Datasheet

CP20.241, CP20.241-C1, CP20.241-S1,
CP20.241-S2, CP20.241-V1, CP20.242
CP-Series
24V, 20A, 480W, SINGLE PHASE
Sep. 2018 / Rev. 1.0 DS-CP20.241-EN - All parameters are typical values specified at 230Vac, 50Hz input voltage, 24V, 20A output load,
25°C ambient and after a 5 minutes run-in time unless otherwise noted.
www.pulspower.com Phone [phone] Germany
13. CONNECTION TERMINALS
The terminals are IP20 Finger safe constructed and suitable for field- and factory wiring.
CP20.241, CP20.241-C1,
CP20.241-V1, CP20.242
Input Output Signal Terminals
Type Screw termination Screw termination Push-in termination
Solid wire Max. 6mm
2
Max. 6mm
2
Max. 1.5mm
2
Stranded wire Max. 4mm
2
Max. 4mm
2
Max. 1.5mm
2
American Wire Gauge AWG 20-10 AWG 20-10 AWG 24-16
Max. wire diameter (including ferrules) 2.8mm 2.8mm 1.6mm
Recommended tightening torque Max. 1Nm, 9lb-in Max. 1Nm, 9lb-in -
Wire stripping length 7mm / 0.28inch 7mm / 0.28inch 7mm / 0.28inch
Screwdriver 3.5mm slotted or cross-
head No 2
3.5mm slotted or cross-
head No 2
3mm slotted to open
the spring
CP20.241-S1 Input Output Signal Terminals
Type Quick-connect spring-
clamp termination
Quick-connect spring-
clamp termination
Push-in termination
Solid wire Max. 6mm
2
Max. 6mm
2
Max. 1.5mm
2
Stranded wire Max. 4mm
2
Max. 4mm
2
Max. 1.5mm
2
American Wire Gauge AWG 20-10 AWG 20-10 AWG 24-16
Max. wire diameter (including ferrules) 2.8mm 2.8mm 1.6mm
Wire stripping length 10mm / 0.4inch 10mm / 0.4inch 7mm / 0.28inch
Screwdriver - - 3mm slotted to open
the spring
CP20.241-S2 Input Output Signal Terminals
Type Push-in termination Push-in termination Push-in termination
Solid wire Max. 2.5mm
2
Max. 10mm
2
Max. 1.5mm
2
Stranded wire Max. 2.5mm
2
Max. 6mm
2
Max. 1.5mm
2
Stranded wire with ferrules Max. 1.5mm
2
Max. 4mm
2
Max. 1.5mm
2
American Wire Gauge AWG 24-12 AWG 24-8 AWG 24-16
Max. wire diameter (including ferrules) 2.3mm 3.3mm 1.6mm
Wire stripping length 10mm / 0.4inch 15mm / 0.6inch 7mm / 0.28inch
Screwdriver 3.0mm slotted to open
the spring
3.5mm slotted to open
the spring
3mm slotted to open
the spring
Daisy chaining:
Daisy chaining (jumping from one power supply output to the next) is not allowed. Use a separate distribution
terminal block as shown in Fig. 13-1.
Fig. 13-1 Using distribution terminals
Distribution
Terminals
Load
+
-
Power
Supply
+ +
- -
Output
Power
Supply
+ +
- -
Output
15/32