800 PSI Pressure Washer Table Of Contents Topic Page # Important Safety Tips, Precautions, Warnings, and Usage Instructions 2-5 Assembly Instructions 6-8 Operating Instructions 9-12 Detergents 12-13 Clean-up and Storage 14-15 Cleaning Tips 16 Technical Data 17 Troubleshooting Tips 18 Limited Warranty 19-2 0 Parts 21-2 3 1
1800 PSI Pressure Washer 1800 PSI Pressure Washer IMPORTANT SAFETY PRECAUTIONS GROUND FAULT CIRCUIT INTERRUPTER (GFCI) WARNING: When using this product, basic precautions should always be followed, including the following: 1. This pressure washer is provided with a ground fault circuit interrupter (GFCI) built into the plug of the power supply cord. This device provides additional protection from the risk of electric shock.
1800 PSI Pressure Washer 5. 6. 7. 8. 9. Read all instructions included with the mask so you are certain the mask will provide the necessary protection against inhaling harmful vapors. Before starting the pressure washer in cold weather, check all of the parts of the equipment and be sure that ice has not formed. Do not store the unit anywhere that the temperature will fall below 0°C (32° F).
1800 PSI Pressure Washer 1800PSI Pressure Washer Step 1 ASSEMBLY INSTRUCTIONS Attach the high pressure hose to the gun. Use a wrench to tighten the fitting. Unpacking The Carton After opening the carton, please remove all parts and check them against the following list of components that are included: E. Two-way Connector F. Water Intake Filter (Pre-Installed) G. Detergent Bottle H. Gun-Shelve A. High Pressure Washer B. Gun C. High Pressure Hose D.
1800 PSI Pressure Washer 1800 PSI Pressure Washer Step 3 Attach the high-pressure hose to the male fitting on the front of the pressure washer. Before attaching the high-pressure hose to the male fitting, remove the plastic cap, which covers fitting before shipping. This plastic cap can be discarded once removed. Hand tighten to av oid leakage.
1800 PSI Pressure Washer 1800 PSI Pressure Washer Automatic On / Off The pressure washer is equipped with an automatic on/off switch.The pressure washer will only run when the power switch is in the ON position and the trigger on the gun is squeezed. When you release the trigger to stop spraying water through the gun, the motor on the pressure washer will automatically shut off. Simply squeeze the trigger again to resume using the washer.
1800 PSI Pressure Washer 1800 PSI Pressure Washer Step 3 ADJUSTING THE PRESSURE To adjust the pressure,proceed as follows: 1. Hold the shaft of the lance in one hand. 2. Turn the grey part of the nozzle clockwise (to “+” end) to obtain the high pressure. 3. Turn the grey part of the nozzle anticlockwise (to “-” end) to obtain the low pressure. Low Pressure Setting Remove the adjustable nozzle to end of “ - ”,put the pressure washer into low-pressure mode.
1800 PSI Pressure Washer 1800 PSI Pressure Washer CLEAN-UP AND STORAGE Winterizing and Long-Term Storage Shutting Down the Pressure Washer FOLLOW ALL OF THE ABOVE SHUT-DOWN PROCEDURES,ADDING THE FOLLOWING STEPS…. WHEN FINISHED USING THE PRESSURE WASHER,FOLLOW THESE STEPS TO SHUT DOWN THE UNIT: Ь Ь Ь Turn the pressure washer to the OFF position. Turn off the water supply. Before disconnecting high-pressure hose connection, point the gun in a safe direction and discharge the high-pressure water.
1800 PSI Pressure Washer 1800 PSI Pressure Washer CLEANING TIPS Maintain a greater rdistance from the cleaning area when using a direct spray. Wipe the surface dry for a polished finish. WARNING: ALWAYS TEST THE SPRAY IN AN AREA FREE AND CLEAR OF PEOPLE AND OBJECTS BEFORE YOU AIMING AT THE INTENDED CLEANING SURFACE. Wood and Vinyl Decks Rinse the area with fresh water. If using detergent, fill the detergent reservoir and apply to the area being cleaned at low pressure.
1800 PSI Pressure Washer TROUBLESHOOTING TIPS 1800PSI PRESSURE WASHER WHEN THE SWITCH IS IN THE “I” POSITION THE MACHINE WILL NOT START LIMITED WARRANTY PROBABLE CAUSE SOLUTION Electrical socket is faulty Voltage is inadequate GFCI trips Power cord is not plugged in Check plug, socket, and fuses Check that the voltage is adequate Reset / Try another outlet Plug in power cord THE PUMP DOES NOT REACH ADEQUATE PRESSURE OR FLUCTUATES PROBABLE CAUSE SOLUTION Water Intake Filter is clogged Pump is draw
1800PSI PRESSURE WASHER LIMITED WARRANTY (cont’d) 1800PSI PRESSURE WASHER EXPLODED VIEW THIS WARRANTY DOES NOT COVER: Merchandise sold as reconditioned, used as rental equipment, or floor or display models.
1800PSI PRESSURE WASHER 1800PSI PRESSURE WASHER PARTS LISTING PARTS LISTING Part No Description PWE1800-01 PWE1800-02 PWE1800-03 PWE1800-04 PWE1800-05 PWE1800-06 PWE1800-07 PWE1800-08 PWE1800-09 PWE1800-10 PWE1800-11 PWE1800-12 PWE1800-13 PWE1800-14 PWE1800-15 PWE1800-16 PWE1800-17 PWE1800-18 PWE1800-19 PWE1800-20 PWE1800-21 PWE1800-22 PWE1800-23 PWE1800-24 PWE1800-25 PWE1800-26 PWE1800-27 PWE1800-28 PWE1800-29 PWE1800-30 Rubber Stopper Switch Knob Case(Front) Outlet Cover Screw Switch Case(Front) Swi
