DANNOVO HD USB 3.0 PTZ Video Conference Camera User Manual V 2.3(ENGLISH VERSION) Please read this Manual before set up Camera, and stick to its requirements strictly for Safety reason. Suggest you save this manual for further inquires reference.
Precautions Safety Tips Please read this manual carefully before use the Camera. To avoid damage from stress, violent vibration, soaking during transportation, storage and installation. Take care of each components of Camera during installation, and install camera at where is affordable enough, to avoid drop or scratches of camera case. Do not apply excessive voltage. (Use only the specified voltage.) Otherwise, you may get an electric shock or a fire may occur.
Main Features Camera and Lens Video CMOS Sensor: 1/2.5 inch super quality HD CMOS transducer Image: 16:9 2.1 Mega pixel Video Format:YUY2|1920x1080P/30, 1280x720/60 Lens zoom: 10x optical zoom, f=4.5-45mm F1.8-2.2 Focus, 1.0Lux at F 1.8 Visual Angle: 5.
Rear Board & function Rear board of camera Front of HD Camera 3 VISCA RS232C IN Connector When connect multi cameras to PC via RS-232C (VISCA IN), use serial cable connect VISCA OUT of the first camera to VISCA IN of the second camera. 4 VISCA Out/RS-485 Control Interface Used for connect Chain Daisy of cameras, or RS485 Control. 5 1 DC12V 1.2A Power supply socket USB 3.0 interface Power on/off USB 3.
IR Remote Controller Front Panel: 1. Reset: Restart Camera and restore to factory default settings 2. Camera Selection Select Camera of IR 1,2,3 3. Preset positions 1-9: preset positions Set: Setting preset position Clear: Clear preset position Call: Call preset position Note: if you need set number 1 preset position, you should press Number key “1”, then press “Set” to setting this position; 4. Zoom in/out Control Zone +: Zoom in -: Zoom out 5.
S/N Regional 1 Reset 2 Camera ID Chose Keynote Restart Camera and back to default Factory settings. 1 ~ 3 1 3 Preset position function area ~ 9 Set Clear Call 4 Fast-speed Zoom in/out functions ＋ Chose camera according to your Remote control Chose serial no.
8 9 10 11 Power on/off Power-on/off Dome Login DOME OSD Menu Lens Login Lens OSD Menu ＋ Zoom in slowly speed OSD Menu Slow speed Zoom in/out Lens Focus adjustments Pan & Tilt Function area Zoom Slow － Zoom out slowly speed Auto Auto focus automatically Manual Manual focus Far Lens zoom in far end Near Lens zoom in Near end L-Limit Set Left points for boundary scanning Scan Enable Scanning automatically R-Limit Set Right limit point for Boundary scanning Home Home positio
turn left Left movement turn right Right movement Rotate left Zoom in Rotate right Zoom out Special Preset positions function Preset position No.
Specification sheet Model No. Image Sensor DN-HDC08B-CN Sensor 1/3" CMOS 2.1 Mega Pixel Effective Pixels Minimum Scene Illumination 2.1 Megapixel Color: 0.1Lux,Black/White: 0.01Lux White Balance Auto/Manual Gain Control Back-light compensation Auto On / Off E-Shutter 1/30s~1/10000S S/N Ratio > 50db Focus f=5-50mm Iris Auto/Manual Zoom 10x Optical Zoom Lens View Angle 52° Video Output USB 3.
Pan Rotation Angle 0~355degree Tilt Rotation Angle 90 degree Auto Pan Scan Support auto pan scan Boundary Scan 0-359 degree (programmable) Remote Controller IR wireless control P/T/Z Power Supply DC12V±10%,1.
Installation instruction Wall/Ceiling installation Mount kits provided with Camera in the package.
Tripod Installation To fix the round accessory on bottom board of camera, to match 2 screw position on the bottom board; To match the Tripod on bottom of camera; 18
Compatibility As we tested with Amcap S/W, Skype, Microsoft Lync, VSEE, Vidyo, DEBUT Software, most of them are Video Conferencing system application, and it works perfect; Troubleshooting Before request service to serviceman or manufacture, it can according to below methods to remove failures, if still can’t be solved, please contact to distributor or manufacture for help. Fault Phenomenon There is no power to camera. The video of camera cannot be displayed on the screen.
