User's Manual
Table Of Contents
- Appendix A
- Appendix B
- Appendix C
- Bar Code Settings - TBD
- C.2 Decoded (Internal) Scanners
- C.2.1 Options
- C.2.2 Decoded (Internal) Advanced Options
- C.2.3 Decoded (Internal) Data Options
- C.2.4 Code 39
- C.2.5 Code 128
- C.2.6 EAN 13
- C.2.7 EAN 8
- C.2.8 UPC A
- C.2.9 UPC E
- C.2.10 UPC/EAN Shared Settings
- C.2.11 Code 93
- C.2.12 Codabar
- C.2.13 MSI Plessey
- C.2.14 Interleaved 2 of 5
- C.2.15 Discrete 2 of 5
- C.2.16 RSS Code (Reduced Space Symbology)
- C.2.17 Composite
- C.2.18 PDF-417
- C.2.19 Micro PDF-417
- C.3 Decoded (HHP)
- C.4 Decoded (Intermec ISCP)
- C.4.1 Decoded (ISCP) Options
- C.4.2 Decoded (ISCP) Advanced Options
- C.4.3 Code 39
- C.4.4 Code 128
- C.4.5 EAN 13
- C.4.6 EAN 8
- C.4.7 UPC A
- C.4.8 UPC E Settings
- C.4.9 UPC/EAN Shared Settings
- C.4.10 Code 93
- C.4.11 Codabar
- C.4.12 MSI Plessey
- C.4.13 Code 11
- C.4.14 Interleaved 2 of 5
- C.4.15 Matrix 2 of 5
- C.4.16 Discrete 2 of 5
- C.4.17 Telepen
- C.4.18 RSS Code (Reduced Space Symbology)
- C.4.19 Composite
- C.4.20 TLC-39
- C.4.21 PDF-417
- C.4.22 Micro PDF-417
- C.4.23 Codablock
- C.5 Non-Decoded Scanners
- Appendix D
- Teklogix Imagers Applet
- D.1 Required Applets
- D.2 Presets
- D.3 Using the Teklogix Imagers Applet
- D.3.1 Configuring the Image Capture Presets (Imaging Tab)
- D.3.2 Configuring the Bar Code Decoding Camera Presets (Barcoding Tab)
- D.3.3 Configuring the Bar Code Decoding Symbologies (Barcoding Tab)
- D.3.4 Barcoding Tab – Configuring Symbologies
- D.3.5 Filter Tab – Manipulating Bar Code Data
- D.3.6 Translation Tab – Configuring Rules
- D.3.7 Advanced Tab
- D.4 Bar Code Symbologies – Descriptions
- D.4.1 Options
- D.4.2 All 1D With Strong Recovery Enabled
- D.4.3 Code 39
- D.4.4 Code 128
- D.4.5 EAN 13
- D.4.6 EAN 8
- D.4.7 UPC-A
- D.4.8 UPC-E
- D.4.9 Code 93
- D.4.10 Codabar
- D.4.11 Interleaved 2 of 5
- D.4.12 GS1 DataBar
- D.4.13 2D PDF-417
- D.4.14 2D Micro PDF-417
- D.4.15 2D Data Matrix
- D.4.16 2D QR Code
- D.4.17 2D Maxicode
- D.4.18 2D Aztec
- D.4.19 Postal: PlaNET
- D.4.20 Postal: PostNET
- D.4.21 Postal: Australian
- D.4.22 Postal: Canadian
- D.4.23 Postal: Japanese
- D.4.24 Postal: Kix
- D.4.25 Postal: Korean
- D.4.26 Postal: Royal
Psion Teklogix Omnii Hand-Held Computer User Manual C-7
Appendix C: Bar Code Settings - TBD
Decoded (Internal) Scanners
Decoded (Internal) Advanced Options
Low Power Timeout
To extend laser life, you can select the time the scanner remains active following a success-
ful decode. The scanner wakes from low power mode when a bar code is scanned—a
successful decode restores normal flashing.
This is only used if the unit’s Trigger Mode has been changed to Continuous On. If the
unit is used in a fixed mount this parameter might be used, but not if the unit is used as
a hand-held.
When you double-tap on this parameter, a dialog box is displayed in which you can choose a
value of 30 sec., 1 min., 2 min. or 3 min.
Parameter Scanning
Setting this parameter to on enables decoding of parameter bar codes.
Linear Security Level
This parameter allows you to select the security level appropriate for your bar code quality.
There are four levels of decode security for linear code types (e.g., Code 39,
Interleaved 2 of 5). Higher security levels should be selected for decreasing levels of bar
code quality. As security levels increase, the scanner’s decode speed decreases.
Double-tapping on this parameter displays a dialog box in which you can enter a value from
1 to 4.
Linear security level 1 specifies that the following code types must be successfully read
twice before being decoded:
Linear security level 2 specifies that all types of codes must be successfully read twice
before being decoded.
Note: This parameter is only used if the Trigger Mode has been set to Continuous On and
Omnii is mounted in a fixed position; otherwise, ‘Low Power Timeout’ is not used.
Code Type Length
Codabar All
MSI Plessey 4 or less
D 5 of 5 8 or less
I 2 of 5 8 or less