User's Manual
Table Of Contents
- Appendix A
- Appendix B
- Appendix C
- Bar Code Settings - TBD
- C.2 Decoded (Internal) Scanners
- C.2.1 Options
- C.2.2 Decoded (Internal) Advanced Options
- C.2.3 Decoded (Internal) Data Options
- C.2.4 Code 39
- C.2.5 Code 128
- C.2.6 EAN 13
- C.2.7 EAN 8
- C.2.8 UPC A
- C.2.9 UPC E
- C.2.10 UPC/EAN Shared Settings
- C.2.11 Code 93
- C.2.12 Codabar
- C.2.13 MSI Plessey
- C.2.14 Interleaved 2 of 5
- C.2.15 Discrete 2 of 5
- C.2.16 RSS Code (Reduced Space Symbology)
- C.2.17 Composite
- C.2.18 PDF-417
- C.2.19 Micro PDF-417
- C.3 Decoded (HHP)
- C.4 Decoded (Intermec ISCP)
- C.4.1 Decoded (ISCP) Options
- C.4.2 Decoded (ISCP) Advanced Options
- C.4.3 Code 39
- C.4.4 Code 128
- C.4.5 EAN 13
- C.4.6 EAN 8
- C.4.7 UPC A
- C.4.8 UPC E Settings
- C.4.9 UPC/EAN Shared Settings
- C.4.10 Code 93
- C.4.11 Codabar
- C.4.12 MSI Plessey
- C.4.13 Code 11
- C.4.14 Interleaved 2 of 5
- C.4.15 Matrix 2 of 5
- C.4.16 Discrete 2 of 5
- C.4.17 Telepen
- C.4.18 RSS Code (Reduced Space Symbology)
- C.4.19 Composite
- C.4.20 TLC-39
- C.4.21 PDF-417
- C.4.22 Micro PDF-417
- C.4.23 Codablock
- C.5 Non-Decoded Scanners
- Appendix D
- Teklogix Imagers Applet
- D.1 Required Applets
- D.2 Presets
- D.3 Using the Teklogix Imagers Applet
- D.3.1 Configuring the Image Capture Presets (Imaging Tab)
- D.3.2 Configuring the Bar Code Decoding Camera Presets (Barcoding Tab)
- D.3.3 Configuring the Bar Code Decoding Symbologies (Barcoding Tab)
- D.3.4 Barcoding Tab – Configuring Symbologies
- D.3.5 Filter Tab – Manipulating Bar Code Data
- D.3.6 Translation Tab – Configuring Rules
- D.3.7 Advanced Tab
- D.4 Bar Code Symbologies – Descriptions
- D.4.1 Options
- D.4.2 All 1D With Strong Recovery Enabled
- D.4.3 Code 39
- D.4.4 Code 128
- D.4.5 EAN 13
- D.4.6 EAN 8
- D.4.7 UPC-A
- D.4.8 UPC-E
- D.4.9 Code 93
- D.4.10 Codabar
- D.4.11 Interleaved 2 of 5
- D.4.12 GS1 DataBar
- D.4.13 2D PDF-417
- D.4.14 2D Micro PDF-417
- D.4.15 2D Data Matrix
- D.4.16 2D QR Code
- D.4.17 2D Maxicode
- D.4.18 2D Aztec
- D.4.19 Postal: PlaNET
- D.4.20 Postal: PostNET
- D.4.21 Postal: Australian
- D.4.22 Postal: Canadian
- D.4.23 Postal: Japanese
- D.4.24 Postal: Kix
- D.4.25 Postal: Korean
- D.4.26 Postal: Royal
D-24 Psion Teklogix Omnii Hand-Held Computer User Manual
Appendix D: Teklogix Imagers Applet
Code 128
Full ASCII Enabled
If this parameter is enabled, the characters +, %, and / are used as escape characters. The
combination of an escape character and the next character is converted to an equivalent
ASCII character.
Check Char
When this parameter is enabled, before data is output, the “Code 39” symbol integrity is ver-
ified based on a parity character that must be present in the code. If the parity character is not
part of the code, the code is not output. Keep in mind the parity character may not be part of
your output setup; in this case, this parameter should be turned off.
Check Char Strip
If this parameter is set to on, check characters – if present – are not output.
D.4.4 Code 128
Enabled
Set this parameter to on to enable “Code 128”.
D.4.5 EAN 13
Enabled
Set this parameter to on to enable “EAN 13”.
Supplements 2 and Supplements 5
Supplements are additions to EAN/UPC codes. These addendums can be 2 or 5 characters in
length. Usually, data from an addendum is a suffix to the main symbol output data.
Mandatory Enabled
When this parameter is set to on, the imager does not accept the main bar code without a
supplement.
D.4.6 EAN 8
Enabled
Set this parameter to on to enable “EAN 8”.
Draft 1