Chapter 4: Configuration Ports When you choose a rule, an associated screen is displayed in which you can define the rule. 4.20.3.1 Case Rules The case rules are defined as follows: • • • • • • • No rule — ignored. Search and replace — replaces all instances of the match string. (Note that this rule cannot fail.) Match at index — matches the match string at a specified index. Match and replace at index — matches the match string at a specified index and replaces/changes it.
Chapter 4: Configuration Ports Note that some devices can auto-detect serial port settings (such as baud rate), and in this case the 8516 will dictate the settings. Baud rates often have a direct impact on performance—they should be set as high as possible while still ensuring reliable communication. 4.20.4.
Chapter 4: Configuration Storage Manager Double-tapping on Trigger On Sequence or Trigger Off Sequence displays a screen with a hex array of 10 elements. These parameters work in conjunction with Manage Triggers sending on and off data streams to the trigger module you assigned. For example, suppose you launch Manage Triggers and choose Decoded Scanner as the ‘module to trigger’. Next, you assign a ‘trigger key’—for this example, . (period).
Chapter 4: Configuration Partition Management 1. Press the New button next to the Partitions list box. The Create New Partition dialog box appears: 1. 2. Type a name for the partition. If more than one partition is desired, uncheck the Use All Available Diskspace checkbox, then specify the desired number of sectors to be used by the partition. Press OK. The new partition appears in the Partitions list. 1. The new partition is automatically mounted.
Chapter 4: Configuration Partition Management 2. Tap the Delete button. A warning dialog appears. 3. Tap the OK button. The partition is deleted. To format a partition: 1. 2. 3. 4. Choose the desired partition. Tap the Properties button. The Partition Properties dialog appears. Tap the Dismount button. The partition is dismounted. The asterisk disappears next to its name in the partitions list. Tap the Format button. The Format dialog appears: 5. Choose your format options.
Chapter 4: Configuration Stylus Properties 4.22 Stylus Properties Note: Touchscreen calibration may not be enabled on your unit. If your screen appears to require recalibration, contact your supervisor. • 4.22.1 Double-Tap • 4.22.2 In the Control Panel, choose the Stylus icon. In the Double-Tap menu, follow the directions to tailor the sensitivity of the stylus when you tap on the touchscreen. Calibration Touchscreens rarely require recalibration.
Chapter 4: Configuration System Properties • 4.23 Choose the Touch tab. Select the checkbox next to Disable the touch panel. System Properties This program identifies the computer’s software and hardware components, indicating which components are installed, their identification, version or pa numbers, and whether they are enabled or disabled. 96 • In the Control Panel, choose the System Properties icon. • By choosing the Expo button, you can create a log (SystemPropeies.
Chapter 4: Configuration Total Recall 4.24 Total Recall Total Recall is a Psion utility developed to maintain applications and settings during a cold boot, as well as clone settings to other devices. This utility creates a restore point of a device at a known state.
Chapter 4: Configuration Creating a Clone Important: Any profile not stored in persistent memory (Flash Disk, external USB drive) will be erased during a clean boot, therefore you should store profiles on a persistent drive. When performing an autorestore, the program only searches for the profile located in the \Flash Disk\TotalRecall folder. If you store your profile anywhere else it will not be restored. Only one profile can reside in that folder. - Tap on Start.
Chapter 4: Configuration Managing Profiles 4.24.3 Managing Profiles You can view profiles and choose profile options from the menus in this section. 4.24.3.1 Viewing a Profile • Tap on the Manage Profile button to see your list of profiles. Highlight a profile, and then you can choose to View the Profile Summary and go on to the next menu, Profile Details. List of profiles Profile Summary Profile Details 4.24.3.
Chapter 4: Configuration Deleting a Profile Upload to A.R.C – uploads the profile to the Active Remote Configuration server. After you tap on Send, a message will come up either confirming that the upload was complete or that the connection to the server failed. Clone to USB – writes a clone of the profile to the USB drive. After you tap on the button, a message will come up either confirming that the USB drive is ready for deployment, or that it is not available.
