VGA/Stereo Audio Selection Switcher 4X1 USER MANUAL WVG4A PTN VGA/Stereo Audio Selection Switcher 4x1 Version: WVG4A2013V1.1 PTN Electronics Limited www.PTN-electronics.
VGA/Stereo Audio Selection Switcher 4X1 NOTICE: Please read this user manual carefully before using this product. This manual is for operation instruction only, not for any maintenance usage. The functions described in this version are updated till May 2013. Any changes of functions and parameters since then will be informed separately. Please refer to the dealers for the latest details. This manual is copyright PTN Electronics Limited. All rights reserved.
VGA/Stereo Audio Selection Switcher 4X1 Table of Contents 1. Introduction ............................................................................................................1 1.1. Introduction to WVG4A .................................................................................. 1 1.2. Package Contents ......................................................................................... 1 2. Features ........................................................................................
VGA/Stereo Audio Selection Switcher 4X1 1. Introduction 1.1. Introduction to WVG4A WVG4A is a 4x1 selection switcher for VGA & stereo audio. It supports auto-switching and has a bandwidth up to3200*2400@60MHz. And the audio can be breaked away. It’s a high performance device for conference room, educational facility, multi-media meeting room, demonstration hall etc. 1.2.
VGA/Stereo Audio Selection Switcher 4X1 Return Loss Switching Speed Gain Audio Input Input Input Connector Audio Input Impedance Switching Speed -0.8dB -30dB@5MHz Crosstalk Input/Output Level I/O Impedance Audio Output Output Output Connector Audio Output Impedance Output Volume 200ns (Max.) 0dB 4 stereo audio 3.5mm mini jack connector >10KΩ 200ns (Max.) Output Bass Output Treble -50dB@5MHz 0.5Vp-p ~ 2.0Vp-p 75Ω 1 stereo audio 3.
VGA/Stereo Audio Selection Switcher 4X1 LED indicator of “Auto-SW” Press the buttons “Up”, “Down” to control the output volume up/down. (not including the bass/treble setting) Press the button “1” for 3 seconds, WVG4A will enter the auto-switching mode. The LED light of “Auto-SW” will be on. Please check the index”Auto-switching Function” for the auto-switching principle. And, pressing the button “1” for another 3 seconds, to quit the auto-switching and return to the manual-switching mode.
VGA/Stereo Audio Selection Switcher 4X1 the RS232 port is still available for controlling. 5.2. Connection with Control System With the RS-232 port, the switchers can be control by several kinds of control systems. This RS-232 communication port is a female 9-pin D connector. The definition of its pins is as the table below. No. Pin Function 1 N/u Unused 2 Tx Transmit 3 Rx Receive 4 N/u Unused 5 Gnd Ground 6 N/u Unused 7 N/u Unused 8 N/u Unused 9 N/u Unused 5.3.
VGA/Stereo Audio Selection Switcher 4X1 6. System Diagram 7. Auto-switching Function Under the auto-switching mode, WVG4A will detect the input source and switching automatically, following some priority principle: 1: Priority of the new connection When you connect a new valid VGA source to WVG4A, under the auto-switching mode, WVG4A will switch to this new source.
VGA/Stereo Audio Selection Switcher 4X1 EXAMPLE: Connect the input 2 and input 4 ports to the source devices, press and hold on the front key INPUT 1 for 3 seconds, the LED indicator Auto-SW will be on. Then WVG4A begins to run in auto-switching mode. WVG4A detects the signal from the port input 1 to input 4 one by one. When it detects that input 1 is not available, and then it turns to detect input 2.
VGA/Stereo Audio Selection Switcher 4X1 9. Communication Protocol and Command Codes Communication protocol: RS232 Controlling Protocol Command Type: ASCII Baud rate: 9600 Date bit: 8 Stop bit: 1 Parity bit: none Commands Function Description Return Code Preset the volume level, the [xx] is ranging 7[xx]% Volume :31 from "00" to "60". Preset the bass level, the [xx] is ranging from 8[xx]% Bass : 01 "00" to "14". Preset the treble level, the [xx] is ranging from 9[xx]% Treble : 01 "00" to "14".
VGA/Stereo Audio Selection Switcher 4X1 10. Troubleshooting & Maintenance 1) When there is no output images/sounds: Check if there is any signal at the input. Check if there is any signal at the output. We can check these by using an oscilloscope or a multimeter. If there is no signal input/output, maybe the input/output cables broken or the connectors loosen, please change for another cable. Make sure the destination device is exactly on the controlled output channel.
VGA/Stereo Audio Selection Switcher 4X1 12. After-sales Service 1) If there appear some problems when running WVG4A, please check and deal with the problems reference to this user manual. Any transport costs are borne by the users during the warranty. 2) You can email to our after-sales department or make a call, please tell us the following information about your cases. Product version and name. Detailed failure situations. The formation of the cases.