Interface ETHERNET v.1.1 CODE: INTE EN* Edition: 8 from 27.11.2019 Supercedes edition: 7 from 25.01.
www.pulsar.pl INTE TABLE OF CONTENTS 1. General description. ............................................................................................................................. 3 2. Components arrangement. .................................................................................................................. 3 3. Installation............................................................................................................................................. 4 4.
www.pulsar.pl INTE Features: connection to the ETHERNET network via the RJ45 connector Permission of the Scientific and Research Centre for Fire Protection - National Research Institute for use with power supplies of the EN54 series in fire alarm systems compliance with the IEEE 802.
www.pulsar.pl INTE 3. Installation. The Ethernet interface should be mounted inside the enclosure of the PSU. The connection between the power supply with Ethernet interface and the router should be made with a twisted pair with RJ45 connectors. The role of the access point controlling the data flow is done by a router connected to a PC via Ethernet cable. Fig.2. Schematic diagram of Ethernet network communication. Interface installation: 1. Install the Ethernet interface in the enclosure of the PSU. 2.
www.pulsar.pl INTE 4. Ethernet interface configuration. 4.1 Introductory information. Ethernet interface parameters can be configured to adapt to the actual operation. Configuration is done using the „PowerConfig” program. The „PowerConfig” program is available on: http://www.pulsar.pl/pliki/PowerConfig.exe A newly purchased Ethernet interface is supplied in basic configuration (factory settings) which is not adapted for correct operation of the system.
www.pulsar.pl INTE 4.3 STEP 2 – Network interface search. For proper IP address change, it is recommended to turn off the firewall of the antivirus program for the time of configuration process. Run the „ PowerConfig” program. Make sure that the INTE Ethernet module is powered and connected to the router via a network cable. In the "Module type" field choose the "Ethernet" and the search method. When the "UDP broadcast" is selected, the program will search for all the interfaces on the subnet.
www.pulsar.pl INTE 4.4 STEP 3 – The TCP/IP Network settings. Press the “Settings" button from the menu on the left side of the PowerConfig program window. A window will be displayed in the right part of the screen. Choose the "Network TCP / IP” from the top tab menu. This window allows setting the IP address for Ethernet communication. Fig. 6. The TCP/IP Network settings.
www.pulsar.pl INTE 4.5 STEP 4 – Setting the serial port parameters – the “Serial port”. In the "Serial port" tab, set the parameters responsible for the communication between Ethernet interface and the PSU as shown in the picture below. Fig. 7. Setting the serial port communication parameters.
www.pulsar.pl INTE 5. PSU configuration. 5.1 Configuration of power supplies of PSBEN series with LCD display. The PSU is fitted with LCD display, which enables setting the communication parameters of the serial port from the LCD panel. To enter the setup mode, press the „SET” button from the main screen.
www.pulsar.pl INTE 5.2 Configuration of power supplies of PSBEN series with LED display. The PSU is fitted with LED display, which enables setting the communication parameters of the serial port from the LED panel. To enter the setup mode, simultaneously press the „<,>” rightmost and leftmost buttons on the LED panel.
www.pulsar.pl INTE 5.3 Configuration of power supplies of EN54 series with LCD display The PSU is fitted with LCD display, which enables setting the communication parameters of the serial port from the LCD panel. To enter the setup mode, press the „SET” button from the main screen.
www.pulsar.pl INTE 5.4 Configuration of power supplies of EN54 series with LED display The PSU is fitted with LED display, which enables setting the communication parameters of the serial port from the LED panel. To enter the setup mode, simultaneously press the „<,>” rightmost and leftmost buttons on the LED panel.
www.pulsar.pl INTE 6. Configuring the connection in PowerSecurity program. For further configuration, the PowerSecurity program is required. The program is available on: http://www.pulsar.pl/pliki/PowerSecurity.exe It is an executable file, which does not require installation. 1) Run the PowerSecurity.exe. 2) Choose the Power Supplies > New Power Supply option from the menu bar. The “Configuration of connection” window, that allows configuring the settings, will be displayed. Fig. 8.
www.pulsar.pl INTE remote desktop of PSU PSBEN remote desktop of PSU EN54 menu bar manager window Fig. 9. Remote desktop windows of the power supplies: PSBEN (left) and EN54 (right). More information on the "PowerSecurity" program can be found in the manual which can be downloaded at: http://www.pulsar.pl/pl/opisy/PowerSecurity.pdf 7. Technical parameters.
