CAL.
MODE CHANGE With each press, the mode changes in the following order: ➡ English URL MEMO ➡ ALARM ➡ TIMER ➡ MESSAGE ➡ TIME/ CALENDAR A B ➡ A STOPWATCH B ➡ ➡ [horizontal] B 2 [vertical] With each press in TIME/CALENDAR mode, the display changes between horizontal and vertical alternately.
TIME/CALENDAR MODE TIME/CALENDAR SETTING B Clockwise turning: Digits decrease. E Return to TIME/CALENDAR mode. ➾ 12-/24-hour indication Date ➾ ▲ ▲ B Turn clockwise or counterclockwise to set the flashing digits. Selection of the digits Seconds ➾ Minutes ➾ Hour ➾ E Press to select the digits to be adjusted. ➾ ▲ ▲ E Press for 2 to 3 seconds to show TIME/CALENDAR SETTING display. Year ➾ B English Counterclockwise turning: Digits increase.
SHOWING CALENDAR DISPLAY E Turn clockwise or counterclockwise to show CALENDAR display instead of TIME display. English TURNING ON/OFF OF HOURLY TIME SIGNAL AND BUTTON OPERATION CONFIRMATION SOUND C Hourly time signal mark 4 C With each press, the hourly time signal and sound for button operation confirmation are alternately switched on and off.
DISPLAYING MESSAGES E E Press to show a message. * A message appears and scrolls three times. ● The watch also displays a message automatically every 10 minutes. The message scrolls three times. English • If you have recorded any messages, such message alone will be displayed. • If no message is recorded, the built-in messages will be displayed one by one with each press of button E. • If you have recorded any messages, such message alone will be displayed.
STOPWATCH MODE ● The stopwatch measures up to 10 hours in 1/100 second increments. C Split / Split release / Reset English E (Press the button.
TIMER MODE ● Two types of timer are available: 10-channel preset timer and adjustable timer. ● The adjustable timer can be set up to 9 hours and 59 minutes in minute increments. PRESET TIMER SETTING B E English Clockwise turning: Digits decrease. Counterclockwise turning: Digits increase. Turn clockwise or counterclockwise to select the preset time. Selection of the preset time/adjustable timer ⇔ 1 min. ⇔ 2 min. ⇔ 3 min. ⇔ 4 min. ⇔ 5 min. ⇔ 10 min. ⇔ E Adjustable timer ⇔ 30 min. ⇔ 25 min.
ADJUSTABLE TIMER SETTING E ▲ B ▲ Press for 2 to 3 seconds to show ADJUSTABLE TIMER SETTING display. Press to select the digits to be adjusted (hour/minutes). ▲ E Turn clockwise or counterclockwise to set the flashing digits. ▲ English ▲ E Turn clockwise or counterclockwise to select the adjustable timer. (See the previous page) B Return to TIMER mode. TIMER OPERATION C Reset E 8 (Press the button.
ALARM MODE ● Regular alarm and 3-channel single-time alarm are available. ● Each of the three single-time alarms can be set to ring only once at the designated time. As it rings, it is automatically disengaged. ALARM TIME SETTING B E English Clockwise turning: Digits decrease. Counterclockwise turning: Digits increase. Turn clockwise or counterclockwise to select the desired alarm channel.
B Press for 2 to 3 seconds to show ALARM SETTING display. ▲ ▲ E Press to select the digits to be adjusted (hour/minutes). ▲ E Turn clockwise or counterclockwise to set the flashing digits. English ▲ B Return to ALARM mode. * “ON” mark appears and the alarm is automatically engaged. ALARM ENGAGEMENT/DISENGAGEMENT ● The alarms can be engaged and disengaged independently of one another. C E 10 ▲ E C Turn clockwise or counterclockwise to select the desired alarm channel.
URL MEMO MODE ● Up to 100 URL memos such as Internet homepage address and electronic mail address can be registered for display. ● Up to 60 characters can be entered for each URL memo. ● The residual memory capacity can also be indicated.
ENTERING A NEW DATA B Press for 2 to 3 seconds to show MENU display. ▲ Turn clockwise or counterclockwise to select the data entry operation (NEW). E Deletion of one data DEL ⇔ Deletion of entire data CLR ➾ ⇔ ➾ Selection of the operation New entry Correction ⇔ NEW EDIT ▲ English E While “NEW” is flashing, press to activate NEW DATA ENTRY function. ▲ Enter a new data by operating the buttons as explained in “HOW TO ENTER CHARACTERS” on pages 17 - 18.
CORRECTING THE DATA E Turn clockwise or counterclockwise to select the data to be corrected. ▲ B Press for 2 to 3 seconds to show MENU display. ▲ E While “EDIT” is flashing, press to activate DATA CORRECTION function. English ▲ E Turn clockwise or counterclockwise to select the data correction operation (EDIT). ▲ Correct the data by operating the buttons as explained in “HOW TO ENTER CHARACTERS” on pages 17 - 18. ▲ E After the data is corrected, press to deactivate DATA CORRECTION function.
DELETING ONE DATA E Turn clockwise or counterclockwise to select the data to be deleted. ▲ B Press for 2 to 3 seconds to show MENU display. ▲ ▲ E ▲ English E E Turn clockwise or counterclockwise to select the single data deletion operation (DEL). While “DEL” is flashing, press to activate SINGLE DATA DELETION function. Press while “YES” is flashing. ▲ E Press and hold for 4 seconds to delete the selected data. * A confirmation sound beeps and “DELETE COMPLETE” is displayed for 2 seconds.