Chapter 4: Configuration TweakIt A warning pop-up screen appears asking if you’re certain that you want to delete this file. • 4.25 Tap on Yes to delete the file. TweakIt This utility allows you to ‘tweak’ or adjust Advanced system settings (interface, network, servers, driver, and radio) and provides a Registry Editor. 4.25.1 Advanced 4.25.1.1 Advanced CE Services Settings FTP Server This option is enabled by default to allow file transfers.
Chapter 4: Configuration Advanced 4.25.1.2 Advanced Interface and Network Settings Enable IPv6 This option allows you to enabled Internet Protocol specification, version 6, that has been published to enable 128-bit IP addresses (replacing version 4). Modem Logging When this option is enabled, the 8516 logs AT commands (e.g., dial-out information, password string, etc.) that the administrator can monitor for debugging purposes. Modem commands are stored in: \MdmLog.t. 4.25.1.
Chapter 4: Configuration Wi-Fi Config 4.28 Wi-Fi Config The Wi-Fi Config application is used to configure the 8516 802.11a/b/g/n radio for one or more wireless network profiles. A network profile contains settings for SSID (Service Set Identifier) and security options. Note: In most situations, the configuration of your 802.11 radio will require parameter setting and access keys from a network administrator. To launch the Wi-Fi Config application: • Tap on Start>Programs>Wi-Fi Config.
Chapter 4: Configuration Wi-Fi Config: Configure Connect: Used to connect to an already existing wireless network configuration. Add New: Used to create a new wireless network configuration. Edit: Used to change values in an already existing wireless network configuration. Remove: Used to delete a wireless network configuration. Scan: Used to detect and list available wireless networks. You can highlight a network in the list, and tap on Add New to activate the network.
Chapter 4: Configuration Wi-Fi Config: Configure Note: Each Auth. Mode has a unique Configure Profile screen attached to it with fields appropriate to the authorization mode you’ve chosen. Open Authentication Open authentication does not provide security. When this option is chosen, the 8516 will connect to wireless networks which do not use authentication or encryption. WEP (Wired Equivalent Privacy) WEP provides static security to prevent others from accidentally accessing your network.
Chapter 4: Configuration Wi-Fi Config: Configure 4.28.2.4 EAP This menu allows you to choose the EAP (Extensible Authentication Protocol) type used for 802.1x authentication to an access point. The following EAP types are supported by Wi-Fi Config: • • • • • • • TLS: Provides strong security via the use of client certificates for user authentication. PEAPv0-MSCHAPv2: Provides secure user authentication by using a TLS tunnel to encrypt EAP traffic. MSCHAPv2 is used as the inner authentication method.
Chapter 4: Configuration Configuring TCP/IP 4.28.2.7 Connecting the Wireless Network Your configured network is listed in the Configure tab. An [X] next to a network indicates that this is the network to which the 8516 will connect. • Tap on the Connect button to activate your network. The Status tab is displayed. The Status field displays ASSOCIATING while the 802.11a/b/g/n radio attempts to connect to the network.
Chapter 4: Configuration Configuring TCP/IP • Tap on the radio icon in the taskbar, or Tap on Start>Settings>Network and Dial-up Connections. Tap on the radio icon for which you want to assign an IP address—in the sample screen below, the icon is labelled SDIO86861. The Wireless Statistics screen is displayed. • Tap on the IP Information tab. Figure 4.7 SDIO86861 IP Information Note: When DHCP is enabled, tapping the ‘Renew’ button forces the 8516 to renew or find a new IP address.
Chapter 4: Configuration Wi-Fi Config: Advanced To define a static IP address: • Tap on the Configure button. • • Tap on the radio button next to Specify an IP address to select it. Type an IP, Subnet Mask and Default Gateway address in the appropriate fields. Press [ENTER] to save your information. 4.28.3.2 Name Server Note: If DHCP is enabled, name server addresses are assigned automatically. • • In the SDIO86861 IP Information tab (see Figure 4.7), tap on the Configure button.
