User's Manual
Table Of Contents
- Appendix A
- Appendix B
- Appendix C
- Bar Code Settings - TBD
- C.2 Decoded (Internal) Scanners
- C.2.1 Options
- C.2.2 Decoded (Internal) Advanced Options
- C.2.3 Decoded (Internal) Data Options
- C.2.4 Code 39
- C.2.5 Code 128
- C.2.6 EAN 13
- C.2.7 EAN 8
- C.2.8 UPC A
- C.2.9 UPC E
- C.2.10 UPC/EAN Shared Settings
- C.2.11 Code 93
- C.2.12 Codabar
- C.2.13 MSI Plessey
- C.2.14 Interleaved 2 of 5
- C.2.15 Discrete 2 of 5
- C.2.16 RSS Code (Reduced Space Symbology)
- C.2.17 Composite
- C.2.18 PDF-417
- C.2.19 Micro PDF-417
- C.3 Decoded (HHP)
- C.4 Decoded (Intermec ISCP)
- C.4.1 Decoded (ISCP) Options
- C.4.2 Decoded (ISCP) Advanced Options
- C.4.3 Code 39
- C.4.4 Code 128
- C.4.5 EAN 13
- C.4.6 EAN 8
- C.4.7 UPC A
- C.4.8 UPC E Settings
- C.4.9 UPC/EAN Shared Settings
- C.4.10 Code 93
- C.4.11 Codabar
- C.4.12 MSI Plessey
- C.4.13 Code 11
- C.4.14 Interleaved 2 of 5
- C.4.15 Matrix 2 of 5
- C.4.16 Discrete 2 of 5
- C.4.17 Telepen
- C.4.18 RSS Code (Reduced Space Symbology)
- C.4.19 Composite
- C.4.20 TLC-39
- C.4.21 PDF-417
- C.4.22 Micro PDF-417
- C.4.23 Codablock
- C.5 Non-Decoded Scanners
- Appendix D
- Teklogix Imagers Applet
- D.1 Required Applets
- D.2 Presets
- D.3 Using the Teklogix Imagers Applet
- D.3.1 Configuring the Image Capture Presets (Imaging Tab)
- D.3.2 Configuring the Bar Code Decoding Camera Presets (Barcoding Tab)
- D.3.3 Configuring the Bar Code Decoding Symbologies (Barcoding Tab)
- D.3.4 Barcoding Tab – Configuring Symbologies
- D.3.5 Filter Tab – Manipulating Bar Code Data
- D.3.6 Translation Tab – Configuring Rules
- D.3.7 Advanced Tab
- D.4 Bar Code Symbologies – Descriptions
- D.4.1 Options
- D.4.2 All 1D With Strong Recovery Enabled
- D.4.3 Code 39
- D.4.4 Code 128
- D.4.5 EAN 13
- D.4.6 EAN 8
- D.4.7 UPC-A
- D.4.8 UPC-E
- D.4.9 Code 93
- D.4.10 Codabar
- D.4.11 Interleaved 2 of 5
- D.4.12 GS1 DataBar
- D.4.13 2D PDF-417
- D.4.14 2D Micro PDF-417
- D.4.15 2D Data Matrix
- D.4.16 2D QR Code
- D.4.17 2D Maxicode
- D.4.18 2D Aztec
- D.4.19 Postal: PlaNET
- D.4.20 Postal: PostNET
- D.4.21 Postal: Australian
- D.4.22 Postal: Canadian
- D.4.23 Postal: Japanese
- D.4.24 Postal: Kix
- D.4.25 Postal: Korean
- D.4.26 Postal: Royal
Chapter 5: Configuration
Ports Tab
Psion Teklogix Omnii Hand-Held Computer User Manual 167
5.12.4 Ports Tab
Figure 5.5 Console and Port Replicator Port Settings
While you cannot configure the scanner, you can configure communications with a serial
decoded scanner using the options in this tab.
Use these settings to ensure that the communication ports on Omnii match the settings of the
serial devices to which they are connected. If the settings do not match exactly, the devices
may not function. Note that some devices can auto-detect serial port settings (such as baud
rate), and in this case Omnii will dictate the settings. Baud rates often have a direct impact
on performance—they should be set as high as possible while still ensuring reliable
communication.
5.12.4.1 Port Replicator Port A (COM5) and Port B (COM6)
Port Replicator Port A (COM5) and Port B (COM6) are standard RS-232 DE-9 DTE ports
on the Omnii port replicator module, available on some snap modules and cradle types.
Enabled
This parameter must be set to ON in order for Omnii to recognize the device connected to
the Port Replicator 9-pin (COM5).
Power (COM6 only) - TBD
Pin 9 on Omnii COM6 is reserved for 5V power out and is defaulted to OFF. This parameter
must be set to ON to enable power to a Snap Module or Vehicle cradle.