(E.F.S.G.I.P.) ANALOGUE TYPE Series PJU (Cal.
(E.S.) ES – A22 ANALOGUE TYPE Series PJU & PJN (Cal.
(E.F.) EF – A22 ANALOGUE TYPE Series PJU (Cal.
PULSAR ANALOGUE QUARTZ WITH CHRONOGRAPH FUNCTION DISPLAYS AND CROWN OPERATION There are two buttons and a crown as indicated in the illustration below. Cal. V656, V657 FEATURES This is a multi-display analogue watch featuring a chronograph function. The measured time is indicated by the small chronograph hands that move independently of the center hands. ■ TIME Cal. V656 : Hour, minute, second and 24-hour hands. Cal. V657 : Hour, minute and second hands. ■ CALENDAR (for Cal.
ADJUSTING THE CHRONOGRAPH HAND POSITION [Cal. V657] Chronograph 1/10second hand Minute hand A Hour hand a b c Crown Chronograph minute hand B Before setting the time, be sure to check if the chronograph hands are in the “0” position when the chronograph is reset. Note: The “0” position of the chronograph 1/10 second hand differs depending on the models. * Some models have the “0” position of the chronograph 1/10 second hand at 3 and 9 o’clock sides of the small dial.
[Cal. V656] TIME/CALENDAR SETTING [Cal. V657] A N o t e : While the crown is at the extended position (Cal. V656) or at the second click (Cal. V657), do not press any button. Otherwise, the chronograph hands will move. To reset them to the “0” position, refer to“ADJUSTING THE CHRONOGRAPH HAND POSITION”. A [Cal. V656] B Crown ( Extended position ) B [Cal. V657] Minute hand Second hand Crown ( Second click ) 1. Pull out the crown all the way. 2.
Time setting for Cal. V656 1. Pull out the crown when the second hand is at the 12 o’clock position. The second hand will stop on the spot. 2. Turn the crown clockwise or counterclockwise to set the hour, minute and 24-hour hands to the desired time. * When setting the hour hand, be sure to check that the 24hour hand is set properly. 3. Push the crown back in to the normal position in accordance with a time signal. 3.
CHRONOGRAPH The chronograph can measure up to 60 minutes in 1/10 seconds. The measured time is indicated by the small chronograph hands that move independently of the center hands. Note: While the chronograph is counting, do not pull out the crown to set the time. Otherwise, the chronograph operation cannot be made. How to read the hands Ex.) Elapsed time measured is 15 minutes and 10.
To stop : To reset to “0” : Press “A”. Press “B”. 3. Split time measurement To start : To measure split time : To release split time : To stop : To reset to “0” : Press “A”. Press “B”. Press “B”. Press “A”. Press “B”. NECESSARY OPERATION AFTER BATTERY CHANGE When the battery is replaced, the time information stored in the built-in IC and the time indicated by the hands do not correspond with each other.
1. Pull out the crown all the way. 2. Keep “A” and “B” pressed at the same time for 2 seconds, and then release the buttons. The chronograph second hand turns half a circle counterclockwise and then returns where it was. The chronograph 1/10 second hand turns a full circle clockwise and stops. 3. P r e s s “ A ” r e p e a t e d l y t o r e s e t t h e c h r o n o g r a p h 1 / 1 0 s e c o n d hand to the “0” position. Press “B” repeatedly to reset the chronograph second and minute hands to the “0” position.
W a t e r r e s i s t a n t ( 1 0 0 m / 1 0 B A R , 2 0 0 m / 2 0 B A R ) : These watches are suitable for swimming or skin diving (without heavy breathing apparatus), but not for scuba diving. If the watch is exposed to salt water, rinse it in fresh water and then wipe it thoroughly dry. Do not press any buttons or turn the crown when the watch is wet. N o n - w a t e r r e s i s t a n t : Care should be taken not to get your watch wet as water may damage the movement.