Chapter 4: Configuration Monitoring the Network Connection Tap here to add a checkmark to activate the Windows radio configuration. Power Save Mode This allows you to set the 802.11 power saving mode of the radio to: CAM (continuous access—always on) (recommended); or MAX_PSP (maximum power saving mode). Roaming - RSSI Threshold This sets the RSSI threshold value, below which the radio will start scanning for new access points when roaming. Values range from -55 to -90 dBm.
Chapter 4: Configuration WiFi Connect A.R.C. When you click on this icon, WiFiConnect A.R.C. configures the default WiFi interface. The WEP key is set to PsionPsion123. The SSID is set to Psion. The default interface becomes the active interface. Keep in mind that you must configure the access point and the Vehicle-Mount(s) to use the same settings. Refer to the Active Remote Configuration (A.R.C.) Administrators Guide, PN 8000252, for details about updating devices on your network.
Chapter 5: Accessories Network Access • 5.4.1 Connect your network Ethernet cable to the Ethernet port on the adaptor cable. Network Access The 8516 automatically loads the appropriate drivers to communicate with the USB-Ethernet converters. Network Addressing The host application uses standard TCP/IP protocol to name, locate, and communicate with a specific 8516 on the network.
Chapter 5: Accessories Component Part Numbers Important: Safeguards To avoid possible injury, this device must be properly secured when in a moving vehicle. Keep this device away from magnetic fields. Do not place the computer near a television or radio receiver. Do not disassemble your 8516 computer — there are no user-serviceable parts inside. 5.5.1 Component Part Numbers The table below lists the mounting component part numbers and legend for Figure 5.10 on page 129. Table 5.
Chapter 5: Accessories Preparation 5.5.3 Figure 5.4 Bolt Hole Pattern For RAM Vesa Base Figure 5.5 Bolt Hole Pattern For RAM Circular Base Preparation The RAM articulating mount can be installed in a variety of orientations (see Figure 5.6 on page 127). Select the best orientation for your specific application. Preferred orientations maintain the centre of mass of the computer assembly, directly over the centre of the base (see Figure 5.6).
Chapter 5: Accessories Preparation Figure 5.6 Orientation Of Vehicle-Mount Assembly 15° 70° Important: The tilt and rotation of the cradle can be easily adjusted by the operator. Ensure that if the handscrew is loosened and the cradle slips, the operator and any equipment cannot be damaged by it. Also note that under extreme vibration, the mount may slowly ‘settle’, requiring readjustment and tightening of the handscrew.
Chapter 5: Accessories Installation 5.5.4 Installation Figure 5.8 8516 Vehicle-Mount Computer With Mounting Bracket Back of 8516 showing location of screw holes. A B C D 1. 1. • • Attaching the mounting bracket and RAM base to the computer: The kit provides four screws and washers that are used to secure the mounting bracket to the computer. Figure 5.8 provides a diagram and a legend to help you attach the mounting bracket and the RAM Vesa base to the computer.
Chapter 5: Accessories Positioning the 8516 1. • • 5.5.4.1 Use the supplied bolt hole pattern to drill the required holes in the local platform. Hole diameters must not exceed 10mm [13/32 inches]. Hardware (G, H, C, and J) for securing RAM Bases (B or F) to the local platform are in the recommended sizes (see Table 5.1 on page 125). If replacement hardware is required, it should be consistent with these diameters.
Chapter 5: Accessories Optional Mount Kits Figure 5.11 Circular Base and Vesa Base Mount Orientations 15° 15° 70° 70° Circ. Base To Platform 5.5.6 Vesa Base To Platform Optional Mount Kits One of the mounting kits shown in Figure 5.12 on page 130 may be substituted for the Vesa Base (B) or the circular base (F) when mounting to a post or forklift roll cage. To Install: Mount the Clamp Base and Lower Base around the shaft. Place the Screw through the Clamp and the Lower Base, and affix with the Nut.
