User's Manual

ManualsBrandsPsion ManualsElectronicsRFID MODULE LF-AIR200-G2-XMOD

October 23, 2007

DPD A00332 A00 Sheet 1 of 7

WORKABOUT PRO RFID MODULE LF-AIR200-G2-XMOD

EXPANSION MODULE INSTRUCTIONS

Important: All Approval and safety information is outlined in the ‘Workabout pro G2

Handheld-computer User Manual’ – part number 8100140A. This manual is available on

our website www.psionteklogix.com through the Teknet extranet

Installation of the RFID Module LF-AIR200-G2-XMOD:

Easily installable expansion modules for the WORKABOUT PRO allow you to customise this hand-held to

meet your specific mobile computing requirements. This chapter outlines how to install the RFID Module

LF-AIR200-G2-XMOD and the external RFID Antenna LF-AEA120-G2.

Before installing a module in the WORKABOUT PRO G2, all power sources must be turned off.

• Remove the batteries. If your unit is using AC power, disconnect it.

• Slide the switch to position OFF to shut off internal battery power.

With the power shut down, you can install the RFID Module LF-AIR200-G2-XMOD.

• Remove and discard the two screws on the bottom of the metal frame.

• Put the adapter board in the same alignment of the expansion connector on the WORKABOUT

PRO. Apply slight pressure to snap the module into place on the hand-held.

Summary of content (7 pages)

PAGE 1
WORKABOUT PRO RFID MODULE LF-AIR200-G2-XMOD EXPANSION MODULE INSTRUCTIONS Important: All Approval and safety information is outlined in the ‘Workabout pro G2 Handheld-computer User Manual’ – part number 8100140A. This manual is available on our website www.psionteklogix.com through the Teknet extranet Installation of the RFID Module LF-AIR200-G2-XMOD: Easily installable expansion modules for the WORKABOUT PRO allow you to customise this hand-held to meet your specific mobile computing requirements.
PAGE 2
• Use four screws provided to secure the module in place. • Stick the RFID Module LF-AIR200-G2-XMOD to the WORKABOUT PRO, as shown. • Fix it with the 2 added washers and screws. • Fix the four screws on the top of the end cap.
PAGE 3
• Slide the switch to the position ON to turn power back on. • Replace the back plate and batteries. For detailed instructions, pleased refer to the WORKABOUT PRO Hand-Held Computer User Manual. These manuals are available on our website www.psionteklogix.com through the Teknet extranet Installation of the external RFID Antenna LF-AEA120-G2: • The RFID Antenna LF-AEA120-G2 can easily be fixed to the reader by a so called Binder plug.
PAGE 4
• Put the Binder plug of the telescope antenna in the socket of the RFID Module LF-AIR200-G2XMOD. • Pay attention to the groove. • Follow the instructions of your Workabout PRO, to start a read. READING AREA: This area depend of the TAG type, TAG packaging, configuration of the WORKABOUT PRO (scanner, Compact flash…), environment (metallic or not).
PAGE 5
WORKABOUT PRO RFID MODULE LF-AIR200-G2-XMOD RFID Regulatory Information October 23, 2007 DPD A00332 A00 Sheet 5 of 7
PAGE 6
October 23, 2007 DPD A00332 A00 Sheet 6 of 7
PAGE 7
IMPORTANT NOTE FOR NORTH AMERICA: The RFID must not be used whilst the host WORKABOUT PRO is being powered by the ac/dc adaptor. FCC Information to Users: This product and it antennas must not be co-located or operated in conjunction with any other antenna or transmitter. Radiation Exposure Compliance This product complies with the FCC RF exposure limits for an uncontrolled environment. For continued compliance, the product must not be held closer than 20 cm from the rest of the body.