User Manual PA3V PTN 40W Power Amplifier All Rights Reserved Version: PA3V2013V1.
40W Power Amplifier NOTICE: Please read this user manual carefully before using this product. This manual is only for operation instruction only, not for any maintenance usage. The functions described in this version are updated till May, 2013. Any changes of functions and parameters since then will be informed separately. Please refer to the dealers for the latest details. This manual is copyright PTN Electronics Limited. All rights reserved.
40W Power Amplifier Table of Contents 1. Introduction .................................................................................................................1 1.1 Introduction to PA3V ..........................................................................................1 1.2 Features ............................................................................................................1 1.3 Package Contents .................................................................................
40W Power Amplifier Introduction Introduction to PA3V PA3V is a 40 Watt power amplifier (Class-D) with output alternatively at 70V or 100V. It has 2 stereo inputs (1x3.5mm jack for line in, 2xRCA for L&R), 1 digital input & 1 balanced MIC. It is integrated with powerful functions, including ducking function, EQ control, MIC mixer etc, and MIC input supports 3 levels with condenser MIC, dynamic MIC & line audio input.
40W Power Amplifier Introduction of Product Appearance Introduction of Front Panel Figure 1 Front Panel No. Name ① Audio Input Selection ② Audio Control ③ Volume Adjustment Function To select the input audio source, after choosing the audio source, the corresponding LED indicator will be on. No.1 is for dual mono audio input (2 RCA connectors for L&R), No.2 is for stereo audio input (3.5mm mini jack), and No.3 is for digital fiber audio input.
40W Power Amplifier Introduction of Rear Panel Figure 2 Rear Panel No. ① Name Power Indicator ② Microphone input port ③ Audio Inputs ④ ID Code ⑤ IR Eye ⑥ Power Port ⑦ 2 x RCA ⑧ Digital Audio Input ⑨ RS232 ⑩ Audio Output Function Turns red when power on. 3-pole captive screw connector for microphone input, the dial switch in right side is to select the micro input kind, including 48V (for condenser microphone), MIC (for dynamic microphone) and LINE (for line audio). 3.
40W Power Amplifier speakers). COM is for grounding (GND). System Connection Usage Precautions 1) No working with empty load is allowed. 2) Speakers must be connected before power on. System Diagram Figure 3 System Diagram Audio Signal Connection Audio Output PA3V supports mono audio output, and the output voltage is 70V or alterative 100V. With its dual-purpose design, it can be applied in different areas. The end COM is for grounding.
40W Power Amplifier Figure 4 Audio Output Connection Audio Inputs PA3V provides with 2 stereo audio inputs, one microphone input and one digital fiber audio input. The following figure shows the audio input ports. Dial Switch, to select the MIC input mode, includes MIC (dynamic microphone), 48V (condenser microphone) and LINE (normal audio or wireless microphone).
40W Power Amplifier “-” and “ ” connect to ground, and “+” connects to signal. b) Balanced connection: “+” connects to positive, “-” connects to negative and “ connects to ground. ” LINE input When the switch turns to “LINE” (It has a low frequency characteristics, and wide frequency response in this mode), the microphone input is used for connecting with normal audio or wireless microphone output.
40W Power Amplifier Volume/EQ controlling The line volume and MIC volume can be controlled by the buttons. The MIC Volume/LINE volume/LINE bass/LINE treble will be selected by the buttons, and controlled up/down/mute by the function buttons.
40W Power Amplifier IR receiver, works together with the IR remote. Please point the IR remote at the IR receiver when use, to avoid getting out of control as there is no signal detected. 3.5mm jack Insert it into the specialized PA3 socket (3.5mm), to connect the IR receiver with PA3. Figure 9 IR Receiver Operations of Control Software Connection with Computer When the amplifier connects to the COM1 or COM2 of the computer with control software, users can control it by that computer.
40W Power Amplifier Running Environment While the control software is installed, we can activate the software through the RS232 port and set the parameters, to make it able to send RS232 commands to control PA3V. Function Settings With the control software, we can easily switch the input channel, mute the output, check the working status, and adjust the volume etc. Please refer the details in RS232 Communication Commands.
40W Power Amplifier RS232 Communication Commands Communication Protocol: RS232 Communication Protocol Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none Command Function Description Feedback Code 1A1. Switching the audio to input 1 A: 1 -> 1 2A1. Switching the audio to input 2 A: 2 -> 1 3A1. Switching the audio to input 3 A: 3 -> 1 0A0. Mute Audio of MIC and Line out Mute 1A0. Mute audio of MIC Mute MIC 2A0. Mute audio of line out Mute LIN 0A1.
40W Power Amplifier Notice: 1. The letter inside bracket [ ] is the variable code, which is changeable. 2. The bracket [ ] is not included to the RS232 commands. 3. Any dot “.” after the letters is part of the commands. 4. Ducking function: When input with MIC, the volume of the line audio will be automatically turned down to the preset volume level, if there is no input MIC audio signal after 5 seconds, then the volume will be automatically turned up to the original one.
40W Power Amplifier Specifications Audio Input Input Input Connector Input Impedance Audio General Frequency Response SNR Rated Power Output Audio Output 2 stereo audio 1 MIC 1 Digital fiber audio 2 RCA 1 3.5mm jack 1 3-pole 3.81mm captive screw connector 1 SPF fiber connector Output 1 mono amplifier Output Connector 1 3-pole 3.81mm captive screw connector >10KΩ Output Type Constant voltage 70V or 100V.
40W Power Amplifier Panel Drawing Figure 13 Panel Drawing Troubleshooting and Maintenance 1) When there is no output audio: Check if there is any signal at the input. Check if there is any signal at the output. We can check these by using an oscilloscope or a multimeter. If there is no signal input/output, maybe the input/output cables broken or the connectors loosen, please change for another cable. Check if the output port number is the same with the controlled one.
40W Power Amplifier Safety Operation Guide In order to guarantee the reliable operation of the equipments and safety of the staff, please abide by the following proceeding in installation, using and maintenance: 1) The system must be earthed properly. Please do not use two blades plugs and ensure the alternating power supply ranged from 100v to 240v and from 50Hz to 60Hz. 2) Do not put the switcher in a place of too hot or too cold.
40W Power Amplifier After-sales Service 1) If there appear some problems when running PA3V, please check and deal with the problems reference to this user manual. Any transport costs are borne by the users during the warranty. 2) You can email to our after-sales department or make a call, please tell us the following information about your cases. Product version and name. Detailed failure situations. The formation of the cases.
www.PTN-electronics.com PTN Electronics Limited Tel: +86-755-2846 1819 Fax: +86-755-8471 7796 Email: info@PTN-electronics.com Website: www.PTN-electronics.