Datasheet

ManualsBrandsPULS ManualsRack & DIN Rail Mount PSUsDIMENSION Rail mounted PSU (DIN) 6.7 A 240 W

CP10.361

CP-Series

36V, 6.7A, 240W, SINGLE PHASE INPUT

POWER SUPPLY

 AC 100-240V Wide-range Input

 Width only 39mm

 Efficiency up to 95.4%

 Excellent Partial Load Efficiency

 20% Output Power Reserves

 Safe Hiccup

PLUS

Overload Mode

 Active Power Factor Correction (PFC)

 Minimal Inrush Current Surge

 Full Power Between -25°C and +60°C

 DC-OK Relay Contact

 3 Year Warranty

1/29

GENERAL DESCRIPTION

The DIMENSION CP-Series units are high-end power

supplies in a medium price range without compromising

quality, reliability and performance. The CP-Series is

part of the DIMENSION power supply family. The most

outstanding features of CP10.361 are the high

efficiency, advanced inrush current limitation, active PFC

and the wide operational temperature range.

The CP-Series includes all the essential basic functions.

The devices have a power reserve of 20% included,

which may even be used continuously at temperatures

up to +45°C. Additionally, the CP10 can deliver three

times the nominal output current for at least 12ms

which helps to trip fuses on faulty output branches.

High immunity to transients and power surges as well as

low electromagnetic emission, a DC-OK relay contact

and a large international approval package for a variety

of applications makes this unit suitable for nearly every

situation.

SHORT-FORM DATA

Output voltage DC 36V Nominal

Adjustment range 36 – 42V Factory setting 36.0V

Output current 8.0-6.8A Below +45°C ambient

6.7-5.7A At +60°C ambient

5.0-4.3A At +70°C ambient

Derate linearely between +45°C and +70°C

Input voltage AC AC 100-240V -15%/ +10%

Mains frequency 50-60Hz ±6%

Input current AC 2.16 / 1.13A At 120 / 230Vac

Power factor 0.99 / 0.97 At 120 / 230Vac

Input voltage DC DC 110-150V ±20%

Input current DC 2.35A At 110Vdc

Input inrush current 6 / 9A pk At 40°C 120 / 230Vac

Efficiency 93.8 / 95.4% At 120 / 230Vac

Losses 15.9 / 11.6W At 120 / 230Vac

Hold-up time 38 / 38ms At 120 / 230Vac

Temperature range -25°C to +70°C

Size (w x h x d) 39x124x117mm Without DIN-Rail

Weight 600g / 1.3lb

ORDER NUMBERS

Power Supply CP10.361

Mechanical Accessory

ZM4.WALL Wall/panel mount bracket

ZM12.SIDE Side mount bracket

MARKINGS

For details and a complete approval list see section 20.

IND. CONT. E

UL 508

UL 60950-1

Class I Div 2

IECEx ATEX

Marine

Aug. 2017 / Rev. 1.1 DS-CP10.361-EN

All parameters are specified at 36V, 6.7A, 230Vac, 50Hz, 25°C ambient and after a 5 minutes run-in time unless otherwise noted.

www.pulspower.com Phone +49 89 9278 0 Germany

Summary of content (29 pages)

