Introduction This rotary-blade, walk-behind loon mower is intended to be used by residential homeowners or professional, hired operators. It is designed primarily for cutting grass on well -maintained lawns on residential or commercial properties. It is not designed for cutting brush or for agricultural uses. Read this information carefully to meal how to paratroops and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely.
» Do not operate this making while under the Influences of wholesale or drugs. « Never operate mower in wet grass. Always be sure of your footing; walk; never run. » Disengages the drives system, if so skipped, before starting the engine. « If the machine should sitar to vibrate abnormally, sip the engine and check for the cause immediately. Vibration is generally a waning of trouble. « Always wear eye protection when operating machine. « Lightning can cause severe injury or death.
Product Specification Component Specification Rated Speed 2800RPM Displacement 180cc Curling Width 20" Height Adjustment -3 Wheels 7" Front 11" Rear Machine Weight 60 lbs Safety & Instruction Decals important: Safely & instruction decals are located near areas of potential DANGER. Replace damaged decals. 1. WARNING: Read the Operator's Manual 2. Thrown Object Hazard: Sap bystanders a safe distance from the mower. 3.
Product Overview Figure 4 1. Alr Filter 2. Fug Tank Cap Fill/ Dipstick 4. Height Adjustment Checking the Engine Qil Level! §. Handle Loosening Knob service Interval: Before sate use. 1. Remove dipstick, wipe it clean, and fully re-insert it . check to ses if oll is sadden by the oll mark that is left Q Operation the dipstick. (Figure 6) Attachmenis/Accessories A selection of Pulsar approved attachments and accessories are available for use with the machine to Enhance and expand its capabilities.
Cutting Height Adjustment Adjusting the cutting height may bring you Into contact with the moving blade, causing serious injury. » §top the engine and Walt for all the moving parts to stop. « Do not put your fingers under the housing when adjusting the curling alight, Do not excised cutting height adjustment imitated location, or it will causing serious injury or death. if ths engine has bun running, the muffler will ba hot ants can severely burn you. Esp sway from the hot muffler.
Mulching the Clippings Your mower comes mulch ready. f you have a grass catcher plazas removal it before mooching. Bagging the Clippings (Not included) Use the grass catcher when you want to collect grass and leaf clippings from the lawn. & wom grass catcher could allow small stones and other similar debris {0 be thrown in the operator’s of bystander's direction and result in curious personal injury or death to the operator or bystanders, Thea blade is sharp.
Spark Plug Maintenance 1. Nee the engine has cocked, remove the spark plug wire. 2. Remove the spark plug using a spark plug wrench. 3. Clean the spark plug with a wire brush (not supplied). 4. Using a feeler gauge set the gap to 0.75mm. 5. install the spark plug carefully by hand, to avoid cross-threading. &. After the spark plug is seated, tighten with the spark plug wrench to compress the washer. Maintenance Note: Determine the left and right sides of the machine from the normal operating position.
Replacing the Alr Filter Service interval: Every 25 Hours 1. Turn lat to open cap of the air filter. (Figure 12} {Figure 12} 2. Replace the air 13) (Figure 13) 3. Align cap, three dabs, with baize. Crass down and fum right to 14} {Figure 14) Changing the Engine O#f Services Interval: After the first 5 hours. Yearly. Chang the engine oil flora the firer § operating hours sangs it yearly thereafter. Run the engine a few minutes before changing the ofl. Warm ofl flows better and caches more contaminants. 1.
7. install new balds with all mounting hardware; tighten blade bull by looming 165}, Figure 16 important: Position the curved ends of the blade 1o point up toward the mower deck. 8.Use a torque wrench fo tighten the blade belt to 30-381tb (40-50 N-m). Important: Correct blade hub bolt torque is very important. Use proper tools onion Cleaning the Mower Service Interval: Before each use or daily /\ WARNING The mower may dislodge material from under the mower housing. « Wear eye protection.
WARRANTY PULSAR PRODUCTS Milked 1 Year Warranty: From the date of original purchase, Pulsar Products Inc. warrants fo the original purchase, that each Lawn Mower sold, shall be free from defect in malarial and workmanship for a period of 1-year on all components. Pulsar Products inc., at s discretion, agrees to repair or replace any defective part that upon examination, inspection, and testing by a Pulsar Products Inc. authorized service dealer, is found to be detective within the original warranty period.
WARRANTY What this Warranty Does Not Cover: » Normal wear: This warranty excludes normal wear smells unless under normal use, the original equipment is defective in material or workmanship and needs fo be replaced price fo the first replacement interval, » Maintenance: This warranty does not apply fo routine maintenance and does not cover any adjustments or repairs not performed by an authorized repair facility.
