WORKABOUT PRO G2 RFID Reader HF-AM2-G2 User Manual
Title RFID reader HF-AM2-G2 User Manual Doc Type User Manual Doc Id TS A00350 Revision Date Name Status/Comment A00 12/12/07 F.DEBULOIS Initial Version Specifications are subject to change without notice Psion Teklogix™ is a trademark of Psion Teklogix Inc. Other product names mentioned in this document may be trademarks of Psion Teklogix Inc. or trademarks or registered trademarks of other hardware, software, or service providers and are used herein for identification purposes only.
Table of Content I. Important – read carefully............................................................................................. 4 II. Overview ..................................................................................................................... 4 II.1. Bill of Material ................................................................................................................. 4 II.2. Interface Board installation ...............................................................
I. Important – read carefully All Approval and safety information is outlined in the ‘Workabout pro G2 Handheld-computer User Manual’ – part number 8100140A. This manual is available on our website www.psionteklogix.com through the Teknet extranet II. Overview II.1. Bill of Material RFID Reader HF-AM2-G2 is composed of : - an interface board, connected in the Workabout Pro G2 Handheld computer - a reader board, with its built-in antenna - a flex cable, which connects the two boards.
II.2.
II.3. Reader Board Installation The reader board has to be installed in a specific endcap depending of the configuration: II.3.1. HF-AM2-G2 Endcap II.3.2.
III. Hardware installation III.1. Preparing Before installing a module in the WORKABOUT PRO G2, all power sources must be turned off. Remove the batteries. If your unit is using AC power, disconnect it.
III.2. Interface Board installation Plug the flex cable as shown Insert the bard as shown and screw the 4 provided screws III.3. Reader Board installation The reader board intends to fit in a specific endcap which depends on the desired configuration. Each following paragraph describes how to assemble every configuration. III.3.1.
Place the rubber inside the endcap… and press strongly Put silicon between the rubber and the reader board ….
III.3.2.
The first step is to build the fingerprint unit (top- subassembly) Here are the required parts - 1 MSO sensor 1 Top moulding 1 MSO plate 1 8-ways MSO cable 4 self tapping screws 4 washers 2 gaskets Prepare the gasket and the MSO sensor Place the gasket on the sensor as shown Place the sensor in the top moulding Check the gasket positioning RFID Reader HF-AM2-G2 – User Manual TS-A00350-A00 Page 11/19
Connect the MSO cable to the MSO sensor Prepare the MSO plate and its gasket Put the gasket on the plate as shown Place the cover on the top moulding Screw the 4 self tappings screws with their washer Put silicon in the MSO cable window to ensure proper sealing RFID Reader HF-AM2-G2 – User Manual TS-A00350-A00 Page 12/19
It is now time to perform final assembly: Insert the reader board in the rubber Insert the assembly in the endcap slot Stick the gasket around the smart card board connector Place the smart card board on the top of the endcap The smart card board and the reader board are plugged together with a 8-ways SIL connector Pass the 8 way connector of the fingerprint unit through the window of the endcap RFID Reader HF-AM2-G2 – User Manual TS-A00350-A00 Page 13/19
Close the endcap with the fingerprint unit and screw the 4 thorx screws Finish the endcap sealing with a silicon injection in the 8-way cable window. III.4. Endcap connection The endcap has to be connected to the interface board: III.4.1. HF-AM2-G2 Endcap Connect the flex cable from the interface board to the reader board.
III.4.2. SAGEM endcap dual reader with slot Connect the flex cable from the interface board to the reader board. And the MSO cable in the dedicated connector Screw then endcap III.5. Final steps Slide the switch located in the battery casing to position ON RFID Reader HF-AM2-G2 – User Manual TS-A00350-A00 Put back the batteries and close the battery cover.
IV. Reading Area This area depend of the TAG type, TAG packaging, configuration of the WORKABOUT PRO (scanner, Compact flash…), environment (metallic or not). V.
RFID Reader HF-AM2-G2 – User Manual TS-A00350-A00 Page 17/19
RFID Reader HF-AM2-G2 – User Manual TS-A00350-A00 Page 18/19
IMPORTANT NOTE FOR NORTH AMERICA: The RFID must not be used whilst the host WORKABOUT PRO is being powered by the ac/dc adaptor. FCC Information to Users: This product and it antennas must not be co-located or operated in conjunction with any other antenna or transmitter. Radiation Exposure Compliance This product complies with the FCC RF exposure limits for an uncontrolled environment. For continued compliance, the product must not be held closer than 20 cm from the rest of the body.
