 3.2.5 Task Notification . . . . . . . . . . . . . . . . 3.2.
Preliminary Draft 3.10.3 Block Recognizer and Letter Recognizer . . . . . . . . . . . . . . . . . . 54 30 EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft Chapter 3: Using Windows Embedded 6.5 Navigating in Windows Embedded 6.5 and Applications 3.1 Navigating in Windows Embedded 6.5 and Applications Graphic user interfaces like Windows Embedded 6.5 for portable devices or desktop Windows (2000, XP, etc.) utilize ‘point and click’ navigation. On the EP10, this is accomplished using a touchscreen and stylus rather than a mouse. 3.1.
Chapter 3: Using Windows Embedded 6.5 Windows Embedded 6.5 Navigation Bar Preliminary Draft The Today screen displays all your important information – tasks, unread e-mails and upcoming appointments – all in one place. The Start menu provides access to everything else you’ll need. 3.2.1 Windows Embedded 6.5 Navigation Bar The navigation bar along the top of the screen provides icons that, when tapped, open their associated programs. If you’re unit is equipped with Windows Embedded 6.
Preliminary Draft Chapter 3: Using Windows Embedded 6.5 Windows Embedded 6.5 Navigation Bar Connectivity The Connectivity hotkey provides a shortcut to the Connections tab in the Settings window. This tab provides access to Bluetooth, network, network card and internet connection setups. Phone Settings If your EP10 is running Windows Embedded 6.5, it is equipped with a phone option.
Chapter 3: Using Windows Embedded 6.5 Today’s Date, Clock and Alarm Preliminary Draft Two volume adjustments are provided – one for the speaker volume and the other for the phone dialer volume. Speaker Volume Phone Dialer Volume Battery Capacity Tapping on the Battery hotkey displays the Battery tab allowing you to view the remaining battery capacity in the battery. 3.2.2 Today’s Date, Clock and Alarm This option displays the current date.
Preliminary Draft Chapter 3: Using Windows Embedded 6.5 Today’s Date, Clock and Alarm The Clock & Alarms screen is displayed. • Tap on the drop-down menu arrows to set the GMT, time and date. An option to set the date and time for a visiting time zone is also available. To set an alarm: • Tap on the Alarms tab. You can set a maximum of three alarms. • • Tap in the checkbox to enable an alarm. Tap the day on which you want the alarm to go off – Sunday through Saturday.
Chapter 3: Using Windows Embedded 6.5 Ownership Information • Preliminary Draft Tap on the time to display the clock. Time Field • To set the time, in the time field below the clock, tap on the hour to highlight it, and type the hour at which you want the alarm to ring. To set the minutes, highlight the minutes, and type the appropriate minutes, or You can also assign the alarm activation time using the clock graphic. Position the stylus on the hour hand of the clock, and drag it to the correct hour.
Preliminary Draft Chapter 3: Using Windows Embedded 6.5 E-mail Notification • Tap on Owner, listed in the Today screen as Tap here to set owner information to display a screen in which you can type information. • Type your name, company name, address, telephone number and e-mail address. Note: You can type information using the EP10 keyboard, or you can tap on the soft keyboard icon in the bottom right corner of the softkey bar to display an onscreen keyboard.
Chapter 3: Using Windows Embedded 6.5 Task Notification • Preliminary Draft Tap on the Tasks option to display a list of tasks. Creating a Task • • • Tap in the field labelled Tap here to add a new task. The text is replaced with a blinking cursor. If you prefer to type the task using the soft keyboard, tap on the soft keyboard icon in the softkey bar. Type your task description. Tap anywhere in the blank part of the screen, or press the Power button to add the task to your list.
Preliminary Draft Chapter 3: Using Windows Embedded 6.5 Task Notification Figure 3.1 Task Details Screen Each of the nine items in this screen, when tapped, displays a drop-down menu where you can choose from a list of options. • Once you’ve completed all the appropriate fields, tap on OK to save your changes. Note: You can also tap on the Notes tab to add additional information about the task your are defining. The task will be listed in the Today screen as an Active Task.
Chapter 3: Using Windows Embedded 6.5 Calendar of Upcoming Appointments Preliminary Draft You can choose All Tasks, Recently Viewed, No Categories, Active Tasks, or Completed Tasks. The tasks are displayed on the screen according to the preference you chose. 3.2.6 Calendar of Upcoming Appointments This option is used to map out all your upcoming appointments, meetings and so on in the weeks, months and years ahead.
Preliminary Draft Chapter 3: Using Windows Embedded 6.5 Calendar of Upcoming Appointments Figure 3.2 Appointment Detail Screen • • In the Subject field, name the appointment. Complete the remaining fields to reflect your appointment details. Note: Refer to “Adding Reminders” on page 41 for details about reminders. Refer to“Using Categories” on page 42 for information about this option. • Tap on OK to save your changes and close the screen. 3.2.6.
Chapter 3: Using Windows Embedded 6.5 Calendar of Upcoming Appointments • Preliminary Draft Tap the appointment in the Calendar screen to display it in a summary screen. The reminder is indicated by the small, bell icon. 3.2.6.3 Using Categories Categories help you organize and track the different types of data you keep on your EP10. To assign an appointment to a category: • Tap on an appointment in the Today screen. In the Calendar screen, tap on the appointment again.
Preliminary Draft Chapter 3: Using Windows Embedded 6.5 Start Menu Note: You can create a new category by tapping on New in the softkey bar at the bottom of the screen. 3.2.6.4 Deleting Appointments • • 3.3 Tap and hold the stylus on the appointment you want to delete. Tap on Delete Appointment in the pop-up menu. Start Menu To display the Start menu: • Tap on the Start button in the upper-left corner of the Navigation Bar.
Chapter 3: Using Windows Embedded 6.5 Managing Files and Folders 3.4 Preliminary Draft • Tap on Start>Settings. • In the Personal tab, tap on the Menus icon. • Tap the checkboxes next to the items you would like to appear in your Start menu. When you’ve completed your selections, tap on OK. Managing Files and Folders Windows Embedded 6.5 files are stored in folders and sub-folders that are accessible with File Explorer.
Preliminary Draft • Tap on Start>Programs>File Explorer. Tap to display sorting options Chapter 3: Using Windows Embedded 6.5 Creating a New Folder Tap to display additional storage/files Files stored here automatically Tap to move back one level 3.4.1 Creating a New Folder • • • 3.4.2 Renaming a File • • 3.4.3 Tap Start>Programs>File Explorer. Tap Menu>New Folder in the softkey bar at the bottom of the screen. Use the EP10 keyboard or the soft keyboard to assign a name to the folder.
Chapter 3: Using Windows Embedded 6.5 Deleting a File 3.4.4 Deleting a File • • 3.5 Preliminary Draft Press and hold the stylus on the file or folder you want to delete until a pop-up menu is displayed. Tap Delete to remove the file. Using Menus In Windows Embedded 6.5, the menu is located in the softkey bar at the bottom of the screen. Softkey Bar Menu To execute a command: • 3.5.1 Tap on Menu to display the commands associated with it, and then tap on the command you want to execute.
Preliminary Draft 3.6 Chapter 3: Using Windows Embedded 6.5 The Softkey Bar • Gently press and hold the stylus on the screen. A ring of dots is displayed on the screen followed by a pop-up menu. • Tap on the command you want to execute. The Softkey Bar The EP10 is equipped with a softkey bar at the bottom of the screen. It displays softkeys that allow you to access menus and commands. It also displays the soft keyboard icon.
Chapter 3: Using Windows Embedded 6.5 The Softkey Bar Preliminary Draft The Soft Keyboard Icon Tapping on the soft keyboard icon displays an onscreen keyboard you can use as an alternative to the EP10 keyboard. Shift-State Indicator Icon The softkey bar can also display the shift-state indicator icon. This icon indicates active modifier keys–[SHIFT], [ALT], [CTRL], [ORANGE] and [BLUE]. • Tap on Start>Settings>Buttons>One Shots.
Preliminary Draft 3.7 Chapter 3: Using Windows Embedded 6.5 Programs – Using Applications Programs – Using Applications • Tap Start>Programs to display the programs installed on your EP10. Figure 3.3 Program Screen Icons Opening an Application • Tap on a Program icon to launch the associated program. Minimizing an Application • Tap on the X button in the upper-right corner of an application screen to minimize the application.
Chapter 3: Using Windows Embedded 6.5 Settings Preliminary Draft Opening, Closing and Switching Applications • Tap on Start>Settings. Tap on the System tab and then the Task Manager icon – the Task Manager screen is opened. The Task Manager screen lists all running tasks (applications). This applet provides a number of options to manage your opened applications.
Preliminary Draft Chapter 3: Using Windows Embedded 6.5 Help Figure 3.4 Settings Icons Settings are divided into three tabs – Personal, System and Connections. Refer to Chapter 5: “Settings” for details about the options available to you. 3.9 Help Tapping on the Help option displays a screen of help topics that are content-specific; if for example, the Today screen is displayed and you tap on Start>Help, the help screen will provide topics about the Today screen.
Chapter 3: Using Windows Embedded 6.5 Entering Text 3.10 Preliminary Draft Entering Text Note: For additional information about tailoring text entry using the soft keyboard, the transcriber, the block recognizer and the letter recognizer, refer to “Input” on page 107. You can enter text using either the soft keyboard or the EP10 keyboard. You can also use the Transcriber to handwrite information directly on the touchscreen using your stylus.
Preliminary Draft Chapter 3: Using Windows Embedded 6.5 The Transcriber 3.10.2 The Transcriber To access the Transcriber, with your document opened: Tap on the arrow next to the keyboard icon, and choose Transcriber from the popup menu. • Review the introductory screen. It provides some shortcut symbols you can draw on your screen to work with the Transcriber. • When you’ve finished reading the introductory screen, tap OK. The Transcriber menu and icon bars are displayed at the bottom of the document.
Chapter 3: Using Windows Embedded 6.5 Block Recognizer and Letter Recognizer Preliminary Draft Press and hold the stylus on the selected text to display a pop-up menu. Choose Cut, Copy, Paste or Clear (delete). Note: You can also use the softkey bar tools or the shortcuts listed in the introductory screen to help you edit a document within the Transcriber. 3.10.
Preliminary Draft • • Chapter 3: Using Windows Embedded 6.5 Block Recognizer and Letter Recognizer To create an uppercase character, draw a line straight up the ‘abc’ panel. Use the Recognizer Icon Bar to move around the screen, add spaces, special characters, and so on. Letter Recognizer • Open a document, and tap on the arrow next to the input icon. Choose Letter Recognizer. Input Panel Recognizer Icon Bar Input Icon There are two points to remember when using Letter Recognizer.
Preliminary Draft
Preliminary Draft 4 PROGRAMS 4.1 Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 4.2 Games . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 4.3 ActiveSync® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 4.3.1 Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 4.4 Calculator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 4.
Preliminary Draft 4.12.3 Opening a Photo . . . . . . . . . . . . . 4.12.4 Deleting a Photo . . . . . . . . . . . . . 4.12.5 Editing a Photo. . . . . . . . . . . . . . 4.12.6 Creating a Slide Show . . . . . . . . . . 4.12.7 Using the Video Recorder . . . . . . . . 4.13 Remote Desktop Mobile . . . . . . . . . . . . . . 4.13.1 Connecting to a Terminal Server. . . . . 4.13.2 Disconnecting without Ending a Session 4.13.3 Ending a Session . . . . . . . . . . . . . 4.14 Search . . . . . . . . . . . . . . . . . . .
Preliminary Draft 4.1 Chapter 4: Programs Programs Programs The Programs menu provides access to all the applications available on your EP10. • Tap on Start>Programs to display this screen. Tapping on an icon in this screen launches the associated applet. Figure 4.1 Programs Tabs 4.2 Games Your EP10 is equipped with a few standard games – Bubble Breaker and Solitaire – should you feel the need to pass the time. 4.
Chapter 4: Programs Calculator 4.4 Preliminary Draft Calculator Tapping on Start>Programs>Calculator displays a standard calculator. • 4.5 Use your stylus to tap the calculator buttons. Demo Scanner The Demo Scanner icon is used to test how the EP10 reads and writes bar codes. The Demo Scanner dialog box contains buttons at the bottom of the dialog box that allow you to Scan, Reset or change bar code Setting. 4.
Preliminary Draft Chapter 4: Programs OneNote Mobile 4.6.1.1 Workbook Components Columns Address of selected text Entry bar Cell Rows Status bar Toolbar Menu bar Selected cell Formula drop-down menu Sheet1 drop-down menu • If the toolbar is not visible, tap on the View>Toolbar. You can enter data, work with rows and columns and create formulas as you would when working with Excel on your PC.
Chapter 4: Programs OneNote Mobile Preliminary Draft Important: Remember that you must have Microsoft Office OneNote 2007 and the latest version of ActiveSync installed on your PC before you can set up a partnership between your EP10 and your PC. ActiveSync can be installed from the Getting Started CD included with your EP10. Refer to “The Getting Started CD” on page 15 for details.
Preliminary Draft Chapter 4: Programs OneNote Mobile If this is not the case, tap on Start>Programs>Office Mobile icon. Tap on the OneNote Mobile icon. • Tap on New to create a note page. Begin typing. • When you complete your note, tap on Done. Note: Remember that you can tap on the Menu softkey to Undo typing, add Formats (Bold, Italic, Underline, Strikethrough), include Lists (Numbered, Bulleted, Clear) EP10 Hand-Held (Windows Embedded 6.
Chapter 4: Programs OneNote Mobile Preliminary Draft Using the OneNote Menu Tapping on Menu displays a list of options to help you work with the OneNote Mobile applet. • • • 64 Undo, Redo, Cut, Copy and Paste: These commands operate in the same way as they do in any Windows Office application. Format: Tapping on this command lists the formatting options you can apply to your note: Bold, Italic, Underline, Strikethrough and Clear All.
Preliminary Draft Chapter 4: Programs OneNote Mobile Press [ENTER/Power] to snap a photo that is automatically inserted into your note. • Insert Picture: Tapping on this command automatically displays your My Pictures folder where you can tap on an existing picture to insert it into your note. EP10 Hand-Held (Windows Embedded 6.
Chapter 4: Programs OneNote Mobile • Preliminary Draft Insert Recording: When you tap on this command, a recording panel is displayed. Cancel Save Play Stop Record Tap on the Record button to record your message. Tap on Stop when you’ve completed your message. Tap on Play to listen to your voice message. To discard your message, tap on X – the Cancel button. To save your message, tap on OK. An audio icon is displayed in your note. You can tap on it to listen to your message.
Preliminary Draft • Chapter 4: Programs Word Mobile In Microsoft ActiveSync on your PC, choose Sync. or On your EP10, tap on Start>ActiveSync, and then tap on Sync. During synchronization, the notes you created on your EP10 are copied to a new Office OneNote 2007 notebook called OneNote Mobile on your PC. When synchronization is done, you can drag the transferred notes into any other sections and other notebooks on your PC.
Chapter 4: Programs PowerPoint Mobile Preliminary Draft Using Word Mobile Help If you need help using this application, you can review the instructions in the associated help files. To display Word Mobile help files: • • Launch the Word Mobile program. Tap on Start>Help, and review the instructions provided. 4.6.3.1 Data Entry Modes In addition to the soft keyboard, you can enter text using Block Recognizer, Letter Recognizer or Transcriber. Refer to “Entering Text” on page 52 for details.
Preliminary Draft 4.7 Chapter 4: Programs File Explorer File Explorer Windows Embedded 6.5 files are stored in folders and sub-folders that are accessible through File Explorer. You can open, save, rename, copy and paste files in the same manner as you would on any desktop PC. Important: Refer to “Managing Files and Folders” on page 44 for details about this program. 4.8 Getting Started For information about the Getting Started applet, refer to “The Getting Started Centre ??” on page 19. 4.
Chapter 4: Programs Internet Sharing 4.10 Preliminary Draft Internet Sharing This option allows you to use your EP10 to connect your PC to the Internet. Before you can use Internet Sharing, you must make certain that you have established a data connection on your EP10. 4.10.1 Creating an Internet Connection Follow the steps in this section only if you have not already setup an Internet connection.
