Datasheet

ManualsBrandsPULS ManualsRack & DIN Rail Mount PSUsRail mounted PSU (DIN) DIMENSION 36 Vdc 13.3 A 576 W 1 x

CPS20.361

C-Series

36V, 13.3A, SINGLE PHASE INPUT

POWER SUPPLY

 AC 100-240V Wide-range Input

 Width only 65mm

 Efficiency up to 94.3%

 ATEX and IECEx Approved

 Excellent Partial Load Efficiency

 20% Output Power Reserves

 Safe Hiccup

PLUS

Overload Mode

 Easy Fuse Breaking due to High Overload Current

(typ. 45A for 15ms)

 Active Power Factor Correction (PFC)

 Minimal Inrush Current Surge

 Full Power Between -25°C and +60°C

 DC-OK Relay Contact

 Current Sharing Feature for Parallel Use

 3 Year Warranty

1/26

GENERAL DESCRIPTION

The Dimension C-Series are cost optimized power

supplies without compromising quality, reliability and

performance. The C-Series is part of the DIMENSION

power supply family. The most outstanding features of

CPS20.361 are the high efficiency, electronic inrush

current limitation, active PFC, wide operational

temperature range. The small size is achieved by a

synchronous rectification and further technological

design details.

The C-Series includes all the essential basic functions.

The devices have a power reserve of 20% included,

which may even be used continuously at temperatures

up to +45°C. Additionally, the CPS20.361 can deliver

about 3.5 times the nominal output current for 15ms

which helps to trip fuses on faulty output branches.

High immunity to transients and power surges as well as

low electromagnetic emission, a DC-OK relay contact

and a large international approval package for a variety

of applications makes this unit suitable for nearly every

situation.

SHORT-FORM DATA

Output voltage DC 36V

Adjustment range 36 - 42V

Output current 13.3A at 36V, amb <60°C

16A at 36V, amb <45°C

11.4A at 42V, amb <60°C

13.7A at 42V, amb <45°C

Output power 480W ambient <60°C

576W ambient <45°C

Output ripple < 100mVpp 20Hz to 20MHz

AC Input voltage AC 100-240V -15%/+10%

Mains frequency 50-60Hz ±6%

AC Input current 4.36 / 2.33A at 120 / 230Vac

Power factor 0.99 / 0.95 at 120 / 230Vac

AC Inrush current typ. 9 / 7A peak at 120 / 230Vac

Efficiency 93.0 / 94.3% at 120 / 230Vac

Losses 36.1 / 29.0W at 120 / 230Vac

Temperature range -25°C to +70°C operational

Derating *) 12W/°C +60 to +70°C

Hold-up time typ. 26 / 26ms at 120 / 230Vac

Dimensions 65x124x127mm WxHxD

1000g / 2.2lb 1000g / 2.2lb

*) between 100-85Vac see chapter 15

ORDER NUMBERS

Power Supply CPS20.361 36-42V Standard unit

Accessory ZM2.WALL Wall mount bracket

ZM13.SIDE Side mount bracket

YR40.482 Redundancy module

MARKINGS

IND. CONT. E

UL 508

UL 60950-1

Marine

Class I Div 2

IECEx ATEX

II 3G Ex nA nC II T3 Gc

EMC, LVD, RoHS

Apr. 2014 / Rev. 1.4 DS-CPS20.361-EN

All parameters are specified at 36V, 13.3A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless otherwise noted.

www.pulspower.com Phone +49 89 9278 0 Germany

Summary of content (26 pages)

