User's Manual
Table Of Contents
- Appendix A
- Appendix B
- Appendix C
- Bar Code Settings - TBD
- C.2 Decoded (Internal) Scanners
- C.2.1 Options
- C.2.2 Decoded (Internal) Advanced Options
- C.2.3 Decoded (Internal) Data Options
- C.2.4 Code 39
- C.2.5 Code 128
- C.2.6 EAN 13
- C.2.7 EAN 8
- C.2.8 UPC A
- C.2.9 UPC E
- C.2.10 UPC/EAN Shared Settings
- C.2.11 Code 93
- C.2.12 Codabar
- C.2.13 MSI Plessey
- C.2.14 Interleaved 2 of 5
- C.2.15 Discrete 2 of 5
- C.2.16 RSS Code (Reduced Space Symbology)
- C.2.17 Composite
- C.2.18 PDF-417
- C.2.19 Micro PDF-417
- C.3 Decoded (HHP)
- C.4 Decoded (Intermec ISCP)
- C.4.1 Decoded (ISCP) Options
- C.4.2 Decoded (ISCP) Advanced Options
- C.4.3 Code 39
- C.4.4 Code 128
- C.4.5 EAN 13
- C.4.6 EAN 8
- C.4.7 UPC A
- C.4.8 UPC E Settings
- C.4.9 UPC/EAN Shared Settings
- C.4.10 Code 93
- C.4.11 Codabar
- C.4.12 MSI Plessey
- C.4.13 Code 11
- C.4.14 Interleaved 2 of 5
- C.4.15 Matrix 2 of 5
- C.4.16 Discrete 2 of 5
- C.4.17 Telepen
- C.4.18 RSS Code (Reduced Space Symbology)
- C.4.19 Composite
- C.4.20 TLC-39
- C.4.21 PDF-417
- C.4.22 Micro PDF-417
- C.4.23 Codablock
- C.5 Non-Decoded Scanners
- Appendix D
- Teklogix Imagers Applet
- D.1 Required Applets
- D.2 Presets
- D.3 Using the Teklogix Imagers Applet
- D.3.1 Configuring the Image Capture Presets (Imaging Tab)
- D.3.2 Configuring the Bar Code Decoding Camera Presets (Barcoding Tab)
- D.3.3 Configuring the Bar Code Decoding Symbologies (Barcoding Tab)
- D.3.4 Barcoding Tab – Configuring Symbologies
- D.3.5 Filter Tab – Manipulating Bar Code Data
- D.3.6 Translation Tab – Configuring Rules
- D.3.7 Advanced Tab
- D.4 Bar Code Symbologies – Descriptions
- D.4.1 Options
- D.4.2 All 1D With Strong Recovery Enabled
- D.4.3 Code 39
- D.4.4 Code 128
- D.4.5 EAN 13
- D.4.6 EAN 8
- D.4.7 UPC-A
- D.4.8 UPC-E
- D.4.9 Code 93
- D.4.10 Codabar
- D.4.11 Interleaved 2 of 5
- D.4.12 GS1 DataBar
- D.4.13 2D PDF-417
- D.4.14 2D Micro PDF-417
- D.4.15 2D Data Matrix
- D.4.16 2D QR Code
- D.4.17 2D Maxicode
- D.4.18 2D Aztec
- D.4.19 Postal: PlaNET
- D.4.20 Postal: PostNET
- D.4.21 Postal: Australian
- D.4.22 Postal: Canadian
- D.4.23 Postal: Japanese
- D.4.24 Postal: Kix
- D.4.25 Postal: Korean
- D.4.26 Postal: Royal
Chapter 5: Configuration
Profiles
150 Psion Teklogix Omnii Hand-Held Computer User Manual
• Always on – the GPS module is powered on at all times regardless of the power state of
the hand-held (suspend or standby).
• On, and off in suspend – the GPS module is powered on, but if Omnii is in suspend
mode, the GPS module is turned off.
5.9.2 Profiles
Tapping on the GPS Profile Selection drop-down menu allows you to choose an appropriate
profile: Default, Automotive or Pedestrian.
• Default profile is a good general profile suitable for most uses.
• Automotive profile is designed for in-vehicle use, providing quick location updates as
the vehicle moves. When the GPS module is set to this profile and the vehicle enters an
area such as a tunnel where satellite coverage is interrupted, it will attempt to predict the
vehicle position.
• Pedestrian profile is designed for those using the GPS module while walking. It takes
into account the slower pace of the pedestrian when mapping the location of the user.
When the GPS module is set to this profile and the operator moves into an area where
satellite coverage is interrupted, the GPS module will not attempt to predict the opera-
tor’s movement.
5.9.3 Programs
Tap on the GPS Program Port drop-down menu to choose the communication (COM)
port that the GPS software will use to communicate with the GPS receiver.