Preliminary Draft Chapter 4: Programs Notes Tap Connect. It takes approximately 30 seconds to establish a connection. (If you are prompted to turn on Bluetooth, tap Yes.) If your are using a Bluetooth connection, execute the following steps on your PC: • • • • 4.11 Tap Start>Control Panel>Network Connections. Right-click on Bluetooth Network Connections, and click on View Bluetooth Network Devices. If the EP10 is listed as a Network Access Point, choose Connect.
Chapter 4: Programs Converting Handwritten Notes to Text Preliminary Draft To enter text with the soft keyboard, the Transcriber, the Block or the Letter Recognizer, tap the stylus on the arrow to the right on the soft keyboard icon to choose your text input method. To use your stylus to handwrite on the screen, tap on the pen icon . Important: Refer to “Entering Text” on page 52 for text entry details. • Compose your note using the method you’ve chosen. • Tap on OK when you’re done.
Preliminary Draft Chapter 4: Programs Converting Handwritten Notes to Text The text in the note is converted from handwritten to printed text. Note: To convert only a specific portion of your handwritten note into printed type, tap the stylus just before the first letter of the text, pause for a second, and then drag your stylus across the text you want to select. Then, tap on Tools>Recognize to convert only the highlighted text. Failed Conversions The Recognize tool sometimes gets the conversion wrong.
Chapter 4: Programs Renaming a Note • • Preliminary Draft Tap on the correct word in the list. If the correct word is not listed, as is the case in the sample screen above, tap on the soft keyboard icon to display the soft keyboard, and type the correct word. 4.11.3 Renaming a Note Press and hold the stylus on the file name in the Notes screen that you want to rename. In the pop-up menu, choose Rename/Move, or Tap the file name to select it, and tap on Menu>Rename/Move.
Preliminary Draft Chapter 4: Programs Synchronizing a Note A speaker icon is displayed in the note indicating the presence of a recording within the note. • To play the recorded note, tap on the speaker icon. 4.11.5 Synchronizing a Note Like Tasks, Contacts and so on, the Notes program can be synchronized with Outlook on your PC. In this way, all notes, recordings and drawings created in the Notes program are copied to your PC and can be edited in Outlook’s Notes module.
Chapter 4: Programs Using the Camera Preliminary Draft Keep in mind that if there are no pictures stored on your EP10 as yet, you’ll only see the Camera icon in this screen. • Tap on the Camera icon to activate the camera. The screen will display the image your camera is pointed at. (The camera is built into the back of the EP10.) Tapping on this softkey displays thumbnails of photos stored on the EP10. • Photo File Icon Indicates the camera is active. Frame the image in the EP10 screen.
Preliminary Draft Chapter 4: Programs Moving Photos to the EP10 Note: ‘Video’ is a toggle command. When the still camera is activated, ‘Video’ is available in this menu. When the video recorder is activated, ‘Still’ (camera) is available in this menu. 4.12.2 Moving Photos to the EP10 • • Connect your device to your PC with ActiveSync. On your PC, using Windows Explorer (right-click My Computer and click on Explorer), drag photos from their folder to the Mobile Device>My Pictures folder. 4.12.
Chapter 4: Programs Deleting a Photo • Preliminary Draft Tap on a thumbnail to open the photo. Note: If you’ve stored your photos on a storage card, you’ll need to tap on the storage card icon to display your photos. 4.12.4 Deleting a Photo • • Press and hold the stylus on the thumbnail photo you want to delete to display a pop-up menu. Tap on Delete. Confirm your choice when prompted. 4.12.5 Editing a Photo • Tap a thumbnail photo to open it. • Tap on Menu>Edit.
Preliminary Draft • Chapter 4: Programs Using the Video Recorder To display the slide show tool bar, tap anywhere on the photo. Pause Play Flip View Previous Next Close 4.12.7 Using the Video Recorder • Tap on the Camera icon. EP10 Hand-Held (Windows Embedded 6.
Chapter 4: Programs Remote Desktop Mobile Preliminary Draft • In the bottom-right corner of the camera screen, tap on Menu>Video. • Press [ENTER/Power] to begin recording. Video Recorder Icon Indicates that video is active. • To end the video, press [ENTER/Power] again, or tap on the Stop softkey. Note: When the ‘Video’ recorder is activated, a Menu is available to tailor the operation of the recorder, the quality of the recording, and so on. 4.
Preliminary Draft Chapter 4: Programs Connecting to a Terminal Server 4.13.1 Connecting to a Terminal Server • • • • Tap on Start>Programs>Remote Desktop Mobile In the Server dialog box, type the Terminal Server name or TCP/IP address, or choose a server from the drop-down menu. Tap on Connect. In the Remote Desktop Connection window, type your user name, password, and domain (if required). Tap on OK. 4.13.
Chapter 4: Programs Search 4.14 Preliminary Draft Search 4.15 • Tap Start>Programs, and then tap on the Search icon. • • In the Search for field, type the item for which you’re looking. To narrow your search, tap on the Type drop-down menu and choose from a list of preexisting programs. To search through all files, leave this option at All Data. Task Manager Refer to “Task Manager” on page 145 for details about this applet. 4.
Preliminary Draft Chapter 4: Programs Browsing Web Sites You can connect to Internet Explorer in two ways: by connecting the EP10 directly to the Internet or by connecting through your PC while the EP10 is attached via ActiveSync (see “ActiveSync®” on page 59). 4.17.1 Browsing Web Sites There is little difference between the standard Internet Explorer found on your PC and that found on your EP10, sometimes referred to as Pocket Internet Explorer.
Chapter 4: Programs Messaging 4.18 Preliminary Draft Messaging Note: Messaging is available from the Start menu by default. If you prefer it only be accessed from the Programs window, tap on Start>Settings, tap on the Menus icon and uncheck Messaging. The Messaging program is used to send and receive e-mail on your EP10. To send and receive e-mail, you’ll need to synchronize your PC or connect to a Post Office Protocol 3 (POP3) or Internet Message Access Protocol 4 (IMAP4) mail server.
Preliminary Draft • Chapter 4: Programs Synchronizing E-mail with Outlook In ActiveSync on your PC, tap on Tools>Options in the tool bar at the top of the screen. • Make certain that a check mark is displayed in the checkbox next to E-mail. Tap on OK. Once you check E-mail for synchronization, Outlook e-mail messages are synchronized as part of the general synchronization process.
Chapter 4: Programs Changing Synchronization Settings Preliminary Draft 4.18.3 Changing Synchronization Settings • In ActiveSync on your PC, double-tap the E-mail item in the Sync Options tab. • Tap on the Select Folder button. • Add a checkmark next to the folders in this screen that you want to synchronize with your EP10, and tap on OK. The E-mail Synchronization screen is displayed again. • • 86 If you want to accept file attachments, add a check mark next to Include file attachments.
Preliminary Draft 4.19 Chapter 4: Programs Windows Media Windows Media Windows Media allows you to play music and videos on your EP10. You can use Windows Media to play digital audio and video files that are stored on your EP10 or on the Web. • • To work with this applet, tap on Start>Programs>Windows Media. To find detailed instructions about this option, tap on Start>Help, and in the list of help files, tap on Use Windows Media Player Mobile. EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft
Preliminary Draft 5 SETTINGS 5.1 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 5.2 Personal Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 5.3 App Launch Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 5.4 Buttons Icon . . . . . . . . . . . . . . 5.4.1 Up/Down Control . . . . . . 5.4.2 Sequence . . . . . . . . . . . 5.4.3 One Shots. . . . . . . . . . . 5.4.4 Keyboard Macro Keys . . . . 5.4.
Preliminary Draft 5.14 About Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 5.15 Backlight . . . . . . . . . . . . 5.15.1 Battery Power . . . . 5.15.2 External Power . . . . 5.15.3 Intensity . . . . . . . 5.16 Certificates . . . . . . . . . . . 5.16.1 Choosing a Certificate 5.17 Clock & Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preliminary Draft 5.31 Teklogix Error Handling Service 5.31.1 ErrorLogInfo . . . . . 5.31.2 NetLog . . . . . . . . 5.32 Teklogix Imagers Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147 .147 .148 .149 5.33 Scanner Settings. . . . . . . . . . . . . . . . . . . 5.33.
Preliminary Draft 5.39.7 About Tab . . . . . . . . . . . . . . . . . . . . . . 5.39.8 The Bluetooth GPRS Phone . . . . . . . . . . . . . 5.40 Connection Properties . . . . . . . . . . . . . . . . . . . . . 5.40.1 Port Settings . . . . . . . . . . . . . . . . . . . . . 5.40.2 Call Options . . . . . . . . . . . . . . . . . . . . . 5.41 Connections – Connecting to the Internet . . . . . . . . . . . 5.41.1 Modem Connection Setup . . . . . . . . . . . . . . 5.41.1.1 Advanced Modem Settings . . . . . . . . . 5.
Preliminary Draft 5.44.6.2 Inbox . . . . . . . . 5.44.6.3 Outbox . . . . . . . 5.44.6.4 SMS Configuration 5.45 Windows Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EP10 Hand-Held (Windows Embedded 6.5) User Manual . . . . .210 . 211 .212 .
Preliminary Draft
Preliminary Draft 5.1 Chapter 5: Settings Settings Settings The Settings screen is divided into three tabs – Personal, System and Connections. • Tap on Start>Settings to display this screen. Figure 5.1 Settings Tabs 5.2 Personal Settings The Personal tab allows you to tailor the general behaviour of your EP10 such as defining input methods, Start menu options, owner information, password assignment, sound specifications, and so on. 5.
Chapter 5: Settings App Launch Keys • Preliminary Draft Tap on Start>Settings, and then tap on the App Launch Keys icon. To assign an application key: 96 • Tap the Add button. • Press the key you want to use to launch an application. (If an unsupported key is pressed, a message appears on this screen letting you know.) EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft Chapter 5: Settings App Launch Keys The cursor moves to the App field and a new screen is displayed where you can choose the application to which you want to assign the application key. If you need to, you can Browse through the information in your EP10 until you locate the application you want to launch. • Once you’ve selected the file you want to map, tap on OK. The cursor moves to the Data field.
Chapter 5: Settings Buttons Icon 5.4 Preliminary Draft Buttons Icon • Tap on Start>Settings, and then tap on the Buttons icon to display your options. Note: The ‘Program Buttons’ option is not available on the EP10. 5.4.1 Up/Down Control Sliding the Delay before first repeat bar to the left decreases the delay between key repeats while sliding the bar to the right increases the repeat delay time.
Preliminary Draft 5.4.2 Chapter 5: Settings Sequence Sequence This slider determines the allowable pause between alpha key presses on a keypad. For example, suppose you want to type the letter ‘c’ – you would need to press the [2] key three times. With the [ORANGE] key locked ‘on’, if you press [2] twice and then pause between key presses for 1 second, the letter ‘b’ will be selected automatically. Moving the Sequence slider to the right increases the pause time between alpha key presses. 5.4.
Chapter 5: Settings One Shots Preliminary Draft Important: Once you’ve assigned a One Shot mode to a modifier key, you need to tap on the OK button at the top of the tab to activate your selection. Lock If you choose Lock from the drop-down menu, pressing a modifier key once locks it ‘on’ until you press the modifier key a second time to unlock or turn it off. OneShot If you choose OneShot, the modifier key remains active only until the next key is pressed.
Preliminary Draft 5.4.4 Chapter 5: Settings Keyboard Macro Keys Keyboard Macro Keys Macro keys are not labelled on the keypad. However, you can map up to 12 macro functions using the keyboard remapping function described in “Scancode Remapping” on page 103. A macro has 20 programmable characters (or “positions”). The macro keys can be programmed to replace frequently used keystrokes, along with the function of executable keys including [ENTER/Power] and [BKSP], function keys, and arrow keys.
Chapter 5: Settings Unicode Mapping Preliminary Draft • When you’ve finished recording your macro sequence, tap on Stop Recording. A new screen – Verify Macro – displays the macro sequence you created. • • Tap on the Save button to save your macro. Your macro key sequence is listed in the Macro screen. Tap on OK to save your macro key assignment. Executing a Macro • Press the macro key to which you’ve assigned the macro to execute it. Deleting a Macro • • 5.4.
Preliminary Draft Chapter 5: Settings Scancode Remapping Adding and Changing Unicode Values Important: Changes to Unicode mappings are not saved until you exit the Unicode Mapping tab by tapping on [OK]. • Tap on the Add/Change button. • • Highlight a value in the Unicode mapping list. Position the cursor in the Unicode Mapping field, and type a Unicode value for the highlighted key.
Chapter 5: Settings Scancode Remapping Preliminary Draft There are three different tables of scancode mappings: the Normal table, the Blue table and the Orange table. The Normal table defines unmodified key presses; the Blue table defines key presses that occur when the [BLUE] modifier is on; the Orange table defines key presses that occur when the [ORANGE] modifier is on. The default mappings of these scancodes can be overwritten for each of these three tables using the Scancode Remapping tab.
Preliminary Draft Chapter 5: Settings Scancode Remapping The Remap Scancode dialog box is displayed. • Type the scan code in hexidecimal in the field labelled Scancode. Note: The ‘Label’ field displays the default function of the scancode you are remapping. Virtual Key, Function and Macro The radio buttons at the bottom of the dialog box allow you to define to what the scan code will be remapped to: Virtual Key, Function or Macro.
Chapter 5: Settings Lock Sequence Preliminary Draft Removing a Remap • • 5.4.7 In the Scancode Remapping tab, highlight the scancode you want to delete, and tap on the Remove button. Tap on OK. Lock Sequence The Lock Sequence tab allows you to lock the EP10 keyboard to prevent keys from being pressed accidentally when, for example, the unit is inserted in a holster. • To lock the keyboard, tap in the checkbox next to Enable key lock sequence.
Preliminary Draft Chapter 5: Settings Input A locked keyboard icon is displayed in the softkey bar when the keyboard is locked. Locked Keyboard Icon • 5.5 To unlock the keyboard, type the key sequence again. Input The Input icon provides access to text input options you can use to tailor the soft keyboard, block recognizer, letter recognizer and transcriber along with voice recording options. EP10 Hand-Held (Windows Embedded 6.
Chapter 5: Settings Input Method Tab 5.5.1 Preliminary Draft Input Method Tab • Tap on Start>Settings and then on the Input icon to display your options. A drop-down menu next to Input method allows you to tailor your methods of input – Block Recognizer, Keyboard, Letter Recognizer and Transcriber. Block Recognizer Block Recognizer teaches you how to conform your handwriting to what the EP10 can recognize. Important: Refer to “Block Recognizer and Letter Recognizer” on page 54 for additional details.
Preliminary Draft Chapter 5: Settings Input Method Tab Keyboard Options This screen is displayed when you choose Keyboard in the Input method drop-down menu. You can use it to customize the soft keyboard. You can choose Large Keys or Small Keys to increase or decrease the size of the keys displayed on the soft keyboard. If you enable Use gestures for the following keys, these keys are removed from the soft keyboard. Gestures are handwriting shortcuts for the keyboard keys.
Chapter 5: Settings Input Method Tab Preliminary Draft Figure 5.2 Letter Recognizer Quick Settings These options allow the Letter Recognizer to better interpret any specialized strokes and accents you may wish to use. Transcriber Options Note: Before you can display the Options for Transcriber, you need to select Transcriber as the active input method. Tap on the arrow to the right of the keyboard icon in the taskbar, and choose Transcriber.
Preliminary Draft Chapter 5: Settings Input Method Tab Inking In the Inking tab, you are presented with a number of options. Recognition Delay allows you to determine the time delay between writing something on the Transcriber screen and its recognition into printed text. Enabling Add space after automatically adds a space after each word you write. The Pen option allows you to choose the line Width and Colour.
Chapter 5: Settings Options–Additional Choices Preliminary Draft 5.5.1.1 Word Completion This tab speeds the writing process regardless of the input method chosen. When you begin entering a word, this option displays what it assumes is the complete word, saving you having to type the word in its entirety. You can also tailor how and when you want word suggestions made. 5.5.
Preliminary Draft 5.6 Chapter 5: Settings Lock Lock To protect the data stored in your EP10, you can assign a password that must be entered each time the unit is switched on. • Tap on Start>Settings, and then tap on the Lock icon. It is critical that you store your password in a safe place. If you forget it, a ‘clean start’ must be performed by certified Psion Teklogix personnel. A clean start returns the EP10 to factory settings. Only the data stored in a CF or SD memory card are preserved.