Chapter 5: Accessories MT3250 Quick Release Mount “Turn & Lock” 5.6 MT3250 Quick Release Mount “Turn & Lock” The Quick Release Mount “Turn & Lock” option allows a dismount with a quick flick of the wrist and without the need of tools. It can be used alone or in combination with the RAM mounts. The Quick Release Mount can be used direct with the 8516 without the need for an adaptor plate. Figure 5.13 MT3250 Quick Release Mount “Turn & Lock” 5.7 8516 Vehicle-Mount Computer Installation 5.7.
Appendix A: 8516 Specifications The 8516 Vehicle-Mount Computer A.1 The 8516 Vehicle-Mount Computer Note: Performance specifications are nominal and subject to change without notice. A.1.1 Hardware Physical Dimensions • 275 mm W x 235 mm H x 90 mm D (10.83"x 9.25" x 5.54"). Weight • 4.3 kg (9.5 lbs), includes integrated UPS battery. Processor and Memory • Texas Instruments® OMAP3® Processor 800 MHz. • RAM: 512 MB RAM standard. • Flash ROM: 1 GB. Operating System • Microsoft Windows® Embedded CE 6.0 A.
B APPENDIX: PORT PINOUTS BPort Pinouts B.1 B.2 B.3 Serial Port Interface Pinout (DB-9 male) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 Enhanced USB1 Port Interface Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 Enhanced USB2 Port Interface Pinout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Appendix B: Port Pinouts Serial Port Interface Pinout (DB-9 male) B.1 Serial Port Interface Pinout (DB-9 male) Table B.
Appendix B: Port Pinouts Enhanced USB2 Port Interface Pinout B.3 Enhanced USB2 Port Interface Pinout Table B.3 Enhanced USB2 Pinout* Signal # Function Signal Type Notes 1 USB– VBUS DCD USB Switched 5V @ 0.
C APPENDIX: IMAGER & CAMERA SETTINGS CImager & Camera Settings C.1 C.2 C.3 C.4 Required Applets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.2.1 Predefined Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C.2.2 Barcode Predefined Presets (Barcoding Menu). . . . . . . . . . . . . . . C.2.2.1 Barcode Decoding Symbology Predefined Presets . . . . . . . C.2.
Appendix C: Imager & Camera Settings Required Applets The Imagers applet is used to create, modify, delete, and activate imager settings. The principal uses of the application are to decode barcodes and to capture images. This imager services application is used for cameras and imagers to configure linear (1D), stacked linear, matrix (true 2D) and postal barcodes. A Demonstration Application is provided to demonstrate how the imager works. Refer to “Demo” on page 27 for details. C.
Appendix C: Imager & Camera Settings Image Capture Predefined Presets (Imaging Menu) Note: It is recommended that the default preset be used whenever possible. My Default This preset uses the Symbology Settings menu to define the preset. For details about the Symbology Settings menu, refer to “Barcoding Menu – Configuring Symbologies” on page C-12. Factory Default This preset enables the decoding of frequently used barcodes. All This preset enables the decoding of all barcodes that the imager can decode.
Appendix C: Imager & Camera Settings Using the Imagers Applet Motion This preset uses a shoer exposure time so as to freeze motion. Low Light Near This preset is designed for dark conditions, it uses a longer exposure time and includes the flash. C.3 Using the Imagers Applet C.3.1 Configuring the Image Capture Presets (Imaging Menu) To configure the image capture presets, open the dialog box as follows: • • Tap on Sta>Settings>Control Panel.