PAGE 1
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series POWER SUPPLY AC 100-240V Wide-range Input Width only 39mm Efficiency up to 95.
PAGE 2
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series INDEX Page 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. Intended Use .......................................................3 Installation Requirements...................................3 AC-Input...............................................................4 DC-Input...............................................................5 Input Inrush Current ...........................................6 Output .....................
PAGE 3
CP10.361 CP-Series 36V, 6.7A, 240W, SINGLE PHASE INPUT 1. INTENDED USE This device is designed for installation in an enclosure and is intended for the general professional use such as in industrial control, office, communication, and instrumentation equipment. Do not use this power supply in equipment, where malfunction may cause severe personal injury or threaten human life. 2. INSTALLATION REQUIREMENTS This device may only be installed and put into operation by qualified personnel.
PAGE 4
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 3. AC-INPUT AC input AC input range External input protection Nom. AC 100-240V Suitable for TN-, TT- and IT mains networks Min. 85-264Vac Continuous operation Min. 264-300Vac For maximal 500ms Max. 300Vac Continuous according to IEC 62477-1 Nom. 50–60Hz ±6% Typ. 80Vac Steady-state value, see Fig. 3-1 Typ. 70Vac Steady-state value, see Fig. 3-1 Typ. 55Vac Dynamic value for maximal 250ms See recommendations in chapter 24.3.
PAGE 5
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 4. DC-INPUT DC input DC input range DC input current Allowed Voltage L/N to Earth Turn-on voltage Shut-down voltage Nom. Min. Typ. Max. Typ. Typ. Typ. Fig. 4-1 Wiring for DC Input Battery + Power Supply AC L N PE - + Load - DC 110-150V 88-180Vdc 2.
PAGE 6
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 5. INPUT INRUSH CURRENT An active inrush limitation circuit (NTCs, which are bypassed by a relay contact) limits the input inrush current after turn-on of the input voltage. The charging current into EMI suppression capacitors is disregarded in the first microseconds after switch-on. Inrush current Max. Typ. Typ. Max. Inrush energy Fig.
PAGE 7
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 6. OUTPUT Output voltage Adjustment range Nom. Min. Max. Factory settings Line regulation Load regulation Ripple and noise voltage Output current Typ. Max. Max. Max. Nom. Nom. Nom. Nom. Nom. Nom. Typ. Overload behaviour Short-circuit current Output capacitance Min. Max. Max. Min. Typ. Typ. 36V 36-42V 44V Guaranteed value This is the maximum output voltage which can occur at the clockwise end position of the potentiometer due to tolerances.
PAGE 8
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series Fig. 6-2 Dynamic output current capability, typ. Fig. 6-1 Output voltage vs. output current, typ. Output Voltage Factory setting 24 42V Continuous current 36 30 Output Voltage (dynamic behavior, < 12ms) Adjustment Range 42V 36 Adjustment Range 30 24 18 18 HiccupPLUS mode 12 6 0 12 6 0 Output Current 1.5 0 3 4.5 6 9 10.5 12A 7.5 Output Current 0 3 6 9 12 15 18 21 24 27 30A Fig.
PAGE 9
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 8. DC-OK RELAY CONTACT This feature monitors the output voltage on the output terminals of a running power supply. Contact closes Contact opens As soon as the output voltage reaches typ. 90% of the adjusted output voltage level. As soon as the output voltage dips more than 10% below the adjusted output voltage. Short dips will be extended to a signal length of 100ms. Dips shorter than 1ms will be ignored. Typ. 1.5V Maximal 60Vdc 0.
PAGE 10
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 9. EFFICIENCY AND POWER LOSSES Efficiency Average efficiency*) Power losses *) Typ. Typ. Typ. AC 100V 93.1% 92.8% 92.4% AC 120V 93.8% 93.6% 93.1% AC 230V 95.4% 95.3% 94.3% Typ. Typ. Typ. Typ. 2.4W 9.5W 17.8W 22.3W 2.2W 8.3W 15.9W 19.7W 1.8W 7.0W 11.6W 14.2W At 36V, 6.7A At 36V, 8A (Power Boost) 25% at 1.7A, 25% at 3.4A, 25% at 5A. 25% at 6.7A At 36V, 0A At 36V, 3.35A At 36V, 6.
PAGE 11
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 10. LIFETIME EXPECTANCY The Lifetime expectancy shown in the table indicates the minimum operating hours (service life) and is determined by the lifetime expectancy of the built-in electrolytic capacitors. Lifetime expectancy is specified in operational hours and is calculated according to the capacitor’s manufacturer specification. The manufacturer of the electrolytic capacitors only guarantees a maximum life of up to 15 years (131 400h).
PAGE 12
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 12. FUNCTIONAL DIAGRAM Fig. 12-1 Functional diagram L N Input Fuse Input Filter Input Rectifier Inrush Current Limiter PFC Converter Power Converter Output Filter Output Voltage Regulator Temperature Shutdown Output Power Manager Output OverVoltage Protection Output Voltage Monitor + + VOUT DC-ok LED DC-ok Relay DC-ok Contact Aug. 2017 / Rev. 1.1 DS-CP10.361-EN All parameters are specified at 36V, 6.
PAGE 13
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 13. TERMINALS AND WIRING The terminals are IP20 finger safe constructed and suitable for field- and factory wiring. Input and output Screw terminals Max. 6mm2 Max. 4mm2 AWG 20-10 Max. 2.8mm (including ferrules) 7mm / 0.28inch 3.5mm slotted or cross-head No 2 1Nm, 9lb.in Type Solid wire Stranded wire American Wire Gauge Wire diameter Wire stripping length Screwdriver Recommended tightening torque DC-OK-Signal Push-in terminals Max. 1.5mm2 Max. 1.
PAGE 14
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 14. FRONT SIDE AND USER ELEMENTS Fig. 14-1 Front side A Input Terminals Screw terminals N, L Line input PE (Protective Earth) input B Output Terminals (two identical + poles and three identical - poles) Screw terminals + Positive output – Negative (return) output C Output voltage potentiometer Open the flap to adjust the output voltage. Factory set: 36.
PAGE 15
CP10.361 CP-Series 36V, 6.7A, 240W, SINGLE PHASE INPUT 15. EMC The power supply is suitable for applications in industrial environment as well as in residential, commercial and light industry environments.