Chapter 5: Settings Menus 5.7 Preliminary Draft Menus The Menus icon allows you to display options to customise the Start Menu. • 5.7.1 Tap on Start>Settings and then tap on the Menus icon. Start Menu Tab This tab allows you to define the items that will be listed in your Start menu. • In the Start Menu dialog box, tap on the items you want to appear in your Start menu. The checked items will be listed in your Start menu. 114 EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft 5.8 Chapter 5: Settings Owner Information Owner Information Tapping on Start>Settings and then tapping on the Owner Information icon allows you to add your personal information to the EP10. Some of this information will be displayed in the desktop Today screen. Important: Refer to “Ownership Information” on page 36 for details about this option. EP10 Hand-Held (Windows Embedded 6.
Chapter 5: Settings Phone 5.9 Preliminary Draft Phone Tapping on Start>Settings and then tapping on the Phone icon allows you to adjust phone settings such as the ring type and tone, choose phone services such as barring calls, and you can also determine network selections. Important: Refer to “Managing Phone Settings” on page 39 for details about this option. 5.10 Sound & Notifications The Sounds & Notifications icon allows you to specify when your EP10 will emit sounds.
Preliminary Draft Chapter 5: Settings Sounds 5.10.1 Sounds • Tap on Start>Settings, and then tap on the Sounds & Notifications icon to display this dialog box. • Tap in the checkboxes and radio buttons to enable the event(s) that will cause your unit to emit a sound. 5.10.2 Notifications Tap here to play your ring choices Tap here to end the ring test This tab allows you to determine how you are notified about different events. • • Choose an event from the Events drop-down menu.
Chapter 5: Settings Today Screen 5.11 Preliminary Draft Today Screen This option allows you to tailor the appearance of the Today screen – the desktop screen. • Tap on Start>Settings, and then tap on the Today icon. 5.11.1 Appearance This screen allows you to customize the background displayed on the Today screen. • Choose the background you want to use from the list. 5.11.2 Items This tab allows you to choose and to sort the item(s) that you want listed in the Today screen.
Preliminary Draft • • 5.12 Chapter 5: Settings System Tab Settings Tap in the checkbox to the left of the item(s) you want displayed in the Today screen. To rearrange the list of items, highlight the item you want to move up or down and tap on the Move Up or Move Down button. Keep in mind that the Date cannot be moved. System Tab Settings To display the icons grouped in the System tab: • 5.13 Tap on Start>Settings, and tap on the System tab.
Chapter 5: Settings About Device 5.14 Preliminary Draft About Device Tapping on the About Device icon under Settings>System tab provides access to three tabs related to your EP10. The Properties tab lists hardware information related to your EP10. The Copyrights tab lists the copyrights that apply to your EP10. The Experience tab allows you to choose a category to help you define your Experience. These categories include Microsoft settings, Psion Teklogix settings and Custom settings in a drop-down menu.
Preliminary Draft • Chapter 5: Settings External Power To Turn on backlight when a button is pressed or the screen is tapped, tap in the checkbox to the left of this option. 5.15.2 External Power This tab determines the behaviour of the backlight when the EP10 is using external rather than battery power. Important: Refer to “Battery Power” on page 120 for details about these options. 5.15.3 Intensity This tab is used to adjust the light intensity of the display backlight and the keyboard backlight.
Chapter 5: Settings Certificates 5.16 Preliminary Draft Certificates A public key is transmitted as part of a certificate. The certificates listed in the Certificates tabs ensure that the submitted public key is, in fact, the public key that belongs to the submitter. The EP10 checks that the certificate has been digitally signed by a certification authority that the EP10 explicitly trusts. Your EP10 has certificates already preinstalled in the unit.
Preliminary Draft Chapter 5: Settings Certificates Intermediate Certificates The items in this list help identify intermediate certification authorities. Root Certificates • • • To view details about a certificate – who issued the certificate, to whom it was issued, the issue date and the expiry date – tap on a certificate in the list. To delete a certificate, tap and hold the stylus on the certificate you want to delete. In the pop-up menu, tap on the Delete command.
Chapter 5: Settings Choosing a Certificate Preliminary Draft 5.16.1 Choosing a Certificate Normally, certificates already configured for your network are chosen automatically by the EP10. If a certificate cannot be chosen automatically, you must choose it from the Certificates list. • 5.17 To choose a certificate, tap the desired certificate. Your EP10 will connect automatically.
Preliminary Draft Chapter 5: Settings Encryption Note: If you want to make this option inaccessible, go to Start>Settings and tap on the About Device icon. In the Experience tab, remove the checkmark to the left of Enable Customer Feedback and SQM (reset required). As indicated, you’ll need to reset the EP10. 5.19 Encryption This option allows you to encrypt the data on your storage card. EP10 Hand-Held (Windows Embedded 6.
Chapter 5: Settings Error Reporting • 5.20 Preliminary Draft Tap on Start>Settings>System tab>Encryption icon. Error Reporting Error Reporting allows you to enable or disable Microsoft error reporting prompts. • 126 Tap on Start>Settings. Tap on the System tab followed by the Error Reporting icon. EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft 5.21 Chapter 5: Settings GPS (Global Positioning System) GPS (Global Positioning System) With a Global Positioning System (GPS) receiver, you can locate your exact position on a map. However, even without a GPS receiver, several different mapping programs can run on your EP10. • Tap on Start>Settings>System tab>GPS icon. • Tap on the GPS program port drop-down menu, and choose the communication (COM) port that the GPS software will use to communicate with the GPS receiver.
Chapter 5: Settings GPS (Global Positioning System) Settings • Preliminary Draft Tap on the Hardware tab, and choose a GPS hardware port and the appropriate Baud rate. Windows Embedded 6.5 automatically manages access to the GPS receiver. However, some programs may not work with automatic configuration. If this is the case: • Tap on the Access tab, and disable Manage GPS automatically (recommended). You can go to www.microsoft.
Preliminary Draft Chapter 5: Settings GPS (Global Positioning System) Settings • Tap on Start>Settings>System tab>GPS Settings icon. Power Tab This tab allows you to dictate how the GPS module behaves. The GPS Power drop-down menu is used to control when the GPS is powered on and off. • • • • Off – the GPS module is left off, always. Always on – the GPS module is powered on at all times regardless of the power state of the EP10 (suspend or standby).
Chapter 5: Settings GPS (Global Positioning System) Settings Preliminary Draft Profiles Tab Tapping on the GPS Profile Selection drop-down menu allows you to choose an appropriate profile: Default, Automotive or Pedestrian. • • • 130 Default profile is a good general profile suitable for most uses. Automotive profile is designed for in-vehicle use, providing quick location updates as the vehicle moves.
Preliminary Draft Chapter 5: Settings GPS (Global Positioning System) Settings AGPS (Assisted Global Positioning System) Tab To determine your location, a GPS module receives data from three or more GPS satellites in fixed orbit around the Earth. The GPS module triangulates your location based on the time it takes for signals to get to and from the satellites. This works well in fairly clear areas – outdoors, for example.
Chapter 5: Settings GPS (Global Positioning System) Settings Preliminary Draft Settings • Click on the Settings button to define the AGPS server connection settings. The AGPS server connection settings drop-down menu allows you to choose from two settings: Use default settings and Use custom settings. The Use default settings option is generally acceptable for most applications.
Preliminary Draft Chapter 5: Settings Manage Triggers Info Tab This tab provides general information about the GPS module such as the firmware version, the date on which files were last updated, and so on. If GPS module support service is required, you may be asked to tap on the Save button in this tab and forward the information to Psion Teklogix support staff. 5.23 Manage Triggers Manage Triggers allows you to configure how bar code scanners and other devices are triggered.
Chapter 5: Settings Trigger Mappings • Preliminary Draft Tap on Start>Settings>System tab>Manage Triggers icon. 5.23.1 Trigger Mappings A trigger mapping is an association between a particular key on the keyboard and a driver or application, the module(s) – sometimes referred to as “trigger consumer(s)” – of the trigger source. Along with keyboard keys, trigger sources can also be grip triggers, external hardware triggers or software-based.
Preliminary Draft Chapter 5: Settings Trigger Mappings Show All Modules By default, the trigger mapping list only shows active mappings. Mappings for drivers or applications that are not currently active are not normally displayed. By checking this checkbox, all mappings, both active and inactive, are displayed. Add Tapping this button brings up the Add mapping dialog (see below), so that you can add new trigger mappings.
Chapter 5: Settings Trigger Mappings Preliminary Draft Note: It is possible to map the same source to different modules (trigger consumers) – for example, to both the Imager and Non-Decoded Scanner. If so, both devices/operations will occur simultaneously. This is not recommended in most cases, especially with devices such as Imagers. It is also possible to map different sources to the same module (trigger consumer). Add Key Only existing trigger sources are shown in the Source combo-box.
Preliminary Draft 5.24 Chapter 5: Settings Managed Programs Managed Programs Managed Programs lets you view, download and install applications that are deployed by the System Center Mobile Device Manager (a server-side solution that helps enable IT to have control of their device deployment with respect to security, management and access to the corporate network). To access Managed Program: • Tap on Start>Settings>System tab>Managed Programs icon.
Chapter 5: Settings Main Tab Preliminary Draft 5.25.1 Main Tab This tab lists the memory allocated for file and data storage and for program storage. 5.25.2 Storage Card The Storage Card screen indicates the total storage card or RAM disk memory along with the amount in use. 5.26 Power Icon This icon allows you to view and manage battery use. • 138 Tap on Start>Settings. Tap on the System tab followed by the Power icon. EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft Chapter 5: Settings Battery Tab 5.26.1 Battery Tab This tab allows you to view the remaining battery capacity. 5.26.2 Advanced Tab The Advanced tab allows you to manage battery consumption. On Battery Power When the EP10 is operating on battery power, this option allows you to determine how long the unit will remain on when it is not in use. EP10 Hand-Held (Windows Embedded 6.
Chapter 5: Settings Battery Details • Preliminary Draft Tap in the checkbox to the left of On battery power to enable this option. Tap in the drop-down menu to choose the number of minutes your unit can remain idle before it shuts down. On External Power When the EP10 is drawing external rather than battery power, this option allows you to determine the number of minutes the unit will remain on when not in use. • Tap in the checkbox to the left of On external power to enable this option.
Preliminary Draft Chapter 5: Settings Built-In Devices 5.26.4 Built-In Devices Built-In Devices Checking the box next to Enable Bluetooth switches on the built-in Bluetooth radio. 5.26.5 Card Slots When you select one or more of the card slots listed, power is supplied to the enabled slot(s). Clicking on the Apply button activates your selections. Keep in mind that if the characters on this button appear in grey typeface, the checked slots have already been enabled.
Preliminary Draft Chapter 5: Settings Suspend Threshold and Estimated Battery Backup 5.26.6 Suspend Threshold and Estimated Battery Backup The Estimated Battery Backup is the amount of battery power that has been reserved or set aside to protect data until a fully charged battery can be installed in the EP10.
Preliminary Draft Chapter 5: Settings Suspend Mode 5.26.7 Suspend Mode When this option is enabled, any time the EP10 enters suspend mode (e.g., an idle time out, Power button press or through the Start menu), Go to standby on suspend forces the EP10 to enter Standby mode. In Standby mode, applications, processors and services (e.g., Bluetooth) continue to run even while the EP10 is powered down, making them instantly available when the unit is powered up again. 5.
Chapter 5: Settings Remove Programs Preliminary Draft • Tap on the drop-down menu to choose your language and region. Once you’ve selected a language and region, you may need to adjust the way numbers, currency, the time and the date appear in your EP10. • 5.28 Tap on the tab associated with each of the items and choose how each item should be displayed on your EP10. Remove Programs • Tap on Start>Settings. Tap on the System tab followed by the Remove Program icon.
Preliminary Draft • Chapter 5: Settings Task Manager Tap Start>Settings. Tap on the System tab, and then tap on the Screen icon. Important: Refer to “Aligning (Calibrating) the Touchscreen” on page 20 for details. 5.30 Task Manager The Task Manager screen lists all running tasks (applications) or processes. This applet provides a number of options to manage these. EP10 Hand-Held (Windows Embedded 6.
Chapter 5: Settings Task Manager Preliminary Draft • Tap on Start>Settings. Tap on the System tab and then the Task Manager icon – the Task Manager screen is opened. • End Task: To shut down an application, highlight the program in the list, and tap on the End Task softkey in the taskbar at the bottom of the screen. Task Manager Menu The Task Manager menu provides additional options to help you manage your applications. 146 • Tap on the Menu softkey in the taskbar.
Preliminary Draft • • • • • 5.31 Chapter 5: Settings Teklogix Error Handling Service End All Tasks: Shuts down all applications listed. View: Allows you to list either all running applications or all processes. Sort By: Allows you to sort active applications or processes based on Memory size, CPU or application or process Name. Refresh: Updates the list of applications or processes. Exit: Closes the Task Manager. Teklogix Error Handling Service • Tap on Start>Settings.
Chapter 5: Settings NetLog Preliminary Draft • Choose an Error Level, and tap on FlushToFile to log the information file. Psion Teklogix personnel can help you retrieve and forward the information file to our offices. 5.31.2 NetLog The NetLog option is used to log network traffic. When you tap in the checkbox to the left of Enable NetLog Debug Capturing, debug data is collected so that, if necessary, it can be forwarded to a Psion Teklogix technician for evaluation.
Preliminary Draft 5.32 Chapter 5: Settings Teklogix Imagers Settings Teklogix Imagers Settings The Teklogix Imagers applet is used to create, modify, delete and activate imager settings. The principle uses of the applet are to decode bar codes and to capture images. Note: This icon is only when displayed when the HHP 5000 imager is installed in your EP10 hand-held. To launch this applet: • Tap on Start>Settings>System tab, and then tap on the Teklogix Imagers icon.
Chapter 5: Settings Scanner Settings Preliminary Draft To launch the demo: • 5.33 Tap on Start>Programs, and then tap on the PTSI Imager icon. Scanner Settings The Teklogix Scanners icon in the Settings menu provides access to dialog boxes in which you can tailor bar code options and choose the bar codes your scanner will recognize. 150 EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft • Chapter 5: Settings Bar Code Settings – The Scanner Menu Tap on Start>Settings, and then tap on the System tab followed by the Teklogix Scanner icon. 5.33.1 Bar Code Settings – The Scanner Menu The drop-down menu to the right of the Scanner option allows you to choose from one of the following scanner types used with your EP10: Decoded (internal), Decoded (Intermec ISCP) or Imager. The symbologies listed change to reflect the scanner you choose and the bar codes it supports.
Chapter 5: Settings Options Tab Preliminary Draft 5.33.2 Options Tab This tab allows you to tailor the double-click parameters and the display options associated with your scanner. 5.33.2.1 Double Click Parameters Click Time (msec) This parameter controls the maximum gap time (in milliseconds) for a double-click. If the time between the first and second clicks of the scanner trigger is within this time, it is considered a double-click. The allowable range is 0 to 1000.
Preliminary Draft Chapter 5: Settings Options Tab 5.33.2.2 Display Parameters Scan Result When this parameter is enabled, the type of bar code and the result of the scan appear on the screen. Note that this information is only displayed after a successful decode and is visible only while the scanner trigger is pressed. When the trigger is released, this information is cleared from the screen.
Chapter 5: Settings Translations Tab Preliminary Draft 5.33.2.3 Data Handling This option allows you to choose the code page your EP10 will use to display data – Default Local ASCII or ISO-8859-1 Latin 1. Codepage: Tapping on this option displays a window in which you can define the code page your EP10 will use. If you choose Default Local ASCII, the code page of the local OS is used.
Preliminary Draft • Chapter 5: Settings Translations Tab In the Translations tab, tap on a Case # to create rules. EP10 Hand-Held (Windows Embedded 6.
Chapter 5: Settings Translations Tab • Preliminary Draft Tap on the No rule drop-down menu to display the rules. When you choose a rule, an associated screen is displayed in which you can define the rule. 5.33.3.1 Case Rules The case rules are defined as follows: • • • • • 156 No rule – ignored. Match at index – matches the match string at a specified index. Match and replace at index – matches the match string at a specified index and replaces/changes it.
Preliminary Draft • • Chapter 5: Settings Ports Tab Verify barcode size – verifies the bar code size. This rule should generally be assigned first, before creating subsequent rules. Search and replace – replaces all instances of the match string. (Note that this rule cannot fail.) Warning: Keep in mind that the effects of previously applied rules must be taken into account when creating subsequent rules.