Appendix C: Imager & Camera Settings Configuring the Image Capture Presets (Imaging Menu) C.3.1.3 Viewing a Preset To view the parameter settings in a preset: • Highlight a preset, and double-tap on the View button. The associated preset window is displayed. • C.3.1.4 Tap on the + sign to expand the lists so that you can view the parameter settings. Creating a Custom Preset A new custom preset is created by modifying a preset—either a predefined preset or an existing custom preset.
Appendix C: Imager & Camera Settings Configuring the Barcode Decoding Camera Presets (Barcoding Menu) • • • Tap on the + symbols to expand the lists so that you can view the parameter settings. Scroll through the parameter list until you reach the parameter that you want to change. For a parameter that can take a range of values: - Highlight the parameter, and then press the [SPACE] key or double-click on the parameter.
Appendix C: Imager & Camera Settings Configuring the Barcode Decoding Camera Presets (Barcoding Menu) Figure C.2 Camera Presets Note: The top poion of the window displays the barcode decoding camera presets. This window lists all the presets, both predefined and the custom. Presets are identified as follows: • • • • C.3.2.1 Predefined presets are marked as read-only. For a description, review “Predefined Presets” on page C-3. Predefined presets are marked as ‘R’ read-only.
Appendix C: Imager & Camera Settings Configuring the Barcode Decoding Camera Presets (Barcoding Menu) • C.3.2.4 Tap on the + sign to expand one of the lists so that you can view the parameter settings. Creating a Custom Preset A new custom preset is created by modifying a preset—either a predefined preset or an existing custom preset. To create a custom preset: • Highlight a preset, and tap on the Add button. A screen like the sample following is displayed.
Appendix C: Imager & Camera Settings Configuring the Barcode Decoding Symbologies (Barcoding Menu) • • Scroll through the parameter list until you reach the parameter that you want to change. For a parameter that can take a range of values: - Highlight the parameter, and then press the [SPACE] key or double-click the parameter. - An associated dialog box containing the valid range of values for the parameter and the current setting like the sample screen following is displayed.
Appendix C: Imager & Camera Settings Configuring the Barcode Decoding Symbologies (Barcoding Menu) Note: The bottom poion of the window displays the barcode decoding barcode presets. C.3.3.1 Setting the Active Preset An active preset has an A to the right; in Figure C.3 on page 10, the active preset is Default. To set an active preset: • C.3.3.2 Highlight the preset, and tap on the Activate button.
Appendix C: Imager & Camera Settings Barcoding Menu – Configuring Symbologies • • • Tap on the + symbols to expand the lists and view the parameter settings. Scroll through the parameter list until you reach the parameter that you want to change. For a parameter that can take a range of values: - Highlight the parameter, and then press the [SPACE] key or double-click the parameter.
Appendix C: Imager & Camera Settings Filter Menu – Manipulating Barcode Data C.3.5 Filter Menu – Manipulating Barcode Data To configure rules for manipulating barcode data: • • C.3.5.1 Tap on Sta>Settings>Control Panel. Tap on the Imagers icon, and then tap on the Filter tab. Modifying a Barcode Setting The rules for manipulating data from selected barcode symbologies can be modified.
Appendix C: Imager & Camera Settings Translation Menu – Configuring Rules C.3.6 Translation Menu – Configuring Rules Translation rules enable the automatic processing of barcode data. Up to 10 cases can be defined, each consisting of up to 10 sequential rules. Note: Changes made to the translations configuration using the Scanner Control Panel program are synchronized with changes made here. Changes made in either place affect both translation tables. • • Tap on Sta>Settings>Control Panel.
Appendix C: Imager & Camera Settings Barcode Symbologies • • • C.3.7.2 Type the file Name, choose the Folder and file Type. Choose the Location in which your files will be saved. When you have completed all the changes, tap on the Save button. Configuring Triggers Viewing the Trigger Configuration The trigger on the 8516 is configured using the Manage Triggers applet. The Imagers applet provides a shocut to the Manage Triggers applet. • • In the Advanced tab, tap on the Trigger Control button.
