User's Manual
Table Of Contents
- Introduction 1
- Basic Checkout 2
- 2.2 Preparing The 7545 For Operation
- 2.3 Powering Up The 7545
- 2.5 Calibrating The Touchscreen
- 2.6 Configuring Your Radio
- 2.7 Configuring An IEEE 802.11 Radio In The Unit
- 2.8 Summit Client Utility (SCU) For 802.11b/g Radio
- 2.9 Checking The Scanner
- 2.10 Data Transfer Between The 7545 And A PC
- 2.11 Resetting The 7545
- Getting To Know Your 7545 3
- Windows Embedded CE 5.0 4
- Configuration 5
- 5.1 Remote Connect
- 5.2 The TekTerm Application
- 5.3 Pocket PC Compatibility
- 5.4 The Control Panel
- 5.5 Control Panel Icons
- 5.6 Control Panel Applications: Basic Setup
- 5.7 Bluetooth Setup
- 5.8 Error Reporting
- 5.9 IPv6 Support
- 5.10 Scanner Settings
- 5.11 SNMP (Simple Network Management Protocol) Setup
- 5.12 The Storage Manager
- 5.13 Teklogix Error Handling Service
- 5.14 Teklogix Imagers
- 5.15 Total Recall
- 5.16 TweakIT Settings
- Specifications 7
- Appendix B
- SCU For 802.11b/g Radio
- B.1.2.1 SCU Security Capabilities
- B.1.2.2 SCU EAP Types
- B.1.2.3 EAP Credentials
- B.1.2.4 ThirdPartyConfig
- Appendix C
- Bar Code Settings
- C.1 Bar Code Settings
- C.2 Decoded (Internal) Scanners
- C.2.1 Options
- C.2.2 Decoded (Internal) Advanced Options
- C.2.3 Decoded (Internal) 2D Scanning Options
- C.2.4 Decoded (Internal) Data Options
- C.2.5 Code 39
- C.2.6 Code 128
- C.2.7 EAN 13
- C.2.8 EAN 8
- C.2.9 UPC A
- C.2.10 UPC E
- C.2.11 UPC/EAN Shared Settings
- C.2.12 Code 93
- C.2.13 Codabar
- C.2.14 MSI Plessey
- C.2.15 Interleaved 2 of 5
- C.2.16 Discrete 2 of 5
- C.2.17 RSS Code (Reduced Space Symbology)
- C.2.18 Composite
- C.2.19 PDF-417
- C.2.20 Micro PDF-417
- C.3 Decoded (Intermec ISCP)
- C.3.1 Decoded (ISCP) Options
- C.3.2 Decoded (ISCP) Advanced Options
- C.3.3 Code 39
- C.3.4 Code 128
- C.3.5 EAN 13
- C.3.6 EAN 8
- C.3.7 UPC A
- C.3.8 UPC E Settings
- C.3.9 UPC/EAN Shared Settings
- C.3.10 Code 93
- C.3.11 Codabar
- C.3.12 MSI Plessey
- C.3.13 Code 11
- C.3.14 Interleaved 2 of 5
- C.3.15 Matrix 2 of 5
- C.3.16 Discrete 2 of 5
- C.3.17 Telepen
- C.3.18 RSS Code (Reduced Space Symbology)
- C.3.19 Composite
- C.3.20 TLC-39
- C.3.21 PDF-417
- C.3.22 Micro PDF-417
- C.3.23 Codablock
- C.4 Imager
- C.4.1 Imager Options
- C.4.2 Imager Advanced Options
- C.4.3 Code 39
- C.4.4 Code 128
- C.4.5 EAN 13
- C.4.6 EAN 8
- C.4.7 UPC A
- C.4.8 UPC E
- C.4.9 Code 93
- C.4.10 Codabar
- C.4.11 Interleaved 2 of 5
- C.4.12 RSS Code (Reduced Space Symbology)
- C.4.13 Composite
- C.4.14 PDF-417
- C.4.15 Micro PDF-417
- C.4.16 2D Data Matrix
- C.4.17 2D QR Code
- C.4.18 2D Maxicode
- C.4.19 2D Aztec
- C.4.20 Postal: PlaNET
- C.4.21 Postal: PostNET
- C.4.22 Postal: Australian
- C.4.23 Postal: Japanese
- C.4.24 Postal: Korean
- C.4.25 Postal: Royal
- C.4.26 Postal: Kix
- C.4.27 Postal: Canadian
- C.5 Non-Decoded Scanners
Chapter 5: Configuration
Keyboard Properties
108 Psion Teklogix 7545 Hand-Held Computer User Manual
5.6.5.5 Unicode Mapping
•In the Keyboard Properties dialog box, open the Unicode Mapping tab.
The Unicode Mapping tab is used to map combinations of virtual key values and [CTRL]
and [SHIFT] states to Unicode™ values. This tab shows the configured Unicode character
along with the Unicode value. For example, the sample screen above shows “a (U+0061)”
indicating that the character “a” is represented by the Unicode value “0061”, and so on.
Keep in mind that Unicode configurations are represented as hexadecimal rather than
decimal values.
All user-defined Unicode mappings are listed in the Unicode Mapping tab in order of virtual
key value, and then by order of the shift state. If a Unicode mapping is not listed, the
Unicode mapping is mapped to the default Unicode value.
Adding And Changing Unicode Values
Important: Changes to Unicode mappings are not saved until you exit the Keyboard
Properties dialog box.
Preliminary Draft 3