Chapter 5: Settings Ports Tab Preliminary Draft 5.33.4.1 Port Replicator Port A (COM5:) Enabled This parameter allows you to turn this port on (enable) and off. Baud Double-tapping on this parameter displays a pop-up window in which you can choose an appropriate baud rate. Data Bits This parameter determines the number of data bits included in each asynchronous data byte. Most devices use 8 bit data bytes.
Preliminary Draft Chapter 5: Settings Ports Tab Parity This parameter determines the type of parity checking used on the data going through the tether port. Double-tapping on this option displays a pop-up window in which you can choose the appropriate Parity. Stop Bits This parameter specifies the number of stop bits – 1, 1.5, 2 – used for asynchronous communication.
Chapter 5: Settings Total Recall Preliminary Draft Double-tapping on Trigger On Sequence or Trigger Off Sequence displays a screen with a hex array of 10 elements. These parameters work in conjunction with Manage Triggers sending on and off data streams to the trigger module you assigned. For example, supposed you launch Manage Triggers and choose Decoded Scanner as the ‘module to trigger’. Next, you assign a ‘trigger key’ – for this example, a period (‘.’).
Preliminary Draft • Chapter 5: Settings Creating a Backup Profile Tap on Start>Settings. Tap on the Total Recall icon. In the drop-down menu, you can choose: Create Backup Profile, Restore Selected Profile, View Selected Profile Data, and Delete Selected Profile. Keep in mind that until a profile is created, only one option is available – Create Backup Profile. 5.34.1 Creating a Backup Profile • Tap on the Next button to begin the process.
Chapter 5: Settings Creating a Backup Profile • Preliminary Draft Next, choose the Profile Type you want to create: - For this device only – creates a backup that is manually restored by the operator. - AutoRestore for this device only – creates a profile that automatically restores itself following a cold start. • • Finally, choose a Profile Location. Tap on the Next button to display the next dialog box, Add Files.
Preliminary Draft Chapter 5: Settings Creating a Backup Profile View Selections Depending on what you have selected for inclusion in your profile, you can view a list of all files, selected files, databases, and/or the registry. • If you’re satisfied with the items in the profile, tap on Next. Performing the Backup • Tap on Backup to begin the process and create a profile. When the backup is finished, a dialog box is presented stating that the backup has been completed successfully.
Chapter 5: Settings Restoring a Profile Preliminary Draft 5.34.2 Restoring a Profile To manually restore a profile: • • 5.35 Choose Restore Selected Profile from the drop-down menu, and choose the Profile Name you want to restore. In the next screen, tap on Restore to restore your profile. TweakIT This utility allows you to ‘tweak’ or adjust Advanced system settings (interface, network and servers), User settings (font size and docking port message), and provides a Registry Editor.
Preliminary Draft Chapter 5: Settings Advanced Interface And Network 5.35.1 Advanced Interface And Network Enable IPv6 This option allows you to enable Internet Protocol, version 6, that has been published to use 128-bit IP address (replacing version 4). Modem Logging When this option is enabled, the EP10 logs AT commands (e.g., dial-out information, password string, etc.) that the administrator can monitor for debugging purposes. Modem commands are stored in: \MdmLog.txt.
Chapter 5: Settings Advanced Services Settings Preliminary Draft 5.35.2 Advanced Services Settings FTP Server This option is enabled by default to allow file transfers. Keep in mind that data transfer in either direction is restricted to the Temp folder – that is, data are always loaded from the FTP Server to the Temp folder and from the Temp folder to the FTP Server. If this option is disabled, a warm reset must be performed to accept the change.
Preliminary Draft Chapter 5: Settings Radio Features 5.35.3 Radio Features AP Density This option allows you to determine the signal strength at which the EP10 radio will begin searching for a new Access Point (AP): High, Medium or Low. If this option is set to High, the radio will begin searching for a new Access Point while still at a fairly strong signal strength.
Chapter 5: Settings User System Setting Preliminary Draft enters sleep mode when no activity is detected to reduce power consumption. Another benefit is that when Radio Power Management is enabled, even when no activity is detected, the access point does not disassociate the EP10. 5.35.4 User System Setting Docking Port Message Checking this box blocks the message that normally pops up on the display when the EP10 is docked. 168 EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft Chapter 5: Settings Registry Editor 5.35.5 Registry Editor This option is reserved for senior administrators who have a strong understanding of registry keys and values. Careless registry editing can cause irreversible damage to the EP10. 5.36 Windows Update This program checks for software updates, and if found, downloads updates to your EP10. You can choose to have updates checked automatically, or if you prefer, you can determine when your unit will check for updates. 5.
Chapter 5: Settings Navigation Bar Hotkeys • Preliminary Draft Tap on Start>Settings>Connections tab to display your connection options. Navigation Bar Tap on these connectivity hotkeys to display Notification Bubbles Notification Bubble 5.37.1 Navigation Bar Hotkeys Some of the connectivity icons in the Navigation Bar along the top of the screen are hotkeys that offer shortcuts to connection setups.
Preliminary Draft Chapter 5: Settings Navigation Bar Hotkeys Automatic Network Detection If a wireless network is available when you switch on your hand-held, a notification bubble may appear letting you know which networks have been found. You can choose a network from here. Network Detection Icon Tapping on Connect in the softkey bar at the bottom of the screen will automatically connect to a network that’s already been set up.
Preliminary Draft Chapter 5: Settings Beam displays a group of notification icons – in the sample screen below, a missed call icon and a new voice message icon. Multiple Notification Icon Missed Call Icon New Voice Message Icon Tapping on any of these icons displays an associated notification bubble with information about and access to the missed call(s) or voice message(s). 5.38 Beam This option is not available for the EP10. 5.
Preliminary Draft Chapter 5: Settings The Devices Tab 5.39.1 The Devices Tab This tab allows you to scan for other Bluetooth enabled devices, and it allows you to pair devices. Note: You may need to enable your Bluetooth radio before you begin. Refer to “Bluetooth Mode” on page 176 for details. To add a new device: • Tap on Add new device.... The EP10 scans for a Bluetooth device within a 10 meter range.
Chapter 5: Settings The Devices Tab • Preliminary Draft Highlight the device you want to add. Tap on Next. • If required, type your Passcode. If not, skip this step and just tap on Next. A pop-up message lets you know that your device has been connected to your EP10. 174 EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft Chapter 5: Settings The Devices Tab • To change the Display Name, tap on the Advanced button. This is an optional step. • Tap on Save. Note: To connect to a Bluetooth-equipped device that’s already been added, tap on the item in Bluetooth list box. 5.39.1.1 Pairing a Device If you intend to pair devices (a headset, for example), power on and bring the device within 10 meters of the EP10 before proceeding with the discovery process described below.
Chapter 5: Settings Bluetooth Mode Preliminary Draft 5.39.2 Bluetooth Mode • Tap Start>Settings. Tap on the Connections tab following by the Bluetooth icon. Next, tap on the Mode tab. When Turn on Bluetooth is checked, Bluetooth features are available. If this option is disabled, you cannot send or receive information using Bluetooth.
Preliminary Draft Chapter 5: Settings Bluetooth COM Ports 5.39.3 Bluetooth COM Ports New Outgoing Port When you pair the EP10 with another device, New Outgoing Port is listed in this dialog box. Tapping on this option allows you to assign an outgoing COM port number. • To work with an existing COM port number, tap and hold the stylus on an existing port. To assign a new port number, make certain that your EP10 is connected to the other device via Bluetooth.
Chapter 5: Settings Outgoing Port Preliminary Draft 5.39.4 Outgoing Port Outgoing Port acts as a serial port that can be used to connect to a list of Bluetooth devices (one at a time). This tab allows you to assign and enable an outgoing port and choose the device with which you want to communicate from the list. You can also tailor the behaviour of your EP10 so that you are prompted to choose the device with which you want to communicate. 5.39.
Preliminary Draft Chapter 5: Settings Active Connections You can assign either a BSP or a COM prefix from the drop-down menu. BSP (Bluetooth Serial Port) was created by Microsoft to allow Bluetooth to have its own serial prefix in order to free up virtual COM prefixes as these are limited and are widely used. (In Windows Embedded 6.
Chapter 5: Settings About Tab Preliminary Draft 5.39.7 About Tab The About tab displays information about the Bluetooth module, such as the manufacturer name, local address and version. Like the Active tab, this information cannot be edited. 5.39.8 The Bluetooth GPRS Phone Once you’ve completed the Bluetooth settings, you can go ahead and set up communication through your Bluetooth-equipped phone.
Preliminary Draft Chapter 5: Settings The Bluetooth GPRS Phone 3. Type a name for the connection. 4. Tap on the Select a modem drop-down menu, and choose Bluetooth. Tap on Next. 5. Make certain that the phone is discoverable. Some phones also need to be pairable in order to accept a bonding request. Refer to your phone documentation for additional information. 6. If the phone appears in the My Connections list, skip to step 12. 7. In the list, tap phone and then tap on Next. 8.
Chapter 5: Settings Connection Properties 5.40 Preliminary Draft Connection Properties This applet is used to set up serial modem connections. 182 • Tap on Start>Settings>Connections tab>Connection Properties icon • Choose a connection from the drop-down menu, and tap on Edit Properties. EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft Chapter 5: Settings Port Settings 5.40.1 Port Settings Baud Rate In the Baud rate drop-down menu, choose a new baud rate. Check your modem documentation for the appropriate baud rate. Data Bits This parameter determines the number of bits for the data going through this port. Possible values are: 4, 5, 6, 7, 8. Parity This parameter determines the type of parity checking used on the data going through the port. The options are: none, odd, even, mark and space.
Chapter 5: Settings Call Options Preliminary Draft 5.40.2 Call Options Cancel Call If Not Connected Within Tap in the checkbox to enable this option to make certain that the EP10 does not stay online too long while waiting to connect with a network. Enter the number of seconds after which the call will be cancelled. Wait For Dial Tone Before Dialing To speed connection when using a modem, disable this option – tap in the checkbox to the left of this option.
Preliminary Draft Chapter 5: Settings Modem Connection Setup 1. Tap Start>Settings, and then tap on the Connections tab. 2. Tap on the Connections icon. Note: In the Connections window, the Tasks tab is used to create new connections and manage existing ones. The Advanced tab allows you to choose a network. If you need to change these settings, contact your ISP or network administrator before making changes. 3. Under My ISP, tap on Add a new modem connection. 4.
Chapter 5: Settings Modem Connection Setup Preliminary Draft If your EP10 does not have access to a mobile phone network, insert a modem card in the unit. 1. Tap Start>Settings. Tap on the Connections tab followed by the Connections icon. 2. To create a new connection in either My ISP or My Work Network, tap on Add a new modem connection. 3. In the Make New Connection screen, type a name for the connection. 4. In the drop-down menu under Select a modem, tap on your modem type.
Preliminary Draft Chapter 5: Settings Modem Connection Setup 6. In the next screen, enter the phone number exactly as you want it dialed. If, for example, you need to dial 9 for an outside line, enter 9 at the beginning of the phone number. 7. Tap on the Next button. 8. Type the User Name, Password and Domain Name as provided by your ISP or network administrator. Note: Generally, you will not need to change any of the Advanced settings.
Chapter 5: Settings Modem Connection Setup Preliminary Draft 5.41.1.1 Advanced Modem Settings TCP/IP Settings Tab If your server assigns IP addresses dynamically, you will not need to change these settings. If you need to make changes, contact your ISP or network administrator for addresses. Server Settings Tab If your server assigns IP addresses dynamically, you will not need to change these settings. Servers requiring assigned IP addresses may also need a way to map computer names to IP addresses.
Preliminary Draft 5.42 Chapter 5: Settings Wireless Manager Icon Wireless Manager Icon The Wireless Manager icon acts as a connection manager, providing access to Wi-Fi, Bluetooth, GPS and GSM/GPRS settings. Important: The ‘Wireless Manager’ option provides detailed Help files to assist you in setting up your EP10. Help is available from the Connections tab – not from within the Wireless Manager dialog box. To access Wireless Manager help files, tap on Start>Settings>Connections tab. Tap on Start>Help.
Chapter 5: Settings Setting Up a Network Card Preliminary Draft To disable a particular radio connection rather than all connections: • Highlight an Available (enabled) radio listed in this dialog box, and then tap on the Disable button. 5.42.2 Setting Up a Network Card Network (802.11) cards are used to connect to a network so that you can browse the Internet, download e-mail and so on. You can connect to an existing network, or you can set up a new connection on your EP10.
Preliminary Draft Chapter 5: Settings Network Adaptor Cards • Tap on the Network Cards icon. • If you need to specify server information, double-tap on the appropriate adaptor, and then tap on the IP Address and/or Name Servers tab. Note: Because most networks use DHCP, you should not need to change these settings unless instructed to do so by your network administrator. • • If necessary, use a network cable to connect the network card to your network.
Chapter 5: Settings Changing Network Card Settings Preliminary Draft 5.42.4 Changing Network Card Settings • • • If you use your network card in two locations such as work and home, you’ll need to change the network to which the network card connects. Tap on Start>Settings>Connections tab>Network Cards icon. In the Configure Network Adapters dialog box, tap on the drop-down menu under My network card connects to, choose either The Internet or Work. 5.42.
Preliminary Draft • Chapter 5: Settings Managing an Existing Connection Launch a program like Internet Explorer to activate the connection. The VPN connection will start automatically. 5.42.6 Managing an Existing Connection Once you’ve defined a connection, a new option appears in the first Connections screen– Manage existing connections. 5.42.6.1 Editing a Connection • • Tap on Settings>Connections tab. Tap on the Connections icon. Tap on Manage existing connections.
Chapter 5: Settings Selecting a Network Preliminary Draft • Tap on the General tab. • • Type the name you prefer in the field labelled Enter a name for these settings. Tap on OK. 5.42.7 Selecting a Network Important: Normally, you will not need to change these settings. Contact your ISP or network administrator before making any changes. Private networks are used for work-related activities. Internet networks are used for home connection to your ISP.
Preliminary Draft • Tap on the Advanced tab. • • Tap on Select Networks. In the appropriate lists, choose My ISP or My Work Network. Chapter 5: Settings Proxy Server Setup 5.42.8 Proxy Server Setup Note: If you are connected to your ISP or private network during synchronization, the EP10 will download the appropriate settings during synchronization from your PC. If these settings are not on your PC, or if they need to be changed, you’ll need to set up the proxy server connection manually.
Chapter 5: Settings Proxy Server Setup Preliminary Draft • Under My Work Network, tap on Set up my proxy server. • Add a checkmark next to This network connects to the Internet and This network uses a proxy server to connect to the Internet. In the Proxy server field, type the proxy server name. Tap on OK to save your changes. • • Note: If you need to change advanced settings such as a port number or proxy server type, you’ll need to tap on the Advanced button rather than tapping on OK.
Preliminary Draft • • 5.43 Tap on the proxy type you want to change. For the appropriate server type, type the proxy server name and port. Tap on OK. Wireless Statistics • • 5.44 Chapter 5: Settings Wireless Statistics Tap on Start>Settings>Connections tab>Wireless Statistics icon to display the communication statistics of your wireless connection along with the radio card name, MAC address, driver version and NDIS Compliance information. Tap on the Zero button to reset the statistics.
Chapter 5: Settings Establishing a Connection Preliminary Draft A GPRS packet data connection is active. CDMA/1xRTT Signal strength is between 1% and 20%. Signal strength is between 21% and 40%. Signal strength is between 41% and 60%. Signal strength is between 61% and 80%. Signal strength is between 81% and 100%. A CDMA/1xRTT packet data connection is active. 5.44.2 Establishing a Connection • Tap on Start>Settings. Tap on the System tab followed by the Wireless WAN icon.
Preliminary Draft • • • Chapter 5: Settings Disconnecting from a Network Authenticating user User authenticated Connected Note: Keep in mind that these states may be displayed fairly quickly if the progress of the connection is rapid. When the connection state reaches PPP link to modem active, the softkey bar icon changes to indicate an active connection. The Connect Data button changes, displaying Disconnect. 5.44.
Chapter 5: Settings Advanced Information Preliminary Draft Note: If you exceed the number of allowable attempts, a PUK entry window is brought to the foreground. You’ll need to enter a new PIN number. Once the correct PIN or PUK is entered or if none was required, the modem is instructed to perform a GSM network registration followed by a GPRS attach. The main Wireless WAN dialog box reflects the progress of the initialization.