Appendix C: Imager & Camera Settings Barcode Symbologies C-16 • Go to the Barcode Presets. • Tap on an Barcode Preset to display the barcode symbologies.
Appendix C: Imager & Camera Settings Imager Barcode Symbologies C.4.1 Imager Barcode Symbologies The barcode symbologies for the Imager are listed in this section. Table C.
Appendix C: Imager & Camera Settings Color Camera Barcode Symbologies C.4.2 Color Camera Barcode Symbologies The barcode symbologies for the Color Camera are listed in this section. Table C.
D APPENDIX: SCANNER SETTINGS DScanner Settings D.1 D.2 D.3 D.4 D.5 Barcode Settings . . . . . . . . . . . . . . . . . . . D.1.1 Scanner Options. . . . . . . . . . . . . . D.1.2 Restoring Default Settings . . . . . . . . Decoded (Internal) Scanners . . . . . . . . . . . . D.2.1 Options . . . . . . . . . . . . . . . . . . . D.2.2 Decoded (Internal) Advanced Options . D.2.3 Decoded (Internal) Data Options . . . . Decoded (HHP) . . . . . . . . . . . . . . . . . . . . Decoded (Intermec ISCP) . . . . . . .
Appendix D: Scanner Settings Barcode Settings D.1 Barcode Settings The Scanners icon in the Control Panel provides dialog boxes in which you can tailor barcode scanner configurations and choose the barcodes your scanner will recognize. The parameters are preset with the default settings of the decoded scanner installed in the unit. For a listing of available scanners and their specifications, please refer to Chapter A: “8516 Specifications”.
Appendix D: Scanner Settings Decoded (Internal) Scanners • Choose Default subtree to reset only the parameters in the symbology you selected, or choose Default all settings to reset all scanner parameters to default settings. To reset a single parameter to its default setting: D.2 • Press and hold on the parameter you want to reset. • Choose Default parameter to reset the parameter to the default setting. Decoded (Internal) Scanners • D.2.
Appendix D: Scanner Settings Decoded (Internal) Advanced Options Dot Time (msec) The value selected for Dot Time (msec) determines (in milliseconds) how long the targeting dot remains on before the scanner switches to a normal scan sweep. When you double-tap on this parameter, a dialog box is displayed in which you can enter a value of 0 msec, 200 msec or 400 msec. A value of 0 (zero) disables the target dot.
Appendix D: Scanner Settings Decoded (Internal) Data Options should be selected for decreasing levels of barcode quality. As security levels increase, the scanner’s decode speed decreases. Double-tapping on this parameter displays a dialog box in which you can enter a value from 1 to 4.
Appendix D: Scanner Settings Decoded (HHP) Delete Char Set ECIs Setting this parameter to on enables the scanner to delete any escape sequences representing Character Set ECIs (Eended Channel Interpretations [also known as GLIs]) from its buffer before transmission. When this parameter is enabled, the scanner transmits data from PDF417 and MicroPDF417 barcodes containing Character Set ECIs, even when the ECI Protocol is disabled.
Appendix D: Scanner Settings Decoded (ISCP) Advanced Options Double-tapping on this parameter displays a dialog box in which you can enter a value between 1 and 10 seconds. D.4.2 Decoded (ISCP) Advanced Options Continuous Scan Mode Setting this parameter to on keeps the laser on and continuously decoding as long as the scanner button is pressed and held down.
Appendix D: Scanner Settings Non-Decoded Scanners The barcode symbologies for the scanner are listed in Table D.2. Table D.
Appendix D: Scanner Settings Options D.5.1 Options • Tap on the + sign next to Options to display these parameters. Dot Time (msec) The value selected for “Dot Time (msec)” determines (in milliseconds) how long the targeting dot remains on before the scanner switches to a normal scan sweep. When you double-tap on this parameter, a dialog box is displayed in which you can enter a value from 0 to 3000. A value of 0 (zero) disables the target dot.