User Instructions

ManualsBrandsPulsar ManualsARAD enclosuresRACK 2U/270mm universal enclosurefor RACK 19" cabinets

INSTALLATION GUIDE

ENGLISH

Code: ARAD2S

Name: RACK 2U/270mm universal enclosure

for RACK 19" cabinets

Metallic enclosure for RACK cabinet: CCTV, KD, SSWiN, RTV, LAN

IM ARAD2S

Edition: 1 from 20.03.2017

Supersedes: ------------

1. Intended use:

Due to its design, the ARAD2S enclosure is intended for mounting inside RACK 19'' cabinets - 450mm depth. This

general-purpose enclosure may serve as an auxiliary element for integrating CCTV, AC, I&HAS, RTV, LAN systems in

RACK 19'' cabinets. It is intended for mounting alarm control panels, AC controllers, power supply units, batteries, etc.

2. Description

The enclosure is equipped with a mounting plate for mounting electronics/transformers/power supply units. The

enclosure can accommodate a 7Ah/12V battery and it features tampering protection (against unwanted opening). To

enable leading cables into the enclosure, one can buy a cable protection conduit of any length and a cable gland. The

conduits and the cable glands are available at the following codes:

1) ARAP16P – cable gland, inside diameter 16 mm – connection between the protection conduit and the enclosure

2) ARAP21P – cable gland, inside diameter 21 mm – connection between the protection conduit and the enclosure

3) MM019 – cable protection conduit , inside diameter 16 mm

4) MM020 – cable protection conduit, inside diameter 21 mm

The ARAD2S enclosure has a space for up to 2x ARAP16P and 3x ARAP21P cable glands.

Optionally, ARAW45 fans can be mounted. They trigger airflow inside the enclosure after exceeding 45

C. One

enclosure can accommodate max. two fan units in the rear part of the enclosure.

Summary of content (4 pages)

PAGE 1
INSTALLATION GUIDE ENGLISH Code: ARAD2S Name: RACK 2U/270mm universal enclosure for RACK 19" cabinets Metallic enclosure for RACK cabinet: CCTV, KD, SSWiN, RTV, LAN IM ARAD2S Edition: 1 from 20.03.2017 Supersedes: ------------ EN 1. Intended use: Due to its design, the ARAD2S enclosure is intended for mounting inside RACK 19'' cabinets - 450mm depth. This general-purpose enclosure may serve as an auxiliary element for integrating CCTV, AC, I&HAS, RTV, LAN systems in RACK 19'' cabinets.
PAGE 2
Dimensions of the mounting plate 3. Assembling instructions: The ARAD2S enclosure can be mounted in two ways: 1. Mounting without the ARAS450 rails, no extension slide, the front part is the load-bearing part of the enclosure. This method of installation is dedicated for economic versions with a load capacity of up to 5 kg.
PAGE 3
2. Mounting with the ARAS450 rails - full extension slide of the RACK cabinet, rails of the ARAS450 series are the load-bearing part of the enclosure. Dedicated for up to 30kg load. 2.1. Mount cage nuts for M6 screws in the RACK cabinet, as shown in Figure below, and mount the ARAS450 rails. Make sure that the rail is correctly mounted horizontally and its length between the front and rear RACK profile is properly adjusted. 2.2.
PAGE 4
The ARAW45 fan Cable glands and protection tubes Wires can be introduced in three ways: a) - Through rubber grommets, b) - Using the MM019/MM020 protection tubes, c) - Using the MM019/MM020 protection tubes and the ARAP16P/ARAP21P cable glands. 5. Specifications SPECIFICATIONS Fitting battery 7Ah/12V Tampering protection 1x – against unwanted opening of the enclosure Max. load of TAMPER output Enclosure: IP Operation temperature Relative humidity RH – max.