Preliminary Draft Chapter 5: Settings Tools Menu The SIM card is missing. After the SIM has been inserted a reset may be required. • SIM failure The SIM card is permanently disabled (e.g. because the wrong PUK has been entered too many times). A new SIM is needed. • Modem failure The modem did not respond to commands as expected. If a reset does not clear this condition, the modem may need to be replaced. • NDIS error An internal software error has occurred.
Chapter 5: Settings Tools Menu Preliminary Draft While automatic connection mode is enabled, the Connect Data button in the main Wireless LAN dialog box changes to Disable Auto. To close the currently active connection (if any) and disable the automatic connection mode: • Tap on Disable Auto. Important: Automatic connection mode should not be used if applications other than the Wireless WAN user interface (e.g. Connection Manager) are expected to open and close connections.
Preliminary Draft Chapter 5: Settings Tools Menu Important: For CDMA/1xRTT, automatic configuration is not available – connections must be configured manually. Under APN, the packet service access number must be entered (typically “#777”). In the following section, all the parameters that need to be configured for a connection (such as APN, user name, password, DNS server addresses etc.) are referred to as a profile. Every profile is identified by an arbitrary, unique name.
Chapter 5: Settings Tools Menu • Preliminary Draft New – Tapping on the New button allows you to create a new profile. The name of the newly created profile must be different from all existing profiles. Also, the name cannot be Default. When the New Data Profile dialog box is opened, a proposal for a unique name is filled in the corresponding entry field.
Preliminary Draft • Chapter 5: Settings Tools Menu Advanced IP – The Advanced IP button in the Show Profile and Edit Profile dialog boxes opens another dialog box that allows you to configure a static IP address as well as the IP addresses for the primary and secondary DNS and WINS resolvers. 5.44.5.2 Security Configuration The Security Configuration dialog box is called up through the Tools menu. Note: Security configuration is not available with CDMA modems.
Chapter 5: Settings Tools Menu Preliminary Draft If unauthorized access to the device is a concern, the Require PIN on resume checkbox should be checked. In this case, you will be prompted whenever a PIN is required and the PIN is not stored. 5.44.5.3 Network Configuration Note: Network configuration is not available with CDMA modems. In the main Wireless WAN screen: • Tap on the Tools menu, and choose Network.
Preliminary Draft Chapter 5: Settings Tools Menu 5.44.5.4 Driver Mode Configuration By default, the Wireless WAN driver is enabled (the Enable driver checkbox is checked). The driver must be disabled in order to access the modem directly (e.g. dial-up data, fax, or in order to manually submit AT commands to the modem for development, testing, approvals, etc.). In most cases, the Virtual WWAN serial port can be used and it is not necessary to disable the WWAN driver.
Chapter 5: Settings Tools Menu Preliminary Draft SIM, the Phone field remains empty. The modem serial number is called IMEI for GSM modems and ESN for CDMA modems. The SIM ID is sometimes referred to as the ICC ID (International Charge Card Identifier). Not all modems support the retrieval of the SIM ID. In particular, the Novatel Merlin UMTS modems and the Option Globetrotter modems do not support SIM ID retrieval.
Preliminary Draft Chapter 5: Settings SMS Menu When the EP10 enters suspend mode, the modem remains powered. If the EP10 is not turned on again during the configured time, the unit briefly wakes up from suspend mode, shuts down the modem, and enters suspend mode again. The default mode is Enabled Keep on for 1 hour. At the cost of a slightly increased power consumption in suspend mode, the modes where the modem remains powered during suspend mode have several advantages.
Chapter 5: Settings SMS Menu Preliminary Draft 5.44.6.1 New SMS Tapping on New opens a dialog box for sending a new SMS message. The recipient's phone number (to be entered in the To field) can consist of the digits 0 through 9, as well as the * and # characters, optionally preceded by one + character, indicating an international number (i.e. the country code follows immediately after the + character).
Preliminary Draft Chapter 5: Settings SMS Menu most recently received message first. The list can be sorted by any other column by clicking on the corresponding column heading. Clicking the same column heading twice reverses the sort order. Pressing any letter or digit moves the highlight to the next message whose address begins with that letter or number. Note: The date and time formats can be changed through the Regional Settings in the Control Panel.
Chapter 5: Settings SMS Menu Preliminary Draft 5.44.6.4 SMS Configuration Tapping on SMS Configuration opens the SMS configuration dialog. The SMS Centre Address follows the same rules as the recipient's phone number in the New message dialog.
Preliminary Draft 5.45 Chapter 5: Settings Windows Update Windows Update This program checks for software updates, and if found, downloads updates to your EP10. You can choose to have updates checked automatically, or if you prefer, you can determine when your unit will check for updates. EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft
Preliminary Draft 6 PERIPHERAL DEVICES & ACCESSORIES 6.1 Carrying Accessories . . . . . . . . . . . . . . . . . . . . . 6.1.1 The Hand Strap with Tether – Model No. RV6021 6.1.2 Attaching the Tether – Model No. RV6020 . . . . 6.1.3 Carrying Pouch . . . . . . . . . . . . . . . . . . . 6.2 The Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .219 .219 .221 .222 .
Preliminary Draft 6.6.5 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6.5.1 EP10 Charge Indicator LED Stays Off . . . . . . . . . . . . 6.6.5.2 EP10 Charge Indicator LED Fast Flashes Green . . . . . . . 6.6.5.3 Green LED OFF When Connected to a Network . . . . . . . 6.6.5.4 Yellow LED OFF When Connected to a 100Base-T Network 6.6.5.5 Powered Adaptor LED Stays Off . . . . . . . . . . . . . . . 6.7 Quad Charger – Model No. RV3004 . . . . . . . . . . . . . . . . . . . . . . . 6.7.
Preliminary Draft 6.12.6 Maintaining the Vehicle Cradle . . . . . . . 6.13 EA11 Imager . . . . . . . . . . . . . . . . . . . . . 6.13.1 Operating Two Dimensional (2D) Imagers . 6.14 Bluetooth Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .248 .249 .249 .250 6.15 Digital Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preliminary Draft
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Carrying Accessories 6.1 Carrying Accessories There are a variety of carrying accessories to help the operator work safely and comfortably with the EP10. Carrying Accessory Model Number Hand Straps Carrying Pouch RV6021 (with stylus and tether) - PN TBD RV6090 leather pouch (non-functional access to DC port, includes belt clip TBD model no. & functional or nonfunctional) Stylus Tether Kit RV6020 (model no.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories The Hand Strap with Tether – Model No. RV6021 Figure 6.1 Attaching The Hand Strap Hand Strap Bar Hand Strap Anchor Back of EP10 1. Attach the hand strap to the EP10 by looping the Velcro tab around the pin and adhering the tab to the Velcro pad (TBD). 2. Remove the bracket and screws from the EP10. 3. Slide the bracket through the plastic loop on the hand strap and install the screws. 4.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Attaching the Tether – Model No. RV6020 6.1.2 Attaching the Tether – Model No. RV6020 The tether can be installed to the back of the EP10 to provide a secure means for attaching the stylus to the hand-held. (TBD) Figure 6.2 Attaching the Tether Stylus BACK OF UNIT PLACE HOLDER Attaching the Velcro Retainer Attach the retainer to the EP10 by looping the Velcro tab around the pin and adhering the tab to the Velcro pad (TBD).
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Carrying Pouch Attaching the Stylus Tether to the Retainer 1. If not assembled, thread the tether cord through the stylus as shown, pulling the cord tight. 2. Thread the tether through the eyelet on the strap. 3. Pass the stylus through the tether loop and pull the tether snug. 4. Slip the stylus into the elastic holder, and you’re finished. 6.1.3 Carrying Pouch A protective carrying pouch (Model No. TBD) is available for EP10.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Adaptor Cable Options 6.3 Adaptor Cable Options The following are adaptors can be ordered for your EP10 (PN TBD): Model Number 6.4 Adaptor Cable Description CA1033 Tether to USB Host. CA1032 Tether to USB Device. (For ActiveSync) WA4010 - G1 CH1050 USB to Ethernet adaptor. Power cable used with quad docking station RV4004.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Installation: Chargers and Docking Stations • • • • • • • Do not operate the AC adaptor with a damaged cord or plug. Replace immediately. Do not disassemble the AC adaptor; it should be repaired by qualified service personnel. Incorrect reassembly may result in electric shock or fire. To reduce the risk of damage to the electric plug and cord when unplugging a docking station, pull the plug rather than the cord.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Power Consumption Considerations After unpacking your unit: • • 6.4.3 Visually inspect the charger for possible damage. Install the IEC power cord and apply power. Power Consumption Considerations Check to ensure the mains circuit supplying chargers and/or docking stations is adequate for the load, especially if several chargers and docking stations are being powered from the same circuit. • 6.5 Quad docking station can consume up to 1.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Operator Controls Figure 6.4 RV4000 Desktop Docking Station – Front View PLACE HOLDER Rear-Mounted Spare Battery Spare Battery Charge LED Stylus Important: This docking station can only be used to charge Psion Teklogix approved Lithium-Ion batteries. 6.5.1 Operator Controls The RV4000 has one operator control – the USB door on the rear that switches from Type A to Type B (see “Operating the USB Dock” on page 227). 6.5.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Operation LED. Refer to “Charging a Spare Battery” in the next section for details about LED behaviour. Note: Battery charging continues whether the EP10 is switched on or off. 6.5.3.2 Charging a Spare Battery Note: Do not store a spare battery in a charger for more than 72 hours. Doing so may damage the battery or reduce its charge capacity.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Cleaning the RV4000 Figure 6.5 RV4000 Desktop Docking Station Rear View Sliding Door Type B USB Port Type A USB Port Sliding Door DC Jack DC Jack Linking an EP10 to a PC The desktop docking station can be connected to a PC so that you can exchange files in the same way that you would between PC drives. A USB cable is included with your docking station.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Troubleshooting • • 6.5.5 Use only mild detergent or soapy water on a slightly damp cloth to clean the RV4000. Avoid abrasive cleaners, solvents or strong chemicals for cleaning. The plastic case is susceptible to harsh chemicals. It is partially soluble in oils, mineral spirits and gasoline and slowly decomposes in strong alkaline solutions. To clean ink marks from the label, use isopropyl alcohol. Troubleshooting 6.5.5.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Quad Docking Station – Model No. RV4004 • • 6.6 Disconnect and reconnect the DC adaptor, and check that the spare battery LED indicator flashes at power-up. If the charge slot fails to charge the known working battery, it is defective and requires service. Quad Docking Station – Model No. RV4004 Important: The RV4000 desktop docking station is shipped with its own user manual.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Quad Dock Operation 6.6.3 Quad Dock Operation 6.6.3.1 Charging the EP10 Battery • Insert the DC power MINI FIT JR plug into the RV4004 rear DC input receptacle. The adaptor LED should be ON when powered from the mains. The RV4004 supplies DC power to enable the EP10 internal fast charger. Normally, a full charge of the 3600 mAh EP10 battery will take from 2.5 to 3.0 hours.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Cleaning the RV4004 Figure 6.7 RV4004 Quad Docking Station Rear View PLACE HOLDER RJ45 Ethernet Port Link LED Speed LED MINI FIT JR DC Input Network Access The EP10 automatically detects insertion into the docking station and loads the appropriate drivers to communicate with the network. Network Addressing The host application uses standard TCP/IP protocol to name, locate and communicate with a specific EP10 on the network.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Troubleshooting 6.6.5 Troubleshooting 6.6.5.1 EP10 Charge Indicator LED Stays Off When an EP10 is docked into a powered RV4004 and its charge indicator LED stays off, there could be a problem with the EP10 or with the docking station. Use an EP10 with a properly functioning charge indicator to isolate the problem. 6.6.5.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Operator Controls maximum performance, it is recommended that the charger be operated at room temperature – a temperature range between 18°C to 25°C (64°F to 77°F). The charger can consume up to 6 A at 120 VAC, 3A at 240 VAC. Check to ensure the mains circuit supplying the charger is adequate for this loading (especially if several chargers are being powered from the same circuit).
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Charging Batteries Charge LED Behaviour 6.7.5 Function Flashing Yellow Battery is not charging due to out-of-temperature conditions. Solid Red Unable to read battery or non Psion Teklogix battery. Charging Batteries • Install the battery with the battery contacts facing the charger. Slide the battery between the guide rails until it lightly latches in place. The 4-LED bar for the battery bay shows 25% charger per LED.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Snap Modules • 6.8 Reconnect the mains power cable, and check that the slot indicator flashes at powerup. Snap Modules The Snap Module is a mobile power adaptor that snaps on the base of the EP10. Two types of Snap Modules are available: • USB and Charge Snap Module – Model No. RV4001. This accessory powers and charges the EP10, and it provides a USB connection. • DE9 RS232 and Charge Snap Module – Model No. RV4002.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories AC Wall Adaptor – Model No. PS1050-G1 6.9 AC Wall Adaptor – Model No. PS1050-G1 The AC wall adaptor available for your EP10 allows you to operate your EP10 using AC power while charging the battery inserted in the unit. Adaptor plugs suitable for use in the following countries are shipped with the AC wall adaptor: United Kingdom, Switzerland, Japan, Israel, Australia, Europe, and North America (see Figure 6.8 on page 237). Figure 6.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories The Non-Powered Vehicle Cradle – Model No. RV1000 Figure 6.9 Vehicle Power Outlet Adaptor Adaptor Plug Vehicle Power DC Power Plug • • 6.11 Insert the DC power plug into the DC IN port at the base of a snap module – Model No. RV4001 or RV4002 (see TBD). Insert the vehicle power outlet adaptor plug into the power outlet in your vehicle. The Non-Powered Vehicle Cradle – Model No.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Important Instructions Figure 6.10 RV1000 Vehicle Cradle Cable Tidy Restraining Mechanisms Stylus Well PLACE HOLDER Cable Pass-thru 6.11.1 Important Instructions The RV1000 storage temperature is -40°C to +70°C (-40°F to 158°F). Operating humidity and temperature is 5 - 95% non-condensing and -30°C to 60°C (-22°F to 140°F). 6.11.2 Vehicle Cradle Operation 6.11.2.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Vehicle Cradle Mounting Recommendations 6.11.2.4 Removing the EP10 from the Vehicle Cradle When removing the EP10, apply slight pressure to the rear and pull upwards. The rear-first motion will assist in disengaging the rear restraining mechanism. 6.11.3 Vehicle Cradle Mounting Recommendations Warning: Before mounting a vehicle cradle in a vehicle, there are a number of operator safety issues that require careful attention.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Vehicle Cradle Mounting Recommendations 2. Install cradles so as not to obstruct vehicle safety features, i.e. air bags, seat belts, etc. 3. Ensure cradle is secured to the vehicle in a safe location. Injury may result otherwise. 4. Ensure the mounting has the capacity to hold the cradle and the EP10. Cradle plus EP10 weight is approximately 1kg (2.2 lb.). 5. Psion Teklogix has recommended and approved mounts.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Cleaning the RV1000 Vehicle Cradle 6.11.4 Cleaning the RV1000 Vehicle Cradle Important: Dampen a soft cloth with mild detergent to wipe the unit clean. • • 6.12 Use only mild detergent or soapy water on a slightly damp cloth to clean the RV1000. Avoid abrasive cleaners, solvents or strong chemicals for cleaning. The plastic case is susceptible to harsh chemicals. The plastic is partially soluble in oils, mineral spirits and gasoline.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories The Powered Vehicle Cradle – Model No. RV1005 for the effects of the design, then we highly recommend using Psion Teklogix designed and supported accessories. If you elect to use a third party company produced cradle, Psion Teklogix cannot take responsibility for the effects of that third party product if it causes failure of our device. Important: Before using a vehicle cradle, read all instructions and markings on the housing.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories RV1005 Vehicle Cradle Mounting Recommendations 6.12.1 RV1005 Vehicle Cradle Mounting Recommendations Important: Before mounting a vehicle cradle in a vehicle, there are a number of operator safety issues that require careful attention. An improperly mounted vehicle cradle may result in one or more of the following: operator injury, operator visibility obstruction, operator distraction and/or poor ease of egress for the operator.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Cable Arrangement If you wish to custom mount the vehicle cradle to a surface other than the recommended RAM-B, please take the following precautions: • • • • When installing the cradle, ensure the driver’s view is not obstructed. Install cradles so as not to obstruct vehicle safety features, i.e. air bags, seat belts, etc. Ensure cradle is secured to the vehicle in a safe location. Injury may result otherwise.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Electrical Requirements Warning: Applying a voltage above 36VDC or reversing polarity may result in permanent damage to the vehicle cradle power section and will void the product warranty. For safety reasons, disconnect the vehicle cradle power cable when the vehicle battery is being charged by an source other than the vehicle alternator. 6.12.3.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories USB and Serial Connections • • The Powered Vehicle Cradle draws no more than 1.9 A @ 12 VDC or 0.95 A @ 24 VDC. Any additional wiring, connectors or disconnects used should be rated for at least 4A. The Powered Vehicle Cradle and peripherals can be used with both negative ground systems when using the Power Extension cable. Peripheral wiring should be closely examined to avoid ground loops in positive ground systems.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Using the Vehicle Cradle Figure 6.15 RV1005 Ports USB A (Host) Port PLACE HOLDER Serial Port B (COM 6) Serial Port A (COM 5) DC Power Port Peripherals such as scanners, printers, GPS, etc., may be used with the EP10 and the cradle. Check with Psion Teklogix if there is any compatibility issue with the device you want to use with the EP10 and the cradle. 6.12.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories EA11 Imager • • 6.13 To clean ink marks from the label, use isopropyl alcohol. The two-lock assembly in the Powered Vehicle Cradle holds the EP10 firmly in place. Although this mechanism is designed for at least 20,000 cycles, it will wear over time and will no longer lock the EP10 securely in the cradle. For replacement parts and instructions contact Psion Teklogix. Partial disassembly is required.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Bluetooth Peripherals Important: Keep in mind that the imager scanner is a camera, and the LED illumination is a flash. Glare can be an issue on reflective media such as plastic coated bar codes, just as glare is an issue for photographers. When pointing at a shiny surface, either shift the bar code to the side or top, or angle the bar code so that the glare reflects away from the imager scanner.
