Operation Manual

11
on actual position).
 Automatic exiting the menu takes place after more than 10 seconds of
inactivity (no navigation).
Status bar
Status bar in the bottom part of the display shows information as follows:
 Number of weapon choice (1,2,3):
 Digital zoom (from 1.1x to 2.0x with 0.1x increment): x2.0
 Automatic shutoff is on:
 IR Illuminator is on (with power level 1;2;3):
 “SumLight™” function on/off:
 “Automatic contrast” function on/off:
 Running time:
 Battery charge level or connected external battery:
The riflescope has three menus:
M1 – menu 1 (main menu);
М2 – menu 2 (additional menu);
M3 – menu 3 (rangefinder menu).
Active menu is highlighted with a frame . To switch to another menu, rotate the
controller and move the cursor (the frame will be flashing), press controller
button (7).
Menu М1 (main menu) includes:
 “Sum Light™” ON/OFF
 “Automatic contrast” ON/OFF
 Weapon selection (1;2;3)
 Selection of preloaded reticle
 Reticle colour selection
 Weapon tilt indicator ON/OFF
 Brightness control of onscreen symbols
(menu and status bar)
Menu М2 (additional menu) includes:
 One shot zeroing
 “Freeze” zeroing
 Selection/disable of video output signal
 Clock setup
 Remote control activation
 Automatic shutoff ON/OFF
 Assignment of the functional button (8) -
“SumLight™”, “Automatic contrast”, “Reticle
colour selection”
Menu М3 (rangefinder menu) includes:
 “THD” function (selection of true
horizontal distance) THD
 Choice of rangefinding indicator
 “AoE” function (angle of elevation
measurement) AoE
 Switching between units of measurement
(metres/yards)
 Return to default settings
Aut
M
1
M
Aut
?
M/Y
DESCRIPTION OF MENU OPTIONS
Menu М1 options
“SumLight™” function
SumLight™ function substantially increases sensitivity of the CCD array thus
enabling observation in low light without using the IR Illuminator. When using the
unit at a sufficient level of night illumination, the Sum Light™ function can be
deactivated manually using the menu or the functional button (8).
 Rotate the controller (7) to select “O ress of the controller n” or “Off”. Short p
button confirms choice.
 Icon “SumLight™” (on or off) is shown the status bar. on
Attention! Please note that higher sensitivity causes an increased noise level in
the picture, lower frame rate; image slows down, if the riflescope is rapidly
moved from one side to the other, the picture may be blurred for a moment.
Neither of these effects is a flaw of the unit. After the SumLight™ Signal
Processing Program is activated, light dots (pixels) may appear in the field of
view which is explained by operation peculiarities of this function. This is not a
defect either.
“Automatic contrast” function
 Rotate the controller (7) to select “On” or “Off”.
 Short press of the controller button confirms choice.
 Icon “SumLight™” (on or off) is shown the status bar.on
Weapon selection (1,2,3)
This menu option allows selection of three variants of zeroing parameters for
various types of weapons or for various distances. Also this option allows you to
save three types of reticle for each weapon.
 To select option, press controller button and select number out of the list
(1; 2; 3).
 Confirm your choice by a short press of the controller button.
 Number of the selected variant of the weapon to use is shown in the status bar
in the lower portion of the display.
Note: Originally the reticle for all the three variants is located in the display
centre (coordinates X=0;Y=0). Further on, each type of weapon (distance)
requires individual zeroing.
Selection of preloaded reticle
This menu option allows selection of one of the 13 preloaded reticles. Menu
option shows number of the reticle.
 To select option, press controller button and select reticle number out of the
list. Corresponding reticle will be shown on the display.
 Confirm your choice by a short press of the controller button.
 List and full description of the reticles can be found at www.pulsar-nv.com
IMPORTANT! Please note that due to peculiarities of OLED display technology,
when switching between various reticles, you may notice on the riflescope's
display residual “ghost image” of the previous reticle. The “ghost image” looks like
semitransparent white lines. The image may appear if a new reticle does not
contain elements (such as lines, circles, bars etc.) of the previous reticle. After a
while the “ghost image” becomes less noticeable. We do not take any
responsibility for the claims in connection with “ghost image” arisen due to multiple
change of reticles.
10