User's Manual
Table Of Contents
- Introduction 1
- Basic Checkout 2
- 2.2 Preparing The 7545 For Operation
- 2.3 Powering Up The 7545
- 2.5 Calibrating The Touchscreen
- 2.6 Configuring Your Radio
- 2.7 Configuring An IEEE 802.11 Radio In The Unit
- 2.8 Summit Client Utility (SCU) For 802.11b/g Radio
- 2.9 Checking The Scanner
- 2.10 Data Transfer Between The 7545 And A PC
- 2.11 Resetting The 7545
- Getting To Know Your 7545 3
- Windows Embedded CE 5.0 4
- Configuration 5
- 5.1 Remote Connect
- 5.2 The TekTerm Application
- 5.3 Pocket PC Compatibility
- 5.4 The Control Panel
- 5.5 Control Panel Icons
- 5.6 Control Panel Applications: Basic Setup
- 5.7 Bluetooth Setup
- 5.8 Error Reporting
- 5.9 IPv6 Support
- 5.10 Scanner Settings
- 5.11 SNMP (Simple Network Management Protocol) Setup
- 5.12 The Storage Manager
- 5.13 Teklogix Error Handling Service
- 5.14 Teklogix Imagers
- 5.15 Total Recall
- 5.16 TweakIT Settings
- Specifications 7
- Appendix B
- SCU For 802.11b/g Radio
- B.1.2.1 SCU Security Capabilities
- B.1.2.2 SCU EAP Types
- B.1.2.3 EAP Credentials
- B.1.2.4 ThirdPartyConfig
- Appendix C
- Bar Code Settings
- C.1 Bar Code Settings
- C.2 Decoded (Internal) Scanners
- C.2.1 Options
- C.2.2 Decoded (Internal) Advanced Options
- C.2.3 Decoded (Internal) 2D Scanning Options
- C.2.4 Decoded (Internal) Data Options
- C.2.5 Code 39
- C.2.6 Code 128
- C.2.7 EAN 13
- C.2.8 EAN 8
- C.2.9 UPC A
- C.2.10 UPC E
- C.2.11 UPC/EAN Shared Settings
- C.2.12 Code 93
- C.2.13 Codabar
- C.2.14 MSI Plessey
- C.2.15 Interleaved 2 of 5
- C.2.16 Discrete 2 of 5
- C.2.17 RSS Code (Reduced Space Symbology)
- C.2.18 Composite
- C.2.19 PDF-417
- C.2.20 Micro PDF-417
- C.3 Decoded (Intermec ISCP)
- C.3.1 Decoded (ISCP) Options
- C.3.2 Decoded (ISCP) Advanced Options
- C.3.3 Code 39
- C.3.4 Code 128
- C.3.5 EAN 13
- C.3.6 EAN 8
- C.3.7 UPC A
- C.3.8 UPC E Settings
- C.3.9 UPC/EAN Shared Settings
- C.3.10 Code 93
- C.3.11 Codabar
- C.3.12 MSI Plessey
- C.3.13 Code 11
- C.3.14 Interleaved 2 of 5
- C.3.15 Matrix 2 of 5
- C.3.16 Discrete 2 of 5
- C.3.17 Telepen
- C.3.18 RSS Code (Reduced Space Symbology)
- C.3.19 Composite
- C.3.20 TLC-39
- C.3.21 PDF-417
- C.3.22 Micro PDF-417
- C.3.23 Codablock
- C.4 Imager
- C.4.1 Imager Options
- C.4.2 Imager Advanced Options
- C.4.3 Code 39
- C.4.4 Code 128
- C.4.5 EAN 13
- C.4.6 EAN 8
- C.4.7 UPC A
- C.4.8 UPC E
- C.4.9 Code 93
- C.4.10 Codabar
- C.4.11 Interleaved 2 of 5
- C.4.12 RSS Code (Reduced Space Symbology)
- C.4.13 Composite
- C.4.14 PDF-417
- C.4.15 Micro PDF-417
- C.4.16 2D Data Matrix
- C.4.17 2D QR Code
- C.4.18 2D Maxicode
- C.4.19 2D Aztec
- C.4.20 Postal: PlaNET
- C.4.21 Postal: PostNET
- C.4.22 Postal: Australian
- C.4.23 Postal: Japanese
- C.4.24 Postal: Korean
- C.4.25 Postal: Royal
- C.4.26 Postal: Kix
- C.4.27 Postal: Canadian
- C.5 Non-Decoded Scanners
B-8 Psion Teklogix 7545 Hand-Held Computer User Manual
Appendix B: SCU For 802.11b/g Radio
Profile
• If the credentials are not specified in the profile, when the radio tries to associate using
that profile, you will be prompted to enter the credentials.
• When prompted, you can enter valid credentials, enter invalid credentials, or cancel
the operation.
- If you enter valid credentials and tap OK, the radio will associate and authenticate.
- If you enter invalid credentials and tap on OK, the radio will associate but will not
authenticate; you will be prompted again to enter credentials.
- If you tap on Cancel or clear the credentials fields and tap on OK, the radio will not
attempt to associate with that profile until you perform one of the following actions
(while the profile is the active profile):
- Cause the 7545 to go through a power cycle or suspend/resume.
- Disable and enable the radio, or tap the Reconnect button on the Diags windows.
- Modify the Profile, and tap on Commit.
Alternatively, you can choose another profile as the active profile and then switch back to
the profile for which EAP authentication was cancelled.
B.1.2.4 ThirdPartyConfig
If you choose to configure ThirdPartyConfig, the SCU will work with the operating sys-
tem’s Windows Zero Config (WZC) to configure radio and security settings for the CF radio
installed in the unit.
Choosing this profile means that WZC must be used to define the following radio and secu-
rity options: SSID, Auth Type, EAP Type, and Encryption.The SCU settings for
ThirdPartyConfig include: Client Name, Power Save, Tx Power, Bit Rate, and Radio Mode.
These SCU settings along with SCU global settings and the WZC settings will be applied to
the radio module.
Preliminary Draft 3