Preliminary Draft Chapter 6: Peripheral Devices & Accessories Digital Camera Refer to “Bluetooth Setup” on page 172 for information about setting up your Bluetooth devices for communication. In addition, review the manual shipped with your Bluetooth device to determine the method used to pair with the EP10 host. 6.15 Digital Camera The EP10 can be equipped with an optional digital camera that can take still pictures or short video clips.
Preliminary Draft
Preliminary Draft 7 SPECIFICATIONS 7.1 EP10 Specifications – Model No. 7515 . . . . . . . . . . . . . . . . . . 7.1.1 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1.2 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1.3 Wireless Communication. . . . . . . . . . . . . . . . . . . . . 7.1.4 Power Management . . . . . . . . . . . . . . . . . . . . . . . 7.1.5 Expansion Slot . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1.6 Bar Code Application . . . . . . .
Preliminary Draft
Preliminary Draft 7.1 Chapter 7: Specifications EP10 Specifications – Model No. 7515 EP10 Specifications – Model No. 7515 Note: Performance specifications are nominal and subject to change without notice. 7.1.1 Hardware Physical Dimensions • Device: 6.2" x 3.1" x 1.2" (158 mm x 78 mm x 30.6 mm) Weight (with battery pack) • Weight with battery: 0.8 lb (336 g) User Interface • Display (Backlit) - 3.7 in.
Chapter 7: Specifications Software 7.1.2 Preliminary Draft Software Platform • • • • AM3715 Processor 800 MHz (ARM Cortex A8) On-board RAM: 256 MB SDRAM On-board ROM: 2 GB Flash Operating System • Microsoft Windows Embedded 6.5 Programming Environment • • • • • HTML, XML Mobile Devices SDK JavaTM Visual Studio® 2008 Standard protocol APIs - Windows® sockets Application Software • • • • 7.1.
Preliminary Draft 7.1.4 Power Management • • • • 7.1.5 Optional High Cap 3600 mAh Li-ion rechargeable battery Full Shift operation SMART battery System backup (5 minutes) during battery swap Expansion Slot • 7.1.6 Chapter 7: Specifications Power Management One microSD slot Bar Code Application Note: User upgradeable. • 7.1.7 Digital Camera • • • • 7.1.8 3.2 mega pixel colour Auto Focus Dual LED Flash Video capture capability Voice Over IP (VOIP) • 7.1.
Chapter 7: Specifications Approvals Preliminary Draft - Desktop dock with Type A and Type B USB connectivity and charge functions for an internal battery along with a spare battery. • Power supplies: - AC wall adaptor - Vehicle power outlet adaptor - Quad charger (4-site) - Snap Module: USB DE9M powered serial plus Charger - Snap Module: USB Host/Client plus Power/Charger • Vehicle peripherals: - Powered and Non-powered cradle - RAM Mount with screws 7.1.
Preliminary Draft Chapter 7: Specifications Radio Specifications 7.2 Radio Specifications 7.2.1 Murata 802.11 a/b/g/n Direct Sequence Spread Spectrum Radio Parameter Sub-parameters Form Factor Antenna Port Antenna Type Antenna Gain Transmit Power Frequency Range Specifications Embedded surface mount module, 11.4 x 9.4 mm * This is a combo module containing both Wi-Fi 802.11a/b/g/n and Bluetooth V2.1+EDR radio 802.11b/g/n U.FL jack. Non-diversity. Multiplexed between 802.11b/g/n (2.
Preliminary Draft Chapter 7: Specifications Murata Bluetooth Radio Parameter RX Sensitivity Data Rates EVM Sub-parameters 802.11b -78 dBm @ 11 Mbps 802.11g -67 dBm @ 54 Mbps 802.11a -67 dBm @ 54 Mbps 802.11n (2.4 GHz) -66 dBm @ 65 Mbps 802.11n (5 GHz -66 dBm @ 65 Mbps 802.11b 1,2,5.5,11 Mbps 802.11a/g 6,9,12,18,24,36,48,54 Mbps 802.11n 6.5,13,19.5,26,39,52,58.5,65 Mbps 802.11b 32% max 802.11g -26 dB max 802.11a -26 dB max 802.11n (2.4 GHz) -29 dB max 802.
Preliminary Draft Parameter 7.2.3 Chapter 7: Specifications Sierra Wireless MC5728V Specifications Channel 79 RX Sensitivity -90 dBm typical, -70 dBm max Data Rates -90 dBm typical, -70 dBm max 802.11 Coexistence TI Wilink6 proprietary WiFi-BT co-existent scheme. Sierra Wireless MC5728V Features Specifications Physical • Small PCI-Express Mini Card standards-based form factor. Adheres to Rev 1.2 of the PCI Express Mini Card Specification • Two U.
Chapter 7: Specifications Sierra Wireless MC5728V Preliminary Draft Features Voice Specifications The MC5728V Mini Card has internal IS-127 and IS-733 vocoders and supports: • • • • • Packet Mode IS-95 circuit-switched Short Message Service (SMS) 262 Call origination Silent retry call origination protocol Echo cancellation E911 Incoming call notification • IS-2000 data rates up to 1531 kbps, simultaneous forward and reverse channel • IS-856 (1xEV-DO Rev. A) data rates up to 3.
Preliminary Draft 7.2.
Chapter 7: Specifications Cinterion PH8 GSM/GPRS/EDGE Radio Preliminary Draft Feature Specifications Data transfer GPRS: • Multislot Class 12 • Full PBCCH support • Mobile Station Class B • Coding Scheme 1 - 4 EGPRS: • Multislot Class 12 • EDGE E2 power class for 8 PSK • Downlink coding schemes - CS 1-4, MCS 1-9 • Uplink coding schemes - CS 1-4, MCS 1-9 • SRB loopback and test mode B • 8-bit, 11-bit RACH • PBCCH support • 1 phase/2 phase access procedures • Link adaptation and IR • NACC, extended UL TB
Preliminary Draft Chapter 7: Specifications Lithium-Ion 3600 mAh Battery Specifications Feature Specifications Audio Audio speech codecs GSM: AMR, EFR, FR, HR 3GPP: AMR Speakerphone operation, echo cancellation, noise suppression Firmware update Generic update from host application over ASC0 or USB Interfaces Module interface 80-pin board-to-board connector Antenna 50Ohms. Main GSM/UMTS antenna, UMTS diversity antenna, GPS antenna (active/passive) USB USB 2.
Preliminary Draft Chapter 7: Specifications Lithium-Ion 3600 mAh Battery Specifications Description Battery Voltage Specification 2.7 V ~ 4.2 V (minimum ~ maximum) 3.7 V (nominal) Capacity 3600 mAh/13.32Whr (typical) 3450 mAh/12.76 Whr (minimum) Charge Current 1.72 A (typical) Charge Voltage 4.2V +/- 0.05 Charge Method constant-current/constant-voltage (CC/CV) Discharge Current 1.72 A (typical) 2.
Preliminary Draft 7.4 Chapter 7: Specifications Internal Imager Internal Imager This section lists specifications for the EA11 Decoded 2D imager. 7.4.1 EA11 Decoded 2D Imager Parameter Specification Scan Rate 2D mode: 56 images/s auto adaptive Linear Emulation Mode 200 scans/s auto adaptive Scan Angle 38.9° (horizontal), 25.
Preliminary Draft 7.4.1.
Preliminary Draft APPENDIX A WIRELESS WIDE AREA NETWORK (WWAN) A.1 Wireless WAN Psion Teklogix offers the MC75i GSM/GPRS/EDGE radio – an EP10 hand-held equipped with a GSM/GPRS radio has wide area networking capabilities. With this radio and a SIM card, you can wirelessly transfer data, and you use the EP10 voice option to place phone calls. A.1.1 Taskbar Icons Wireless WAN icons in the taskbar indicate the status of your wide area network connection.
Preliminary Draft Appendix A: Wireless Wide Area Network (WWAN) Establishing a Connection The modem has found a network, and the signal strength is between 21% and 40%. The modem has found a network, and the signal strength is between 41% and 60%. The modem has found a network, and the signal strength is between 61% and 80%. The modem has found a network, and the signal strength is between 81% and 100%.
Preliminary Draft Appendix A: Wireless Wide Area Network (WWAN) Establishing a Connection Figure A.1 Establishing a Connection Note: If you are prompted to enter a PIN, refer to“Entering a PIN Number” on page A-4 for details. When “Ready to connect” is displayed in the Status field, the Connect Data button is enabled. • Tap on the Connect Data button. The progress of the connection is tracked in the Status field. • • • • PPP link to modem active. Authenticating user. User authenticated. Connected.
Preliminary Draft Appendix A: Wireless Wide Area Network (WWAN) Advanced Information When the computer’s network connection is severed, the Status field displays “Ready to connect”. The signal strength is displayed in the main Wireless WAN screen, even while a connection is active. The Rx bytes and Tx bytes fields estimate the amount of data transmitted and received, respectively. A.1.2.
Preliminary Draft Appendix A: Wireless Wide Area Network (WWAN) Advanced Information • Ready to connect. If the modem loses the connection to the GSM network, the following states are repeated: Searching for network, Registered on network, Searching for packet data, and Ready to connect. A.1.3.2 Error States The following temporary error states (i.e., these states may disappear without interaction) may be displayed: • Emergency calls only. The modem has found a network but is not allowed to register (e.
Preliminary Draft Appendix A: Wireless Wide Area Network (WWAN) Tools Menu A.1.4 Tools Menu The Tools menu in the main Wireless WAN dialog box offers some additional, advanced setup features. A.1.4.1 Data Configuration Enable Automatic Connect If the Enable automatic connect checkbox is checked (unchecked by default), the Wireless WAN user interface will attempt to establish a GPRS connection whenever GPRS is available (e.g. after resume from suspend without further user interaction).
Preliminary Draft Appendix A: Wireless Wide Area Network (WWAN) Tools Menu To activate the automatic connection mode: • Tap on the OK button. While automatic connection mode is enabled, the Connect Data button in the main Wireless LAN dialog box changes to Disable Auto. To close the currently active connection (if any) and disable the automatic connection mode: • Tap on Disable Auto. Important: Automatic connection mode should not be used if applications other than the Wireless WAN user interface (e.g.
Preliminary Draft Appendix A: Wireless Wide Area Network (WWAN) Tools Menu • A customer has subscribed for a static IP address. By definition this must be configured manually. Profiles In the following section, all the parameters that need to be configured for a connection (such as APN, user name, password, DNS server addresses etc.) are referred to as a ‘profile’. Every profile is identified by an arbitrary, unique name.
Preliminary Draft Appendix A: Wireless Wide Area Network (WWAN) Tools Menu New Tapping on the New button allows you to create a new profile. Figure A.2 Creating a New Profile The name of the newly created profile must be different from all existing profiles. Also, the name cannot be Default. When the New Data Profile dialog box is opened, a proposal for a unique name is filled in the corresponding entry field.
Preliminary Draft Appendix A: Wireless Wide Area Network (WWAN) Tools Menu Advanced IP Figure A.3 Assigning IP Information The Advanced IP button in the Show Profile and Edit Profile dialog boxes opens another dialog box that allows you to configure a static IP address as well providing DNS and WINS fields so that you can specify DNS and WINS resolvers. A.1.4.2 Security Configuration The Security Configuration dialog box is accessed through the Tools menu.
Preliminary Draft Appendix A: Wireless Wide Area Network (WWAN) Tools Menu used without further user interaction whenever the modem requires a PIN (such as resume after suspend or modem removal). The stored PIN is also automatically entered in the Current PIN text box whenever the Security Configuration dialog box is called up. If unauthorized access to the device is a concern, the Require PIN on resume checkbox should be checked.
Preliminary Draft Appendix A: Wireless Wide Area Network (WWAN) Tools Menu Note: Your home network operator will need to let you know which other networks have roaming agreements. Even when a network is listed with an ‘Available’ status, it does not necessarily follow that it can be used or that the roaming agreement covers GPRS. A status of ‘Forbidden’ indicates that the network cannot be used.
Preliminary Draft Appendix A: Wireless Wide Area Network (WWAN) Tools Menu Bluetooth. An external modem connected to a serial port must support 115.2kbit/s, 8bit, no parity and hardware flow control. A.1.4.5 Modem Information The fields in this dialog box cannot be edited, they only display information about the computer’s modem. If the network operator has not programmed a user’s phone number into his SIM, the Phone: field remains empty.
Preliminary Draft Appendix A: Wireless Wide Area Network (WWAN) Tools Menu Taskbar Choosing Taskbar displays a dialog box in which you can determine which Wireless WAN icons will be displayed in the taskbar. Sounds Tapping on the Sounds option displays a dialog box in which you can customize which sounds your EP10 will emit and when these sounds will be played. A-14 EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft Appendix A: Wireless Wide Area Network (WWAN) SMS Menu A.1.5 SMS Menu SMS (Short Message Service) functions are accessed through the SMS menu. For modems that support a SIM card, the SIM initialization typically takes longer than the network initialization, resulting in a noticeable delay before the SMS functions become available. A.1.5.1 New Tapping on the New button opens a dialog for sending a new SMS message.
Preliminary Draft Appendix A: Wireless Wide Area Network (WWAN) Voice Note: The date and time formats can be changed through the Region and Language menu in Control Panel. For a new date or time format to take effect the Inbox has to be closed and re-opened. The Open button opens the selected message in a new window such that the entire message can be read including the original formatting (line breaks are replaced by spaces in the Inbox message list).
Preliminary Draft Appendix A: Wireless Wide Area Network (WWAN) Power Mode A.2 Power Mode The power mode of the modem is controlled through the Power menu in the Control Panel (not through the Wireless WAN user interface). For CF Card modems, the settings are found under the Devices tab. If the checkbox for a modem is unchecked, no power is applied to the modem and no driver is loaded (neither the serial port driver nor the Wireless WAN driver).
Preliminary Draft
Preliminary Draft APPENDIX B PORT PINOUTS B.1 Dock Port Pinout Pin # Pin Name Signal Direction Relative To DPA DGND - VDD_EXT_PWR Input VDD_BATT_OUT Output Comment 1 GND 2 VDD_EXT_PWR 3 VDD_EXT_PWR 4 VDD_EXT_PWR 5 BATT_OUT 6 AUDIO_P Output Audio positive. 7 AUDIO_N Output Audio negative. 8 VDD_USBOTG Bi-directional USB Power (+5.5V). As output, supplies external devices when EP10 is in USB Host mode. As input, charges battery when EP10 is in USB Client mode.
