User Instructions

ManualsBrandsPulsar ManualsEquipment for HD camerasOperating automation module PSB 13,8V

MPSB12

v.1.1

PSB 13,8V automation module

Edition: 5 from 06.08.2018

Supersedes the edition: 4 from 01.06.2016

EN*

Features:

 battery status control

 works with PSBxx, HPSBxx 13,8V power

supply units

 LED indication

 EPS technical output indicating AC power

collapse – OC and relay type

 PSU technical output indicating power supply

module’s failure – OC and relay type

 LoB technical output indicating low battery

voltage – OC and relay type

 warranty – 2 year from the production date

1. Technical description.

1.1 General description

MPSB12 automation module is intended for indicating the operating status of buffer power supplies PSB 13,8V

type. The PCB board features LEDs that indicate PSU operating status (presence of AC voltage, presence of DC

voltage, battery voltage). The module is also equipped with technical outputs of OC and relay type: AC power loss,

PSU failure, low battery voltage.

1.2. Description of the module’s components and connectors (fig1, tab.1)

Table 1

Element

no.

Description

[1]

LED indicating presence of 230VAC voltage

[2]

LED indicating presence of DC voltage at the PSU output

[3]

LED indicating correct battery voltage

[4]

EPS - technical output indicating AC absence – relay type

[5]

PSU - output indicating DC absence/PSU failure - relay type

[6]

LoB - output indicating low battery voltage - relay type

[7]

EPS - technical output indicating AC absence – OC type

[8]

PSU - output indicating DC absence/PSU failure - OC type

[9]

LoB - output indicating low battery voltage - OC type

[10]

+BAT- battery connector

[11]

Indication connector

[12]

+V –13,8V supply

Fig. 1. The view of the module.

Summary of content (4 pages)

PAGE 1
MPSB12 v.1.1 PSB 13,8V automation module Edition: 5 from 06.08.2018 Supersedes the edition: 4 from 01.06.2016 EN* PL Features:      battery status control works with PSBxx, HPSBxx 13,8V power supply units LED indication EPS technical output indicating AC power collapse – OC and relay type   PSU technical output indicating power supply module’s failure – OC and relay type LoB technical output indicating low battery voltage – OC and relay type warranty – 2 year from the production date 1.
PAGE 2
1.3 Specifications: - electrical specifications (tab.2) - mechanical specifications (tab.3) Table 2. Supply voltage Current consumption Voltage of low battery indication Technical outputs: - EPS; output indicating AC power failure 13,8V DC 60mA max. U<11,5V +/- 3% - relay type: 1A@ 30VDC/50VAC, time lag: approx. 10s. CAUTION! In Fig.2. the contact set in the potential-free status corresponds to a state with no AC power (AC power failure). - OC type, 50mA max.
PAGE 3
2.1. Requirements. The module is to be mounted by a qualified installer, holding relevant permits and licenses (applicable and required for a given country) for 230V/AC interference and low-voltage installations. The unit should be mounted in confined spaces, in accordance with the 2nd environmental class, with normal relative humidity (RH=90% maximum, without condensation) and temperature from -10°C to +40°C.
PAGE 4
3. Maintenance. Any and all maintenance operations may be performed following the disconnection of the PSU from the power supply network. The PSU does not require performing any specific maintenance measures. However, in case of a thick dust layer, clean the PSU with compressed air. WEEE MARK According to the EU WEE Directive – It is required not to dispose of electric or electronic waste as unsorted municipal waste and to collect such WEEE separately. Pulsar Siedlec 150, 32-744 Łapczyca, Poland Tel.