User's Manual
Table Of Contents
- Introduction 1
- Basic Checkout 2
- 2.2 Preparing The 7545 For Operation
- 2.3 Powering Up The 7545
- 2.5 Calibrating The Touchscreen
- 2.6 Configuring Your Radio
- 2.7 Configuring An IEEE 802.11 Radio In The Unit
- 2.8 Summit Client Utility (SCU) For 802.11b/g Radio
- 2.9 Checking The Scanner
- 2.10 Data Transfer Between The 7545 And A PC
- 2.11 Resetting The 7545
- Getting To Know Your 7545 3
- Windows Embedded CE 5.0 4
- Configuration 5
- 5.1 Remote Connect
- 5.2 The TekTerm Application
- 5.3 Pocket PC Compatibility
- 5.4 The Control Panel
- 5.5 Control Panel Icons
- 5.6 Control Panel Applications: Basic Setup
- 5.7 Bluetooth Setup
- 5.8 Error Reporting
- 5.9 IPv6 Support
- 5.10 Scanner Settings
- 5.11 SNMP (Simple Network Management Protocol) Setup
- 5.12 The Storage Manager
- 5.13 Teklogix Error Handling Service
- 5.14 Teklogix Imagers
- 5.15 Total Recall
- 5.16 TweakIT Settings
- Specifications 7
- Appendix B
- SCU For 802.11b/g Radio
- B.1.2.1 SCU Security Capabilities
- B.1.2.2 SCU EAP Types
- B.1.2.3 EAP Credentials
- B.1.2.4 ThirdPartyConfig
- Appendix C
- Bar Code Settings
- C.1 Bar Code Settings
- C.2 Decoded (Internal) Scanners
- C.2.1 Options
- C.2.2 Decoded (Internal) Advanced Options
- C.2.3 Decoded (Internal) 2D Scanning Options
- C.2.4 Decoded (Internal) Data Options
- C.2.5 Code 39
- C.2.6 Code 128
- C.2.7 EAN 13
- C.2.8 EAN 8
- C.2.9 UPC A
- C.2.10 UPC E
- C.2.11 UPC/EAN Shared Settings
- C.2.12 Code 93
- C.2.13 Codabar
- C.2.14 MSI Plessey
- C.2.15 Interleaved 2 of 5
- C.2.16 Discrete 2 of 5
- C.2.17 RSS Code (Reduced Space Symbology)
- C.2.18 Composite
- C.2.19 PDF-417
- C.2.20 Micro PDF-417
- C.3 Decoded (Intermec ISCP)
- C.3.1 Decoded (ISCP) Options
- C.3.2 Decoded (ISCP) Advanced Options
- C.3.3 Code 39
- C.3.4 Code 128
- C.3.5 EAN 13
- C.3.6 EAN 8
- C.3.7 UPC A
- C.3.8 UPC E Settings
- C.3.9 UPC/EAN Shared Settings
- C.3.10 Code 93
- C.3.11 Codabar
- C.3.12 MSI Plessey
- C.3.13 Code 11
- C.3.14 Interleaved 2 of 5
- C.3.15 Matrix 2 of 5
- C.3.16 Discrete 2 of 5
- C.3.17 Telepen
- C.3.18 RSS Code (Reduced Space Symbology)
- C.3.19 Composite
- C.3.20 TLC-39
- C.3.21 PDF-417
- C.3.22 Micro PDF-417
- C.3.23 Codablock
- C.4 Imager
- C.4.1 Imager Options
- C.4.2 Imager Advanced Options
- C.4.3 Code 39
- C.4.4 Code 128
- C.4.5 EAN 13
- C.4.6 EAN 8
- C.4.7 UPC A
- C.4.8 UPC E
- C.4.9 Code 93
- C.4.10 Codabar
- C.4.11 Interleaved 2 of 5
- C.4.12 RSS Code (Reduced Space Symbology)
- C.4.13 Composite
- C.4.14 PDF-417
- C.4.15 Micro PDF-417
- C.4.16 2D Data Matrix
- C.4.17 2D QR Code
- C.4.18 2D Maxicode
- C.4.19 2D Aztec
- C.4.20 Postal: PlaNET
- C.4.21 Postal: PostNET
- C.4.22 Postal: Australian
- C.4.23 Postal: Japanese
- C.4.24 Postal: Korean
- C.4.25 Postal: Royal
- C.4.26 Postal: Kix
- C.4.27 Postal: Canadian
- C.5 Non-Decoded Scanners
Chapter 5: Configuration
Manage Triggers
Psion Teklogix 7545 Hand-Held Computer User Manual 115
Show All Modules
By default, the trigger mapping list only shows active mappings. Mappings for drivers or
applications that are not currently active are not normally displayed. By checking this
checkbox, all mappings, both active and inactive, are displayed.
Add
Tapping this button brings up the Add Mapping dialog (see page 115), so that you can add
new trigger mappings.
Edit
Tapping this button brings up the Edit Mapping dialog (see page 115), so that you can edit
existing trigger mappings.
Remove
Tapping this button removes an existing mapping.
OK
The OK button in the top right of the Manage Triggers screen saves all changes made. If the
cancel button X is tapped instead, or the [ESC] key is pressed, all changes made will
be discarded.
5.6.6.2 Add And Edit Trigger Mapping
These dialogs allow you to add and edit trigger mappings.
Preliminary Draft 3