Preliminary Draft Appendix B: Port Pinouts Battery Contact Pinout Pin # B.2 Pin Name Direction Relative To DPA Comment 12 USB_OTG_ID 13 GND 14 TXDATA Output RS-232 data transmit. Max bit rate 115 kbits/sec. 15 RXDATA Input RS-232 data receive. Max bit rate 115 kbits/sec.
Preliminary Draft APPENDIX C BAR CODES SETTINGS C.1 Scanner Menu The drop down menu to the right of the Scanner option allows you to choose from the imager for your unit. The symbologies listed change to reflect the scanner you choose and the bar codes it supports. Important: To improve the decode speed and performance, enable only those codes that are required by the application. Keep in mind that some bar code types are only available when an internal imaging scanner is installed.
Appendix C: Bar Codes Settings Decoded (Internal) Scanner Preliminary Draft C.2 Decoded (Internal) Scanner C.2.1 Options – Decoded (Internal) Scanner Dot Time (msec) The value selected for “Dot Time (msec)” determines (in milliseconds) how long the targeting dot remains on before the scanner switches to a normal scan sweep. When you doubletap on this parameter, a dialog box is displayed in which you can enter a value of 0 msec, 200 msec or 400 msec. A value of 0 (zero) disables the target dot.
Preliminary Draft C.2.2 Appendix C: Bar Codes Settings Advanced Options – Decoded (Internal) Advanced Options – Decoded (Internal) Continuous Scan Mode Setting this parameter to ‘on’ keeps the laser on and continuously decoding as long as the scanner button is pressed and held down. Minimum Cancel Time The value assigned to this parameter determines the time delay before the scanner is turned off, once the scanner trigger or button is released.
Appendix C: Bar Codes Settings Advanced Options – Decoded (Internal) Preliminary Draft Linear Security Level This parameter allows you to select the security level appropriate for your bar code quality. There are four levels of decode security for linear code types (e.g., Code 39, Interleaved 2 of 5). Higher security levels should be selected for decreasing levels of bar code quality. As security levels increase, the scanner’s decode speed decreases.
Preliminary Draft Appendix C: Bar Codes Settings Decoded (Internal) 2D Scanning Options When this parameter is enabled, a bar code must be successfully scanned in both directions (forward and reverse) before being decoded. Scan Angle This option allows you to choose from two scan angles: Normal Angle or Alternate Angle. Choosing Normal Angle allows the normal operation for scanning long range and short range.
Appendix C: Bar Codes Settings Code 39 Preliminary Draft Scan Data Format This parameter allows you to change the scan data transmission format. Double-tapping on “Scan Data Format” displays the following options from which you can choose a data format: data (as-is), data [S1], data [S2], data [S1][S2], [P] data, [P] data [S1], [P] data [S2] and [P] data [S1][S2]. Prefix [P], Suffix [S1] And Suffix [S2] A prefix and/or one or two suffixes may be appended to scan data for use in data editing.
Preliminary Draft Appendix C: Bar Codes Settings Code 39 Convert To Code 32 Note: “Code 39” must be enabled in order for this parameter to function. Setting this parameter to on allows the scanner to convert the bar code from “Code 39” to “Code 32”. Code 32 Prefix Note: “Convert to Code 32” must be enabled in order for this parameter to function. When this parameter is enabled, the prefix character “A” is added to all “Code 32” bar codes.
Appendix C: Bar Codes Settings Code 39 Preliminary Draft Check Digit Verification When this parameter is enabled (set to on), the integrity of a “Code 39” symbol is checked to ensure that it complies with specified algorithms. Note: Only those “Code 39” symbols that include a Mod 43 check digit are decoded when this parameter is enabled. Transmit Check Digit If the check digit is to be transmitted with the data, this parameter must to enabled.
Preliminary Draft Appendix C: Bar Codes Settings Code 128 Field Size When a value is assigned for this parameter, only bar codes that match the field size exactly can be transmitted. If a value is assigned to this parameter, a Minimum Size and Maximum Size value is not required. Minimum Size And Maximum Size When a value is assigned to these parameters, only bar code lengths that fall between the minimum and maximum value can be decoded.
Appendix C: Bar Codes Settings EAN 13 Preliminary Draft Enable ISBT 128 To successfully scan this variation, “Enable ISBT 128” must be set to on. Decode Performance If this parameter is set to on, one of three decode levels assigned to the “Decode Performance Level” parameter can be selected. Decode Perf. Level This parameter provides three levels of decode performance or “aggressiveness” for Code 128 symbols.
Preliminary Draft Appendix C: Bar Codes Settings UPC A Add/Remove Data Refer to “Add/Remove Data” on page C-9 for details. C.2.9 UPC A Enabled Set this parameter to on to enable “UPC A”. UPC-A Check Digit If you enable this parameter, the check digit is included with the decoded bar code data.
Appendix C: Bar Codes Settings UPC/EAN Shared Settings Preliminary Draft transmitted with the data or None – no preamble is transmitted. The lead-in characters are considered part of the symbol. Conv. UPC-E To UPC-A This parameter converts UPC-E (zero suppressed) decoded data to UPC-A format before transmission. After conversion, data follows UPC-A format and is affected by UPC-A programming selections (e.g., Preamble, Check Digit). Conv.
Preliminary Draft Appendix C: Bar Codes Settings Code 93 Security Level This parameter controls the tolerance for decoding edge-to-edge UPC/EAN bar codes. Double-tapping on this parameter displays a dialog box in which you can choose a level from 0 to 3. Lower values have a lower tolerance for misreads, but they also increase the time it takes to decode the bar code. Linear Decode “Linear Decode” applies to code types containing two adjacent blocks (e.g., UPC-A, EAN8, EAN-13).
Appendix C: Bar Codes Settings Codabar C.2.13 Preliminary Draft Codabar Enabled Set this parameter to on to enable “Codabar” or off to disable it. Set Length L1 And Set Length L2 Lengths for “Codabar” can be set for Any length, Length within a range, One discrete length or Two discrete lengths. The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s).
Preliminary Draft Appendix C: Bar Codes Settings MSI Plessey Set Length L1 And Set Length L2 Lengths for “MSI Plessey” can be set for Any length, Length within a range, One discrete length or Two discrete lengths. The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s). Double-tapping on this parameter displays a dialog box labelled Set Code Lengths where you can define the code length that will be recognized by your scanner.
Appendix C: Bar Codes Settings Interleaved 2 of 5 C.2.15 Preliminary Draft Interleaved 2 of 5 Enabled Set this parameter to on to enable “Interleaved 2 of 5”. Set Length L1 And Set Length L2 Lengths for “Interleaved 2 of 5” can be set for Any length, Length within a range, One discrete length or Two discrete lengths. The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s).
Preliminary Draft Appendix C: Bar Codes Settings RSS Code Set Length L1 And Set Length L2 Lengths for “Discrete 2 of 5” can be set for Any length, Length within a range, One discrete length or Two discrete lengths. The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s). Double-tapping on this parameter displays a dialog box labelled Set Code Lengths where you can define the code length that will be recognized by your scanner.
Appendix C: Bar Codes Settings Composite Preliminary Draft Length Restriction Refer to “Length Restriction” on page C-8 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-9 for details. C.2.18 Composite Important: To successfully read this type of bar code, the two types of symbologies included in a composite bar code must be enabled. In addition, “Center Bar Code Only” must be disabled.
Preliminary Draft C.2.20 Appendix C: Bar Codes Settings Micro PDF-417 Micro PDF-417 Enable Setting this parameter to on enables “Micro PDF-417” bar code scanning. Micro PDF-417 is a multi-row symbology that is useful for applications requiring greater area efficiency but lower data capacity than PDF-417. Code 128 Emulation When this parameter is enabled, the scanner transmits data from certain Micro PDF-417 symbols as if it was encoded in Code 128 symbols.
Appendix C: Bar Codes Settings Decoded C.3 Decoded • C.3.1 Preliminary Draft Tap on the Scanner drop down menu, and choose Decoded (Intermec ISCP). Options – Decoded Scanner Laser On Time The value assigned to this parameter determines how long the laser will remain on when the scan button or trigger is pressed. Double-tapping on this parameter displays a dialog box in which you can enter a value between 1 and 10 seconds. C.3.
Preliminary Draft Appendix C: Bar Codes Settings Code 39 Low Power Timeout To extend laser life, you can select the length of time the scanner remains active following a successful decode. The scanner wakes from low power mode when a bar code is scanned – a successful decode restores normal blinking. When you double-tap on this parameter, a dialog box is displayed in which you can choose a value of 30 sec, 1 min, 2 min or 3 min.
Appendix C: Bar Codes Settings Code 39 Preliminary Draft Full ASCII If this parameter is enabled, the characters +, %, and / are used as escape characters. The combination of an escape character and the next character is converted to an equivalent ASCII character. Reading Range Determines the reading distance from which a bar code can be successfully scanned. The default setting, Extended, allows for increased reading distance.
Preliminary Draft Appendix C: Bar Codes Settings Code 128 Add/Remove Data Refer to “Add/Remove Data” on page C-9 for details. C.3.4 Code 128 Enable Setting this parameter to on enables “Code 128”. GS1-128 “GS1-128” is the GS1 implementation of the Code 128 barcode specification. The former correct name was UCC/EAN-128. GS1-128 Identifier “GS1-128 Identifier” allows the AIM ID " ]C1" for EAN 128 to be transmitted or removed. By default, this identifier is transmitted if EAN 128 is enabled.
Appendix C: Bar Codes Settings EAN 13 Preliminary Draft Single transmits single codes or concatenated codes. If only one code of a pair is read, that code will be transmitted as a single code. If both codes in a pair are detected, they will be concatenated provided that ISBT Concat Any Pair (see below) is enabled. ISBT Concat Any Pair Enabling this parameter causes all code pairs that can be, to be concatenated even if they do not comply with Section 4.
Preliminary Draft Appendix C: Bar Codes Settings EAN 8 Transmit Check Digit If the check digit is to be transmitted with the data, this parameter must be enabled. Add/Remove Data Refer to “Add/Remove Data” on page C-9 for details. C.3.6 EAN 8 Enabled Set this parameter to on to enable “EAN 8”. Transmit Check Digit If the check digit is to be transmitted with the data, this parameter must be enabled. Convert To EAN 13 If this parameter is enabled, an EAN 8 bar code is converted to EAN 13.
Appendix C: Bar Codes Settings UPC E C.3.8 Preliminary Draft UPC E Enabled Set this parameter to on to enable “UPC E”. Enable UPC-E1 Set this parameter to on to allow “UPC-E1” (zero suppressed) bar code scans. Transmit Check Digit If the check digit is to be transmitted with the data, this parameter must be enabled. Transmit Number System If this parameter is enabled, the number system digit is transmitted with the decoded bar code data.
Preliminary Draft Appendix C: Bar Codes Settings Code 93 Addendum Add-on 2 And Addendum Add-on 5 Enabling these parameters sets the length of the addendum bar code to either 2 or 5 characters. Addendum Security If you tap on “Addendum Security”, a dialog box is displayed in which you can define the security level of add-on 2 or add-on 5 with a value from 0 to 100. As security levels increase, the scanner decode speed decreases.
Appendix C: Bar Codes Settings Codabar C.3.11 Preliminary Draft Codabar Enabled Set this parameter to on to enable “Codabar”. Start/Stop Transmit Codabar can use the following sets of characters as start and stop characters: a, b, c, d A, B, C, D a, b, c, d, /, t, n, *, e DC1, DC2, DC3, DC4 Thus, when a set is chosen, the first and last digits of a Codabar message must be one of those characters and the body of the message should not contain these characters.
Preliminary Draft Appendix C: Bar Codes Settings MSI Plessey Length Restriction Refer to “Length Restriction” on page C-8 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-9 for details. C.3.12 MSI Plessey Enabled Set this parameter to on to enable “MSI”. Enable Plessy Set this parameter to on to enable “Plessy”. Check Digit Verification The available options for this parameter are MOD 10 Check and Double MOD 10 Check.
Appendix C: Bar Codes Settings Code 11 C.3.13 Preliminary Draft Code 11 Enabled Set this parameter to on to enable “Code 11”. Check Digit Verification The available options for this parameter are MOD 10 Check and Double MOD 10 Check.This parameter uses the specified algorithm of the option you've chosen to ensure the integrity of the symbol data before transmitting. If the data does not contain that algorithm, the data is not transmitted.
Preliminary Draft Appendix C: Bar Codes Settings Matrix 2 of 5 Note: French CIP (French pharmaceutical) is only used with bar codes containing 7 characters. Transmit Check Digit If the check digit is to be transmitted with the data, this parameter must be enabled. Set Length L1, Set Length L2, And Set Length L3 Lengths for “Interleaved 2 of 5” can be set from 0 to 255. The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s).
Appendix C: Bar Codes Settings Discrete 2 of 5 C.3.16 Preliminary Draft Discrete 2 of 5 Enabled Set this parameter to on to enable “Discrete 2 of 5”. Standard 2 of 5 Format This parameter allows you to choose a standard format – either Identic on (6 start/stop bars) or Computer Identics (4 start/stop bars). Check Digit Verification The available options for this parameter are Disabled and MOD 10 Check.
Preliminary Draft Appendix C: Bar Codes Settings RSS Code (Reduced Space Symbology) Format This parameter allows you to set the bar code character format to either ASCII or Numeric. Minimum Length Minimum lengths for the bar code can be set from 0 to 255. The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s). Length Restriction Refer to “Length Restriction” on page C-8 for details.
Appendix C: Bar Codes Settings Composite Preliminary Draft Add/Remove Data Refer to “Add/Remove Data” on page C-9 for details. C.3.19 Composite Important: To successfully read this type of bar code, the two types of symbologies included in a composite bar code must be enabled. In addition, “Center Bar Code Only” must be disabled. A composite symbol includes multi-row 2D components making it compatible with linear and area CCD scanners along with linear and rastering laser scanners.
Preliminary Draft Appendix C: Bar Codes Settings PDF-417 Security Level This parameter is used to differentiate between TLC-39 and standard Code 39. Tapping on “Security Level” displays a dialog box in which you can assign a value from 0 to 100. The higher the value assigned, the lower the decode rate. Length Restriction Refer to “Length Restriction” on page C-8 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-9 for details. C.3.
Appendix C: Bar Codes Settings Codablock Preliminary Draft ]L3 - if the first codeword is 903-907, 912, 914, 915 ]L4 - if the first codeword is 908 or 909 ]L5 - if the first codeword is 910 or 911 Length Restriction Refer to “Length Restriction” on page C-8 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-9 for details. C.3.23 Codablock Enable Codablock A Set this parameter to on to enable “Codablock type A”. Enable Codablock F Set this parameter to on to enable “Codablock type F”.
Preliminary Draft C.4 Imager • C.4.1 Appendix C: Bar Codes Settings Imager Tap on the Scanner drop down menu, and choose Imager. Options – Imager Center Barcode Only Note: This parameter must be disabled when reading Composite bar codes. When more than one bar code is visible in a single snap shot, this parameter allows you to specify that only the centre image within the imager framing marker be read.
Appendix C: Bar Codes Settings Code 39 Settings C.4.2 Preliminary Draft Code 39 Settings Enabled Set this parameter to on to enable “Code 39”. Full ASCII If this parameter is enabled, the characters +, %, and / are used as escape characters. The combination of an escape character and the next character is converted to an equivalent ASCII character.
Preliminary Draft Appendix C: Bar Codes Settings EAN 8 Addendum An addendum is a separate bar code, supplementary to the main bar code. This parameter provides three options: Disabled, Optional and Required. Depending on the value chosen for this parameter, an addendum is recognized or ignored. • Double-tap on Addendum to display a dialog box listing your options. • Highlight an item, and tap on OK. When “Addendum” is set to Disabled, the scanner does not recognize an addendum.
Appendix C: Bar Codes Settings UPC E C.4.7 Preliminary Draft UPC E Enabled Set this parameter to on to enable “UPC E”. Addendum Refer to “Addendum” on page C-26. Add/Remove Data Refer to “Add/Remove Data” on page C-9 for details. C.4.8 Code 93 Enabled Set this parameter to on to enable “Code 93”. Length Restriction Refer to “Length Restriction” on page C-8 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-9 for details. C.4.