PAGE 1
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series POWER SUPPLY AC 100-240V Wide-range Input Width only 65mm Efficiency up to 94.3% ATEX and IECEx Approved Excellent Partial Load Efficiency 20% Output Power Reserves Safe HiccupPLUS Overload Mode Easy Fuse Breaking due to High Overload Current (typ.
PAGE 2
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series INDEX Page 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Intended Use .......................................................3 Installation Requirements...................................3 AC-Input...............................................................4 DC-Input...............................................................5 Input Inrush Current ...........................................5 Output ..............................
PAGE 3
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 1. INTENDED USE This device is designed for installation in an enclosure and is intended for the general professional use such as in industrial control, office, communication, and instrumentation equipment. Do not use this power supply in equipment, where malfunction may cause severe personal injury or threaten human life. This device is designed for use in hazardous, non-hazardous, ordinary or unclassified locations. 2.
PAGE 4
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 3. AC-INPUT AC input AC input range Allowed voltage L or N to earth Input frequency Turn-on voltage Shut-down voltage nom. min. min. AC 100-240V 100-264Vac 85-100Vac min. max. nom. typ. typ. typ. typ. 264-300Vac 300Vac 50–60Hz 84Vac 39Vac 53Vac 74Vac typ. typ. typ. typ. AC 100V 5.25A 6.33A 0.99 1.5 900ms 90ms AC 120V 4.36A 5.23A 0.99 1.5 850ms 90ms AC 230V 2.33A 2.8A 0.95 1.65 700ms 90ms typ. 200ms 200ms 200ms max.
PAGE 5
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series Fig. 3-3 Input current vs. output current Fig. 3-4 Power factor vs. output current Power Factor, typ. Input Current, typ. 7A 6 5 4 3 2 1 0 1.0 a a) 100Vac b) 120Vac c) 230Vac a, b c 0.95 b 0.9 a) 100Vac b) 120Vac c) 230Vac 0.85 c 0.8 0.75 0 2 4 6 8 10 12 14 16A 0 2 4 6 Output Current at 36V 8 10 12 14 16A Output Current at 36V 4. DC-INPUT Do not operate this power supply with DC-input voltage. 5.
PAGE 6
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 6. OUTPUT Output voltage Adjustment range nom. min. max. typ. typ. typ. max. max. 36V 36-42V 44V****) 36.0V 36.0V 37.5V 10mV 150mV typ. 1500mV Ripple and noise voltage Output current max. nom. nom. nom. nom. typ. 100mVpp 13.3A 16A*) 11.4A 13.7A*) 45A Output power nom. nom. min. max. max. 480W 576W*) cont. current HiccupPLUS mode**) 22A***) 30A***) 9.5A***) min. typ. typ.
PAGE 7
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series Fig. 6-2 Output voltage in “parallel use” mode, typ. Fig. 6-1 Output voltage vs. output current, typ. Output Voltage (Single Use, typ.) 42V 36 24 46V Continuous current Factory setting 30 Output Voltage (Parallel Use, typ.) Adjustment Range Adjustment Range 44V 42V 40V 18 38V Hiccup mode 12 6 0 36V Output Current 0 3 6 Factory setting Output Current 34V 0 9 12 15 18 21 24 27 30A Fig. 6-3 Short-circuit on output, HiccupPLUS mode, typ.
PAGE 8
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 7. HOLD-UP TIME Hold-up Time AC 100V 65ms 54ms 26ms 21ms typ. min. typ. min. Fig. 7-1 Hold-up time vs. input voltage AC 120V 65ms 54ms 26ms 21ms AC 230V 65ms 54ms 26ms 21ms at 36V, 6.7A, see Fig. 7-1 at 36V, 6.7A, see Fig. 7-1 at 36V, 13.3A, see Fig. 7-1 at 36V, 13.3A, see Fig. 7-1 Fig. 7-2 Shut-down behavior, definitions Hold-up Time Zero Transition 80ms 70 60 50 40 30 20 10 0 36V, 6.7A, typ. 36V, 6.7A, min. 36V, 13.3A, typ. 36V, 13.3A, min.
PAGE 9
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 9. EFFICIENCY AND POWER LOSSES Efficiency Average efficiency*) Power losses *) typ. typ. typ. AC 100V 92.4% 91.9% 91.4% AC 120V 93.0% 92.7% 91.8% AC 230V 94.3% 94.1% 93.2% typ. typ. typ. typ. 6.8W 21.0W 39.5W 50.8W 5.8W 20.0W 36.1W 45.4W 2.8W 16.5W 29.0W 36.1W at 36V, 13.3A at 36V, 16A (Power Boost) 25% at 3.3A, 25% at 6.7A, 25% at 10A. 25% at 13.3A at 36V, 0A at 36V, 6.7A (=50%) at 36V, 13.
PAGE 10
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 10.
PAGE 11
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 12. TERMINALS AND WIRING The terminals are IP20 Finger safe constructed and suitable for field- and factory wiring. Input and output screw terminals 0.5-6mm2 0.5-4mm2 AWG20-10 2.8mm (including ferrules) 7mm / 0.28inch 3.5mm slotted or cross-head No 2 1Nm, 9lb.in Type Solid wire Stranded wire American Wire Gauge Max. wire diameter Wire stripping length Screwdriver Recommended tightening torque DC-OK-Signal spring-clamp terminals 0.15-1.5mm2 0.15-1.
PAGE 12
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 13. FRONT SIDE AND USER ELEMENTS Fig. 13-1 Front side A Input Terminals (screw terminals) N, L Line input PE (Protective Earth) input B Output Terminals (screw terminals, two pins per pole) + Positive output – Negative (return) output C Output voltage potentiometer Open the flap to adjust the output voltage. Factory set: 36.
PAGE 13
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 14. EMC The power supply is suitable for applications in industrial environment as well as in residential, commercial and light industry environment without any restrictions. A detailed EMC report is available on request.
PAGE 14
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series The power supply has two converters with two different switching frequencies included. 70kHz to 140kHz PFC converter, input voltage and output power dependent 80kHz to 150kHz Main converter, output power dependent Switching Frequencies Switching frequency 1 Switching frequency 2 15.