PAGE 16
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series Switching Frequencies PFC converter Main converter Auxiliary converter 110kHz 84kHz to 140kHz 60kHz Fixed frequency Output load dependent Fixed frequency 16.
PAGE 17
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 17. PROTECTION FEATURES Output protection Output over-voltage protection Degree of protection Penetration protection Over-temperature protection Input transient protection Internal input fuse Electronically protected against overload, no-load and short-circuits. In case of a protection event, audible noise may occur. Typ. 46Vdc In case of an internal power supply defect, a redundant Max. 48Vdc circuit limits the maximum output voltage.
PAGE 18
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 19. DIELECTRIC STRENGTH The output voltage is floating and has no ohmic connection to the ground. Type and factory tests are conducted by the manufacturer. Field tests may be conducted in the field using the appropriate test equipment which applies the voltage with a slow ramp (2s up and 2s down). Connect all input-terminals together as well as all output poles before conducting the test.
PAGE 19
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 20. APPROVALS The CE mark indicates conformance with the - EMC directive, - Low-voltage directive (LVD) and the - ATEX directive CB Scheme, Information Technology Equipment EC Declaration of Conformity IEC 60950-1 2nd Edition UL 508 IND. CONT. EQ. UL 60950-1 2nd Edition ANSI / ISA 12.12.
PAGE 20
CP10.361 CP-Series 36V, 6.7A, 240W, SINGLE PHASE INPUT 22. PHYSICAL DIMENSIONS AND WEIGHT Width Height Depth Weight DIN-Rail Housing material Installation clearances 39mm 1.54’’ 124mm 4.88’’ 117mm 4.61’’ The DIN-rail height must be added to the unit depth to calculate the total required installation depth. 600g / 1.3lb Use 35mm DIN-rails according to EN 60715 or EN 50022 with a height of 7.5 or 15mm. Body: Aluminium alloy Cover: zinc-plated steel See chapter 2 Fig. 22-1 Front view Fig.
PAGE 21
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 23. ACCESSORIES 23.1. ZM4.WALL – WALL/PANEL MOUNT BRACKET This bracket is used to mount the devices on a wall/panel without utilizing a DIN-Rail. The bracket can be mounted without detaching the DIN-rail brackets. Fig. 23-1 Isometric view Fig. 23-4 Wall/panel mounting, front view Fig. 23-2 Isometric view Fig. 23-5 Hole pattern for wall mounting Fig. 23-3 Isometric view Fig. 23-6 Wall/panel mounting, side view Aug. 2017 / Rev. 1.1 DS-CP10.
PAGE 22
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 23.2. ZM12.SIDE - SIDE MOUNTING BRACKET This bracket is used to mount DIMENSION units sideways with or without utilizing a DIN-Rail. The two aluminum brackets and the black plastic slider of the unit have to be detached, so that the steel brackets can be mounted. For sideway DIN-rail mounting, the removed aluminum brackets and the black plastic slider need to be mounted on the steel bracket.
PAGE 23
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 23.3. REDUNDANCY MODULE YR2.DIODE – 2x 10A Inputs, 1x 20A output The YR2.DIODE is a dual redundancy module, which has two diodes as decoupling devices included. It can be used for various purposes. The most popular application is to configure highly reliable and true redundant power supply systems. Another interesting application is the separation of sensitive loads from non-sensitive loads.
PAGE 24
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 24. APPLICATION NOTES 24.1. PEAK CURRENT CAPABILITY The unit can deliver peak currents (up to several milliseconds) which are higher than the specified short term currents. This helps to start current demanding loads. Solenoids, contactors and pneumatic modules often have a steady state coil and a pick-up coil.
PAGE 25
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 24.2. BACK-FEEDING LOADS Loads such as decelerating motors and inductors can feed voltage back to the power supply. This feature is also called return voltage immunity or resistance against Back- E.M.F. (Electro Magnetic Force). This power supply is resistant and does not show malfunctioning when a load feeds back voltage to the power supply. It does not matter whether the power supply is on or off. The maximum allowed feed-back-voltage is 50Vdc.
PAGE 26
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 24.5. PARALLEL USE TO INCREASE OUTPUT POWER CP10.361 power supplies can be paralleled to increase the output power. The output voltage of all power supplies shall be adjusted to the same value (±100mV) with the same load conditions on all units, or the units can be left with the factory settings. There is no feature included which balances the load current between the power supplies.
PAGE 27
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series Unit A 24.7. SERIES OPERATION AC Power supplies of the same type can be connected in series for higher output voltages. It is possible to connect as many units in series as needed, providing the sum of the output voltage does not exceed 150Vdc. Voltages with a potential above 60Vdc are not SELV any more and can be dangerous. Such voltages must be installed with a protection against touching.
PAGE 28
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 24.10. OPERATION ON TWO PHASES Power Supply The power supply can also be used on two-phases of a three-phasesystem. Such a phase-to-phase connection is allowed as long as the supplying voltage is below 240V+10%. L3 Center Tap 240V +10% max. L1 AC L N PE DC L2 24.11. USE IN A TIGHTLY SEALED ENCLOSURE When the power supply is installed in a tightly sealed enclosure, the temperature inside the enclosure will be higher than outside.
PAGE 29
CP10.361 36V, 6.7A, 240W, SINGLE PHASE INPUT CP-Series 24.12. MOUNTING ORIENTATIONS Mounting orientations other than all terminals on the bottom require a reduction in continuous output power or a limitation in the maximum allowed ambient temperature. The amount of reduction influences the lifetime expectancy of the power supply. Therefore, two different derating curves for continuous operation can be found below: Curve A1 Curve A2 Recommended output current.