Preliminary Draft Appendix C: Bar Codes Settings RSS Code (Reduced Space Symbology) Check Digit Verification When enabled, this parameter checks the integrity of an I 2 of 5 symbol to ensure it complies with a specified algorithm – either USS (Uniform Symbology Specification) or OPCC (Optical Product Code Council). Include Check If this parameter is enabled, the check digit is transmitted along with the I 2 of 5 symbol. Length Restriction Refer to “Length Restriction” on page C-8 for details.
Appendix C: Bar Codes Settings Micro PDF-417 Preliminary Draft Length Restriction Refer to “Length Restriction” on page C-8 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-9 for details. C.4.14 Micro PDF-417 Enable Setting this parameter to on enables “Micro PDF-417” bar code scanning. Micro PDF-417 is a multi-row symbology that is useful for applications requiring greater area efficiency but lower data capacity than PDF-417.
Preliminary Draft Appendix C: Bar Codes Settings 2D QR Code Length Restriction Refer to “Length Restriction” on page C-8 for details. Add/Remove Data Refer to “Add/Remove Data” on page C-9 for details. C.4.16 2D QR Code Enabled Set this parameter to on to enable “2D QR Code”. Field Size Refer to “Field Size” on page C-9 for details. C.4.17 2D Maxicode Enabled Set this parameter to on to read “2D Maxicode” images. Length Restriction Refer to “Length Restriction” on page 8 for details.
Appendix C: Bar Codes Settings Postal: PlaNET C.4.19 Preliminary Draft Postal: PlaNET Enabled Set this parameter to on to enable “Postal: PlaNET”. Length Restriction Refer to “Length Restriction” on page 8 for details. Add/Remove Data Refer to “Add/Remove Data” on page 9 for details. C.4.20 Postal: PostNET Enabled Set this parameter to on to enable “Postal: PostNET”. Length Restriction Refer to “Length Restriction” on page 8 for details. Add/Remove Data Refer to “Add/Remove Data” on page 9 for details.
Preliminary Draft Appendix C: Bar Codes Settings Postal: Korean Length Restriction Refer to “Length Restriction” on page 8 for details. Add/Remove Data Refer to “Add/Remove Data” on page 9 for details. C.4.23 Postal: Korean Enabled Set this parameter to on to enable “Postal: Korean”. Length Restriction Refer to “Length Restriction” on page 8 for details. Add/Remove Data Refer to “Add/Remove Data” on page 9 for details. C.4.24 Postal: Royal Enabled Set this parameter to on to enable “Postal: Royal”.
Appendix C: Bar Codes Settings Postal: Canadian C.4.26 Preliminary Draft Postal: Canadian Enabled Set this parameter to on to enable “Postal: Canadian”. Length Restriction Refer to “Length Restriction” on page 8 for details. Add/Remove Data Refer to “Add/Remove Data” on page 9 for details. C-46 EP10 Hand-Held (Windows Embedded 6.
Preliminary Draft APPENDIX D TEKLOGIX IMAGERS APPLET The Teklogix Imagers applet is used to create, modify, delete and activate imager settings. The principle uses of the applet are to decode bar codes and to capture images. A Demonstration Application is provided to demonstrates how the imager works. Refer to “PTSI Imager Demo” on page 69 for details. D.
Appendix D: Teklogix Imagers Applet Predefined Presets Preliminary Draft Every preset belongs to a preset type. The following preset types are available: • Imaging for photo capture. • Imaging for bar code decoding. • Symbology selection. At any time, only one preset of each type can be designated as the user-selected active preset. D.2.1 Predefined Presets Predefined presets are built into the imaging software and cannot be changed.
Preliminary Draft Appendix D: Teklogix Imagers Applet Bar Code Decoding Camera Predefined Presets Linear This preset enables the decoding of all the 1D symbologies that the imager can decode. See “Imager” on page C-37 for a description of these symbologies. Linear and PDF417 This preset enables the decoding of all the 1D and PDF symbologies that the imager can decode. See “Imager” on page C-37 for a description of these symbologies.
Appendix D: Teklogix Imagers Applet Image Capture Predefined Presets D.2.4 Preliminary Draft Image Capture Predefined Presets The following presets enable successful image capture in almost all conditions. Note: It is recommended that the default preset be used whenever possible. Default This preset works in a wide range of conditions. It is optimized for a normal office lighting (about 300 Lux). Motion This preset uses a shorter exposure time so as to freeze motion.
Preliminary Draft Appendix D: Teklogix Imagers Applet Selecting A Camera The following screen is displayed: Figure D.4 Imaging Tab This window lists all the presets, both predefined and custom. Presets are identified as follows: • • • D.3.2 Predefined presets are marked as read-only. Custom presets are marked as read and write. One preset – either predefined or custom – is marked as active.
Appendix D: Teklogix Imagers Applet Viewing A Preset D.3.4 Preliminary Draft Viewing A Preset To view the parameter settings in a preset: • Highlight a preset, and tap on the View button. The associated preset window is displayed. • D.3.5 Tap on the + sign to expand the lists so that you can view the parameter settings. Creating A Custom Preset A new custom preset is created by modifying a preset – either a predefined preset or an existing custom preset.
Preliminary Draft Appendix D: Teklogix Imagers Applet Modifying A Custom Preset In this example, the Low light near preset was chosen. A screen like the sample below is displayed. • Type the name of the new preset in the dialog box. • Tap on OK to save your changes. The preset list is displayed; the new custom preset appears at the end of the list. It is marked as read and write. D.3.6 Modifying A Custom Preset The parameter values in a custom preset can be modified.
Appendix D: Teklogix Imagers Applet Modifying A Custom Preset Preliminary Draft • Highlight the custom preset, and tap on the Edit button. • • • Tap on the + symbols to expand the lists so that you can view the parameter settings. Scroll through the parameter list until you reach the parameter that you want to change. For a parameter that can take a range of values: - Highlight the parameter, and then press the [SPACE] key or double-click the parameter.
Preliminary Draft Appendix D: Teklogix Imagers Applet Removing A Custom Preset - Highlight the parameter and then press the [SPACE] key, or double-click on the parameter. Either method toggles between the two available values. • When you’ve completed your edits, tap on OK. The parameter list is displayed; the new value for the changed parameter is shown. • D.3.7 Tap on OK to exit to the preset list and save the changes.
Appendix D: Teklogix Imagers Applet Selecting A Camera Preliminary Draft Note: The top portion of the window displays the bar code decoding camera presets. The top port of the window displays the bar code decoding camera presets. D.4.1 Selecting A Camera If your EP10 has more than one built-in camera, one camera must be selected for configuration. To select a camera: • • Tap on the Camera Presets dropdown menu to view the camera options.
Preliminary Draft Appendix D: Teklogix Imagers Applet Creating A Custom Preset The associated preset window is displayed. • D.4.4 Tap on the + sign to expand one of the lists so that you can view the parameter settings. Creating A Custom Preset A new custom preset is created by modifying a preset – either a predefined preset or an existing custom preset. To create a custom preset: • Highlight a preset, and tap on the Add button. A screen like the sample following is displayed.
Appendix D: Teklogix Imagers Applet Modifying A Custom Preset Preliminary Draft The preset list is displayed; the new custom preset appears at the end of the list. It is marked as read and write. D.4.5 Modifying A Custom Preset The parameter values in a custom preset can be modified. It is recommended that very few changes be made to a custom preset. To ensure that it will work reliably, it should be as close as possible to the original predefined preset.
Preliminary Draft Appendix D: Teklogix Imagers Applet Removing A Custom Preset - Highlight the parameter, and then press the [SPACE] key or double-click the parameter. - An associated dialog box containing the valid range of values for the parameter and the current setting like the sample screen following is displayed. - Type a value in the field provided.
Appendix D: Teklogix Imagers Applet Setting The Active Preset Preliminary Draft Figure D.6 Viewing Bar Code Decoding Symbologies D.4.8 Setting The Active Preset An active preset has an A to the right; in Figure D.5 on page page D-9, the active preset is Defaults. To set an active preset: • D.4.9 Highlight the preset, and tap on the Activate button. Viewing A Preset To view the parameter settings in a preset: • Highlight a preset, and tap on the View button. The associated preset window is displayed.
Preliminary Draft • Appendix D: Teklogix Imagers Applet Creating A Custom Preset Tap on the + sign to expand one of the lists so that you can view the parameter settings. D.4.10 Creating A Custom Preset A new custom preset is created by modifying a preset – either a predefined preset or an existing custom preset. To create a custom preset: • Highlight a preset, and tap on the Add button. A screen like the sample following is displayed. • Type the name of the new preset in the dialog box.
Appendix D: Teklogix Imagers Applet Modifying A Custom Preset Preliminary Draft D.4.11 Modifying A Custom Preset The parameter values in a custom preset can be modified. It is recommended that very few changes be made to a custom preset. To ensure that it will work reliably, it should be as close as possible to the original predefined preset. To change a parameter value: D-16 • Highlight the custom preset, and tap on the Edit button.
Preliminary Draft Appendix D: Teklogix Imagers Applet Removing A Custom Preset - An associated dialog box containing the valid range of values for the parameter and the current setting like the sample screen following is displayed. - Type a value in the field provided. • For a parameter that toggles between two values such as on or off and enabled or disabled: - Highlight the parameter and then press the [SPACE] key, or double-click on the parameter.
Appendix D: Teklogix Imagers Applet Filter Tab – Manipulating Bar Code Data Preliminary Draft Configuring Symbologies In The Teklogix Scanners Applet When a symbology is enabled or configured using the Teklogix Scanners applet, the changes are also made in the My Default preset. My Default automatically becomes the active bar code symbology preset. None of the other bar code decoding predefined presets is changed.
Preliminary Draft • • Appendix D: Teklogix Imagers Applet Filter Tab – Manipulating Bar Code Data Scroll through the parameter list until you reach the parameter that you want to change. For a parameter that can take a range of values: - Highlight the parameter, and then press the [SPACE] key or double-click the parameter. - An associated dialog box containing the valid range of values for the parameter and the current setting like the sample screen following is displayed.
Appendix D: Teklogix Imagers Applet Translation Tab – Configuring Rules Preliminary Draft D.4.15 Translation Tab – Configuring Rules Translation rules enable the automatic processing of bar code data. Up to 10 cases can be defined, each consisting of up to 10 sequential rules. Note: Changes made to the translations configuration using the Teklogix Scanner Control Panel program are synchronized with changes made here. Changes made in either place affect both translation tables.
Preliminary Draft Appendix D: Teklogix Imagers Applet Advanced Tab • Tap on the File Location button. • • • Type the file Name, choose the Folder and file Type. Choose the Location in which your files will be saved. When you have completed all the changes, tap on the Save button. D.4.16.2 Configuring Triggers Viewing The Trigger Configuration The trigger on the EP10 hand-held is configured using the Manage Triggers applet. The Teklogix Imagers applet provides a shortcut to the Manage Triggers applet.
Appendix D: Teklogix Imagers Applet Teklogix Scanners Applet • Preliminary Draft To view all the triggers and the hardware devices that are configured to use them, tap in the checkbox next to Show all modules. Adding, Editing And Removing Triggers For instruction about adding, editing and removing triggers, refer to “Manage Triggers” on page 133. D.5 Teklogix Scanners Applet The bar code symbologies that are to be read by the imager can be enabled using the Teklogix Scanners applet.
Preliminary Draft INDEX Numbers 2DAztec D-43 2D Data Matrix D-42 2D imager scanner 249 2D Maxicode D-43 2D QR Code D-43 2D Raster Expand Rate D-5 2D UPC Half Block Stitching D-13 802.11a/b/g/n radio specifications 259 802.
Index Preliminary Draft Code 11 D-30 Code 128 D-9, D-38 Code 39 D-38 Code 93 D-13, D-27, D-40 Discrete 2 of 5 D-16, D-32 EAN 13 D-10, D-24, D-38 EAN 8 D-10, D-25, D-39 Interleaved 2 of 5 D-16, D-30, D-40 Matrix 2 of 5 D-31 MSI Plessey D-14, D-29 UPC A D-11, D-25, D-39 UPC E D-11, D-26, D-40 Translation tab 154 bar code reader applications 267 integrated scanner, operation of 249 internal or integrated 267 Barcodes Must Decode D-37 batteries a description of 222 Battery Details tab 140 battery hotkey 34 Bat
Preliminary Draft Check Digit, One D-15 Check Digits (MSI Plessey) D-15 Check Digit Verification D-8, D-22, D-24, D-29, D-30, D-32 Check Digit Verification (Codabar) D-28 Check Digit Verification (Code 39) D-38 Check Digit Verification (I 2 of 5) D-16, D-41 cleaning EP10 26 Click Data (scanner double-click) 152 Click Time (scanner double-click) 152 clock, setting 34, 124 CLSI Editing D-14 CLSI Library System D-28 Codabar D-14, D-28, D-40 Codabar D-14 Codablock D-36 Code 11 D-30 Code 128 D-38 Code 128 D-9, D
Preliminary Draft Index Dial-String Commands (modem setup) 184 Dial Tone, wait for (modem setup) 184 Diff Read Timeout D-21 digit check digit D-15 digital camera description 251 digital camera specifications 257 Discrete 2 of 5 D-16, D-32 Discrete 2 of 5 D-16 display backlight, adjusting 19 docking port B-1 docking station RV4000, desktop operator controls 226 RV4004, quad operator controls 230, 231, 233 uploading data using 24 docking stations 223 desktop docking station 225 installation at site 224 quad
Preliminary Draft GSM/GPRS 197–208, B-1–B-17 GSM/GPRS/EDGE radio specifications 263 GTIN Compliant D-23, D-27 H hand strap 219 hand strap (RV6021), attaching 219 hardware, description of 120 headsets, pairing (Bluetooth) 25, 175 Help 51 hotkeys (navigation bar) 170 I Identifier Default preset group C-2 Imager D-37 imager (2D) scanner scanning 2D 249 imager options 249 Imager Settings 149 Include Check (I 2 of 5) D-41 indicators LED functions 21 scanner message 250 softkey bar 47 inking settings 110 Input
Preliminary Draft Index Maximum Size D-9 Minimum Size D-9 Letter Recognizer 55 Letter Recognizer options (Input Methods tab) 109 Linear Predefined preset C-3 Linear and PDF Predefined preset C-3 Linear Decode D-13 Linear Security Level D-4 Linear Transmission only (Decoded Composite) D-34 Linear Transmission only (TLC-39) D-34 Lock Sequence 106 Low light Predefined preset C-3 Low light near Predefined preset C-4 Low power Predefined preset C-3 Low Power Timeout D-3, D-21 M Macro keys 19 deleting a macro
Preliminary Draft renaming 74 synchronizing 75 text, converting handwriting into 72 Notes 71 Notification, setting 117 NOTIS Editing D-14 O One Check Digit D-15 One Shot Mode 99 One Shot tab (modifier keys) 99 onscreen (soft) keyboard 52 Options tab (bar codes) 152 orientation, screen 21 Outlook e-mail, synchronizing (Messaging) 84 Owner Information 115 ownership information, defining 36 P pairing Bluetooth devices 175 Parameter Scanning D-3, D-21, D-22, D-23, D-24, D-27, D-29, D-30, D-31, D-33 Parity 159
Preliminary Draft Index Default identifier C-2 profile, creating backup 161 profile, restoring backup 164 Programs 49, 59 minimizing 49 opening 49 properties, EP10 120 protective case 222 proxy server, setting up 195 Q quad docking station (RV4004) 230 R radio 802.11a/b/g /n Direct Sequence SS 259 802.
Preliminary Draft Decoded Intermec (ISCP) D-20 Decode Perf.
Preliminary Draft Index softkey (softkey bar) 47 softkey bar shift-state indicator 48 softkey 47 soft keyboard icon 48 softkeys 47 soft keyboard (onscreen) 52 soft keyboard icon (softkey bar) 48 softkeys (softkey bar) 47 Soft Scan Timeout 153 software specifications 256 Sound, setting events 117 Sound settings 116 specifications 802.
Preliminary Draft Transmit Check Digit (MSI Plessey) D-15 Transmit Code 1D Char D-5 Transmit Number System D-25, D-26 trigger mappings 134 Trigger On Sequence 159 Trigger Press Type, Manage Triggers menu 136 Trioptic Code 39, Enable D-6 troubleshooting RV40004 233 RV4000 LED 229 TweakIT 164 Index warnings 153 Windows Mobile 6.
Preliminary Draft
