User's Manual
Table Of Contents
- Introduction 1
- Basic Checkout 2
- 2.2 Preparing The 7545 For Operation
- 2.3 Powering Up The 7545
- 2.5 Calibrating The Touchscreen
- 2.6 Configuring Your Radio
- 2.7 Configuring An IEEE 802.11 Radio In The Unit
- 2.8 Summit Client Utility (SCU) For 802.11b/g Radio
- 2.9 Checking The Scanner
- 2.10 Data Transfer Between The 7545 And A PC
- 2.11 Resetting The 7545
- Getting To Know Your 7545 3
- Windows Embedded CE 5.0 4
- Configuration 5
- 5.1 Remote Connect
- 5.2 The TekTerm Application
- 5.3 Pocket PC Compatibility
- 5.4 The Control Panel
- 5.5 Control Panel Icons
- 5.6 Control Panel Applications: Basic Setup
- 5.7 Bluetooth Setup
- 5.8 Error Reporting
- 5.9 IPv6 Support
- 5.10 Scanner Settings
- 5.11 SNMP (Simple Network Management Protocol) Setup
- 5.12 The Storage Manager
- 5.13 Teklogix Error Handling Service
- 5.14 Teklogix Imagers
- 5.15 Total Recall
- 5.16 TweakIT Settings
- Specifications 7
- Appendix B
- SCU For 802.11b/g Radio
- B.1.2.1 SCU Security Capabilities
- B.1.2.2 SCU EAP Types
- B.1.2.3 EAP Credentials
- B.1.2.4 ThirdPartyConfig
- Appendix C
- Bar Code Settings
- C.1 Bar Code Settings
- C.2 Decoded (Internal) Scanners
- C.2.1 Options
- C.2.2 Decoded (Internal) Advanced Options
- C.2.3 Decoded (Internal) 2D Scanning Options
- C.2.4 Decoded (Internal) Data Options
- C.2.5 Code 39
- C.2.6 Code 128
- C.2.7 EAN 13
- C.2.8 EAN 8
- C.2.9 UPC A
- C.2.10 UPC E
- C.2.11 UPC/EAN Shared Settings
- C.2.12 Code 93
- C.2.13 Codabar
- C.2.14 MSI Plessey
- C.2.15 Interleaved 2 of 5
- C.2.16 Discrete 2 of 5
- C.2.17 RSS Code (Reduced Space Symbology)
- C.2.18 Composite
- C.2.19 PDF-417
- C.2.20 Micro PDF-417
- C.3 Decoded (Intermec ISCP)
- C.3.1 Decoded (ISCP) Options
- C.3.2 Decoded (ISCP) Advanced Options
- C.3.3 Code 39
- C.3.4 Code 128
- C.3.5 EAN 13
- C.3.6 EAN 8
- C.3.7 UPC A
- C.3.8 UPC E Settings
- C.3.9 UPC/EAN Shared Settings
- C.3.10 Code 93
- C.3.11 Codabar
- C.3.12 MSI Plessey
- C.3.13 Code 11
- C.3.14 Interleaved 2 of 5
- C.3.15 Matrix 2 of 5
- C.3.16 Discrete 2 of 5
- C.3.17 Telepen
- C.3.18 RSS Code (Reduced Space Symbology)
- C.3.19 Composite
- C.3.20 TLC-39
- C.3.21 PDF-417
- C.3.22 Micro PDF-417
- C.3.23 Codablock
- C.4 Imager
- C.4.1 Imager Options
- C.4.2 Imager Advanced Options
- C.4.3 Code 39
- C.4.4 Code 128
- C.4.5 EAN 13
- C.4.6 EAN 8
- C.4.7 UPC A
- C.4.8 UPC E
- C.4.9 Code 93
- C.4.10 Codabar
- C.4.11 Interleaved 2 of 5
- C.4.12 RSS Code (Reduced Space Symbology)
- C.4.13 Composite
- C.4.14 PDF-417
- C.4.15 Micro PDF-417
- C.4.16 2D Data Matrix
- C.4.17 2D QR Code
- C.4.18 2D Maxicode
- C.4.19 2D Aztec
- C.4.20 Postal: PlaNET
- C.4.21 Postal: PostNET
- C.4.22 Postal: Australian
- C.4.23 Postal: Japanese
- C.4.24 Postal: Korean
- C.4.25 Postal: Royal
- C.4.26 Postal: Kix
- C.4.27 Postal: Canadian
- C.5 Non-Decoded Scanners
Chapter 5: Configuration
Trap Destination
Psion Teklogix 7545 Hand-Held Computer User Manual 151
• Highlight the community you want to remove in the Communities tab and then choose
the Remove button.
A Delete Confirmation screen is displayed.
• To remove a community, choose the Yes button, or
If you decide not to remove the community, choose the No button.
5.11.3 Trap Destination
A trap is an unsolicited report sent to SNMP Managers by the SNMP Agent running on the
managed node. This option allows you to define where the report will be sent.
5.11.3.1 Enabling Authentication TRAPS
Enabling Enable Authentication TRAPS allows authorization traps to be sent when a failure
is detected (e.g., an SNMP message received with a bad community name).
5.11.3.2 Adding A Destination
To add a new destination:
Preliminary Draft 3