User's Manual
Table Of Contents
- Introduction 1
- Basic Checkout 2
- 2.2 Preparing The 7545 For Operation
- 2.3 Powering Up The 7545
- 2.5 Calibrating The Touchscreen
- 2.6 Configuring Your Radio
- 2.7 Configuring An IEEE 802.11 Radio In The Unit
- 2.8 Summit Client Utility (SCU) For 802.11b/g Radio
- 2.9 Checking The Scanner
- 2.10 Data Transfer Between The 7545 And A PC
- 2.11 Resetting The 7545
- Getting To Know Your 7545 3
- Windows Embedded CE 5.0 4
- Configuration 5
- 5.1 Remote Connect
- 5.2 The TekTerm Application
- 5.3 Pocket PC Compatibility
- 5.4 The Control Panel
- 5.5 Control Panel Icons
- 5.6 Control Panel Applications: Basic Setup
- 5.7 Bluetooth Setup
- 5.8 Error Reporting
- 5.9 IPv6 Support
- 5.10 Scanner Settings
- 5.11 SNMP (Simple Network Management Protocol) Setup
- 5.12 The Storage Manager
- 5.13 Teklogix Error Handling Service
- 5.14 Teklogix Imagers
- 5.15 Total Recall
- 5.16 TweakIT Settings
- Specifications 7
- Appendix B
- SCU For 802.11b/g Radio
- B.1.2.1 SCU Security Capabilities
- B.1.2.2 SCU EAP Types
- B.1.2.3 EAP Credentials
- B.1.2.4 ThirdPartyConfig
- Appendix C
- Bar Code Settings
- C.1 Bar Code Settings
- C.2 Decoded (Internal) Scanners
- C.2.1 Options
- C.2.2 Decoded (Internal) Advanced Options
- C.2.3 Decoded (Internal) 2D Scanning Options
- C.2.4 Decoded (Internal) Data Options
- C.2.5 Code 39
- C.2.6 Code 128
- C.2.7 EAN 13
- C.2.8 EAN 8
- C.2.9 UPC A
- C.2.10 UPC E
- C.2.11 UPC/EAN Shared Settings
- C.2.12 Code 93
- C.2.13 Codabar
- C.2.14 MSI Plessey
- C.2.15 Interleaved 2 of 5
- C.2.16 Discrete 2 of 5
- C.2.17 RSS Code (Reduced Space Symbology)
- C.2.18 Composite
- C.2.19 PDF-417
- C.2.20 Micro PDF-417
- C.3 Decoded (Intermec ISCP)
- C.3.1 Decoded (ISCP) Options
- C.3.2 Decoded (ISCP) Advanced Options
- C.3.3 Code 39
- C.3.4 Code 128
- C.3.5 EAN 13
- C.3.6 EAN 8
- C.3.7 UPC A
- C.3.8 UPC E Settings
- C.3.9 UPC/EAN Shared Settings
- C.3.10 Code 93
- C.3.11 Codabar
- C.3.12 MSI Plessey
- C.3.13 Code 11
- C.3.14 Interleaved 2 of 5
- C.3.15 Matrix 2 of 5
- C.3.16 Discrete 2 of 5
- C.3.17 Telepen
- C.3.18 RSS Code (Reduced Space Symbology)
- C.3.19 Composite
- C.3.20 TLC-39
- C.3.21 PDF-417
- C.3.22 Micro PDF-417
- C.3.23 Codablock
- C.4 Imager
- C.4.1 Imager Options
- C.4.2 Imager Advanced Options
- C.4.3 Code 39
- C.4.4 Code 128
- C.4.5 EAN 13
- C.4.6 EAN 8
- C.4.7 UPC A
- C.4.8 UPC E
- C.4.9 Code 93
- C.4.10 Codabar
- C.4.11 Interleaved 2 of 5
- C.4.12 RSS Code (Reduced Space Symbology)
- C.4.13 Composite
- C.4.14 PDF-417
- C.4.15 Micro PDF-417
- C.4.16 2D Data Matrix
- C.4.17 2D QR Code
- C.4.18 2D Maxicode
- C.4.19 2D Aztec
- C.4.20 Postal: PlaNET
- C.4.21 Postal: PostNET
- C.4.22 Postal: Australian
- C.4.23 Postal: Japanese
- C.4.24 Postal: Korean
- C.4.25 Postal: Royal
- C.4.26 Postal: Kix
- C.4.27 Postal: Canadian
- C.5 Non-Decoded Scanners
C-10 Psion Teklogix 7545 Hand-Held Computer User Manual
Appendix C: Bar Code Settings
Decoded (Internal) Scanners
Decoded (Internal) 2D Scanning Options
Linear security level 3 specifies that code types other than the following must be success-
fully read twice before being decoded. The following codes must be read three times:
Linear security level 4 requires that all code types be successfully read three times before
being decoded.
Bi-Direction Redundancy
When this parameter is enabled, a bar code must be successfully scanned in both directions
(forward and reverse) before being decoded.
Scan Angle
This option allows you to choose from two scan angles: Normal Angle or Alternate Angle.
Choosing Normal Angle allows the normal operation for scanning long range and short
range. Choosing Alternate Angle widens the beam to allow scanning of long bar codes at
short range but at the cost of long range scanning.
C.2.3 Decoded (Internal) 2D Scanning Options
Scanning Mode
When you double-tap on this parameter, a dialog box is displayed in which you can choose
one of the following scanning modes: Smart Raster, Always Raster, Programmable Raster,
Slab Pattern, Cyclone Pattern, or Semi-Omni Pattern.
Raster Height And Raster Expand Rate
These parameters determine the laser pattern’s height and rate of expansion.
Code Type Length
MSI Plessey 4 or less
D 2 of 5 8 or less
I 2 of 5 8 or less
Note: This parameter is only valid if a” Linear Security Level” is enabled.
Note: These parameters are only used when either Programmable Raster or
Always Raster is assigned to the “2D Scanning Mode” parameter. “2D Raster
Height” and “2D Raster Expand Rate” are intended for very specific applications
and are usually not required for normal scanning purposes.
Preliminary Draft 3