PAGE 15
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 16. PROTECTION FEATURES Output protection Output over-voltage protection Degree of protection Penetration protection Over-temperature protection Input transient protection Internal input fuse *) Electronically protected against overload, no-load and short-circuits*) typ. 48.5Vdc In case of an internal power supply defect, a redundant max. 50Vdc circuit limits the maximum output voltage. The output shuts down and automatically attempts to restart.
PAGE 16
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 18. DIELECTRIC STRENGTH The output voltage is floating and has no ohmic connection to the ground. Type and factory tests are conducted by the manufacturer. Field tests may be conducted in the field using the appropriate test equipment which applies the voltage with a slow ramp (2s up and 2s down). Connect all input-terminals together as well as all output poles before conducting the test.
PAGE 17
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 19. APPROVALS EC Declaration of Conformity The CE mark indicates conformance with the - EMC directive 2004/108/EC, - Low-voltage directive (LVD) 2006/95/EC, - RoHS directive 2011/65/EU and the - ATEX directive 94/9/EC (for use in explosive atmospheres). CB Scheme, Information Technology Equipment IEC 60950-1 2nd Edition UL 508 IND. CONT. EQ. UL 60950-1 2nd Edition ANSI / ISA 12.12.
PAGE 18
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 20. PHYSICAL DIMENSIONS AND WEIGHT Weight DIN-Rail Installation Clearances 1000g / 2.2lb Use 35mm DIN-rails according to EN 60715 or EN 50022 with a height of 7.5 or 15mm. The DIN-rail height must be added to the unit depth (127mm) to calculate the total required installation depth. See chapter 2 Fig. 20-1 Front view Fig. 20-2 Side view Apr. 2014 / Rev. 1.4 DS-CPS20.361-EN All parameters are specified at 36V, 13.
PAGE 19
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 21. ACCESSORIES 21.1. ZM2.WALL - WALL MOUNTING BRACKET This bracket is used to mount the power supply onto a flat surface without utilizing a DIN-Rail. 21.2. ZM13.SIDE - SIDE MOUNTING BRACKET This bracket is used to mount DIMENSION units sideways with or without utilizing a DIN-Rail. The two aluminum brackets and the black plastic slider of the unit have to be detached, so that the steel brackets can be mounted.
PAGE 20
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 21.3. REDUNDANCY MODULES YR40.482 – (2x 20A Inputs, 1x 40A output) The YR40.482 is equipped with two input channels, which are individually decoupled by utilizing mosfet technology. Using mosfets instead of diodes reduces the heat generation and the voltage drop between input and output. The YR40.482 does not require an additional auxiliary voltage and is self-powered even in case of a short circuit across the output.
PAGE 21
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 22. APPLICATION NOTES 22.1. PEAK CURRENT CAPABILITY The power supply can deliver peak currents (up to several milliseconds) which are higher than the specified short term currents. This helps to start current demanding loads. Solenoids, contactors and pneumatic modules often have a steady state coil and a pick-up coil.
PAGE 22
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 22.3. EXTERNAL INPUT PROTECTION The unit is tested and approved for branch circuits up to 30A (UL) and 32A (IEC). An external protection is only required if the supplying branch has an ampacity greater than this. Check also local codes and local requirements. In some countries local regulations might apply. If an external fuse is necessary or utilized, minimum requirements need to be considered to avoid nuisance tripping of the circuit breaker.
PAGE 23
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 22.5. PARALLEL USE TO INCREASE OUTPUT POWER CPS20.361 power supplies can be paralleled to increase the output power. The output voltage of all power supplies shall be adjusted to the same value (±100mV) in “Single use” mode with the same load conditions on all units, or the units can be left with the factory settings.
PAGE 24
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 22.7. SERIES OPERATION Unit A AC Power supplies of the same type can be connected in series for higher output voltages. It is possible to connect as many units in series as needed, providing the sum of the output voltage does not exceed 150Vdc. Voltages with a potential above 60Vdc are not SELV any more and can be dangerous. Such voltages must be installed with a protection against touching.
PAGE 25
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 22.10. OPERATION ON TWO PHASES Power Supply 240V +10% max. L1 The power supply can also be used on two-phases of a three-phase-system. Such a phase-to-phase connection is allowed as long as the supplying voltage is below 240V+10%. L3 AC L Fuse L2 internal fuse N PE DC 22.11. USE IN A TIGHTLY SEALED ENCLOSURE When the power supply is installed in a tightly sealed enclosure, the temperature inside the enclosure will be higher than outside.
PAGE 26
CPS20.361 36V, 13.3A, SINGLE PHASE INPUT C-Series 22.12. MOUNTING ORIENTATIONS Mounting orientations other than all terminals on the bottom require a reduction in continuous output power or a limitation in the maximum allowed ambient temperature. The amount of reduction influences the lifetime expectancy of the power supply. Therefore, two different derating curves for continuous operation can be found below: Curve A1 Curve A2 Recommended output current.