7500 7500 1-866-591-8921
The generator is a potential source of electrical shock if misused. Do not expose the generator to moisture, rain or snow. Do not let the generator get wet, and do not operate it with wet hands. These labels warn you of potential hazards that can cause serious injury. Read them carefully.
SAFETY INFORMATION Read and understand this instruction manual before operating your generator. You can help prevent accidents by being familiar with your generator’s controls, and by observing safe operating procedures. Operator Responsibility Know how to stop the generator quickly in case of emergency. Understand the use of all generator controls, output receptacles, and connections. Do not let children operate the generator without parental supervision.
TABLE OF CONTENTS SAFETY INFORMATION ......................................................................................................... 1 GENERATOR COMPONENTS .................................................................................................4 WATTAGE REFERENCE CHART…………………………………………………………………...7 PRE-OPERATION CHECK………………………………………………………………………......8 STARTING THE GENERATOR ...................................................................................................
Fuel tank cap Fuel tank Frame Control panel Air cleaner Wheel Handle Fuel valve Recoil starter Dipstick Engine key Battery Oil drain plug Thermal protector Thermal protector Thermal protector Runing time meter Thermal protector 120/240AC Receptacles 120AC Receptacles 120AC Receptacles DC terminal 4
Engine Key To start and stop the engine. Key position: OFF: To stop the engine. Key can be removed / inserted ON: To run the engine after starting. START: To start the engine by operating the starter motor (only for electric start) Do not turn the key switch to START position when the engine is running to prevent damage of starting motor. Recoil Starter To start the engine, pull the starter grip lightly until resistance is felt, then pull briskly.
Change the Voltage Selector Switch after turning the AC circuit breaker to OFF. The generator may be damaged. Ground Terminal The generator ground terminal is connected to the frame of the generator, the metal non-current-carrying parts of the generator, and the ground terminals of each receptacle. DC Receptacle The DC receptacle may ONLY be used for charging 12 volt automotive type batteries.
WATTAGE REFERENCE CHART Electric equipment, especially engines produce strong current when being started. The table below offers references when you connect those installations to generator. Tool or Appliance Rated* (Running) Watts Additional Surge (Starting) Watts Light Bulb-75 watt 75 - Deep Freezer 500 500 Sump Pump 800 1200 Refrigerator/Freezer-18 Cu. Ft.
Wheel Kit Installation 1. Fit two wheels and two handles to the generator with lolts and nuts. 2. Before starting generator, press the lock system of wheels and handles to prevent displacement during the work time. PRE-OPERATION CHECK Engine Oil Engine oil is a major factor affecting engine performance and service life. Non-detergent and 2-stroke engine oils will damage the engine and are not recommended. Check the oil level BEFORE EACH USE with the generator on a level surface and the engine stopped.
Gasoline is highly flammable and explosive, and you can be burned or seriously injured when refueling. ● Stop engine and keep heat, sparks, and flame away. ● Refuel only outdoors. ● Wipe up spills immediately. Use unleaded gasoline with a pump octane rating of 86 or higher. This engine is certified to operate on unleaded gasoline. Unleaded gasoline produces fewer engine and spark plug deposits and extends exhaust system life. Never use stale or contaminated gasoline or an oil/gasoline mixture.
OPERATING INSTRUCTIONS Connections to a Building Electrical System Connections for standby power to a building electrical system must be made by a qualified electrician. The connection must isolate the generator power from utility power, and must comply with all applicable laws and electrical codes. A transfer switch, which isolates generator power from utility power, is prerequisite.
modifications to the carburetor. If you always operate your generator at altitudes above 5,000 feet (1,500 meters), have your dealer perform this carburetor modification. This engine, when operated at high altitude with the carburetor modifications for high altitude use, will meet each emission standard throughout its useful life. Even with carburetor modification, engine horsepower will decrease about 3.5% for each 1,000-foot (300-meter) increase in altitude.
REGULAR SERVICE PERIOD（2） Before each ITEM Performed at every indicated month or use operating hour interval, whichever comes first. Check ○ ● Engine oil Change Check ○ ● Air cleaner Clean Clean ● Sediment cup Clean-Adjust ● Spark plug Replace Clean ● Spark arrester Check-Adjust ● Idle speed Check-Adjust ● Valve clearance Combustion Clean ● chamber Clean ● Fuel tank and filter Check ● Fuel tube First month or 20 Hrs. Every3 months or 50 Hrs. ○ Every6 months or 100 Hrs.
Never run the generator without the air filter. Rapid engine wear will result. 1 Unsnap the air cleaner cover clips, remove the air cleaner cover, and remove the element. 2 Wash the air cleaner element in a solution of household detergent and warm water, then rinse thoroughly, or wash in nonflammable or high flashpoint solvent. Allow the air cleaner element to dry thoroughly. 3 Soak the air cleaner element in clean engine oil and squeeze out the excess oil.
The gap should be: 0.028 0.031 in (0.70 0.80 mm) 6 Check that the spark plug washer is in good condition, and thread the spark plug in by hand to prevent cross-threading. 7 After the spark plug is seated, tighten with a spark plug wrench to compress the washer. －If installing a new spark plug, tighten 1/2 turn after the spark plug seats to compress the washer. If reinstalling a used spark plug, tighten 1/8 －1/4 turn after the spark plug seats to compress the washer.
Battery use: Aim remote start the gasoline engine (distance between more than 50m). Requirement: 1. The specification of battery recommended: 12V,9AH 2. Do not connect the anode and negative pole erroneously, when use the battery. 3. The battery need to be injected electrolyte before use. 4. The height of electrolyte need to be inspected each month. when the level is low, please inject distilled water or pure water between upper and low level. 5.The battery need to be clean.
TROUBLESHOOTING Note: Troubleshooting problems may have similar causes and solutions. PROBLEM The engine will not start No electricity at the AC receptacles POSSIBLE CAUSE SOLUTION Is there fuel in the tank? Refill the fuel tank. Is there enough oil in the engine? Add the recommended oil. Is the spark plug in good condition? Readjust gap and dry the spark plug. Replace it if necessary. Is the fuel reaching the carburetor? Clean the fuel sediment cup.
17
Breaker R W ControlBoxDiagram R R GNAJ W W DCcoil1 L14-30R Breaker Bl YG 20A 20A 3in1 DigitalMeter L6-30R 5-20R 5-20R Bl GrQVR1.5mm LBQVR1.5mm Bl BlQVR1.5mm LBQVR1.5mm + 8A 2510 RQVR0.5mm OQVR0.5mm BuQVR0.5mm BlW QVR0.5mm BrQVR0.5mm DCcoil2 BrRQVR0.5mm Bl W R Bu Bu RQVR0.5mm BuQVR0.5mm BuQVR0.5mm R QVR0.5mm Bl Black O Orange W QVR0.5mm Br Brown BrR BrownRed Bu Blue LB LightBlue Gr Gray Bl Black R Red W White YG YellowGreen BlW A V R Br QVR0.5mm O QVR0.
Intelligence Protect Switch 1. When the load reaches the rated power, indicator light turns green. 2. When the load reaches the maximum power, indicator light runs red, the buzzer alarms. 3. When the load exceeds the maximum power for 1 minute, it automatically switches off the output. 4. Press the switch, the generator set works again. Automatic Generator System (AGS) After installation, be sure the machine is not overloaded.