DELETING THE ENTIRE DATA B Press for 2 to 3 seconds to show MENU display. ▲ E ▲ E While “CLR” is flashing, press to activate ALL DATA CLEAR function. Press while “YES” is flashing. ▲ ▲ E English E Turn clockwise or counterclockwise to select the all data clear operation (CLR). Press and hold for 4 seconds to delete all the data. * A confirmation sound beeps and “ALL CLR COMPLETE” is displayed for 2 seconds. Then, the display returns to URL MEMO mode.
DISPLAYING THE URL MEMO ● Selection of the URL memo English E Turn clockwise or counterclockwise. * With each turn, the first 16 characters of a stored URL memo are displayed. * The stored data is displayed one by one starting from the last to the first or the first to the last according to the data arrangement in memory by turning button E counterclockwise or clockwise, respectively. ● Scroll display of the selected URL memo E Press after selecting a desired URL memo.
HOW TO ENTER CHARACTERS A C E English ● Selection of type of characters Press to select the type of characters. ➾ Katakana ➾ (Japanese characters) English capital letters Numerals and symbols English small letters ➾ ➾ A ● Selection of characters in Japanese syllabary, alphabetical or numerical order E Turn counterclockwise.
● Selection of characters in reverse Japanese syllabary, alphabetical or numerical order E Turn clockwise. ● Character entry / rightward advancement of cursor E Press to enter the character indicated by the cursor. English ● Space insertion A & C Press at the same time. ● Deletion of one character C & E Press button E while keeping button C pressed. ● Rightward advancement of the cursor C & E Turn button E counterclockwise while keeping button C pressed.
MEMORY CAPACITY INDICATION C C Press to show the residual memory capacity for URL MEMO mode. Residual memory capacity / Total memory capacity English * The residual memory capacity is displayed for 2 seconds, and the watch automatically returns to the display previously shown. * The watch will also return to the display previously shown by pressing button B, C or E.
English MESSAGE MODE ● Up to 10 messages, each of which contains up to 60 characters, can be registered and displayed together with the date when they are to be displayed. ● On the designated date, the registered message scrolls on the display every 10 minutes. ● The scrolling message also appears by pressing button E in the TIME/CALENDAR mode. (See “DISPLAYING MESSAGES” on page 5) ● The residual memory capacity can also be indicated.
NOTES ON USING THE WATCH MODE CHANGE English ● When the confirmation sound is turned on, a beep sounds with each press of button A to change over the mode. It sounds in a different tone when the TIME/CALENDAR mode appears, so that you can easily know the mode shown. ● Note on button E operation: To operate the watch with button E, push it, turn it clockwise or counterclockwise. • Turning clockwise: Set the knob to the leftmost position. • Turning counterclockwise: Set the knob to the rightmost position.
English minute is added and the seconds are reset to “00”. ● The flashing digits except the seconds and 12-/24-hour indication move quickly if button E is kept at the rightmost or leftmost position. ● If the watch is left untouched with the digits flashing, it will automatically return to the TIME/CALENDAR mode in 2 to 3 minutes. ● Note on unusual display: While setting the time/calendar, all the segments of the display will light up if both buttons C and D are pressed at the same time.
TIMER MODE English [PRESET TIMER SETTING] ● The selection of the preset time is made quickly if button E is kept at the rightmost or leftmost position. [ADJUSTABLE TIMER SETTING] ● The flashing digits move quickly if button E is kept at the rightmost or leftmost position. ● If the watch is left untouched with the digits flashing, it will automatically return to the TIMER mode in 2 to 3 minutes.
English 24 [ALARM ENGAGEMENT/DISENGAGEMENT] ● When any one of the alarms is engaged, the alarm mark is displayed in the TIME/ CALENDAR mode. ● At the designated time, the regular alarm rings for 20 seconds as the message “Wake up!” scrolls. To stop them manually, press any one of the buttons. ● At the designated time, the single-time alarm rings for 20 seconds as the message “Let’s go!” scrolls. To stop them manually, press any one of the buttons.
English you have entered will not be registered in memory. ● Notes on correcting the data: • If the corrected data contains no character, that is, if all the characters of the data are deleted and button B is pressed, “DELETE? (YES/NO)” is displayed. After you choose “YES” or “NO” by turning button E, the watch returns to the URL MEMO mode.
English 26 CLR? (YES/NO)” is displayed, and press button E. The watch will return to the MENU display. • If button B is pressed while “ALL CLR? (YES/NO)” is displayed, the data will not be cleared and the watch will return to the URL MEMO mode. [DISPLAYING THE URL MEMO] ● When button E is turned clockwise or counterclockwise while a URL memo is scrolling, it will stop on the spot. Turning button E again clockwise or counterclockwise will put back or advance the URL memo by one character, respectively.
while keeping button C pressed. ● Types of characters: The following characters can be used to enter the data. • Katakana : ア イ ウ エ オ カ キ ク ケ コ サ シ ス セ ソ タ チ ツ テ トナ ニ ヌ ネ ノ ハヒフヘホマミムメモヤユヨラリルレロワヲン ア イ ウ エ オ ヤ ユ ヨ ツ ー 。 • English capital letters : A B C D E F G H I J K L M N O P Q R S T U V W X Y Z • English small letters : abcdefghijklmnopqrstuvwxyz • Numerals and symbols : 0 1 2 3 4 5 6 7 8 9 – ( ) .
English ● To protect the registered URL memos/messages from damage or loss in case of accident, malfunction, repair, loss or theft of the watch, be sure to keep data sources such as business cards or note down important URL memos/messages in a notebook or the like. Please note that we are not liable for any damage or lost profits resulting from the use of this watch and the loss or change of the registered data caused by malfunction or repair of the watch.
BATTERY CHANGE 2 Battery life : Approx. 2 years Years Battery : SEIKO CR2025 English ● The battery life may be less than 2 years if the alarm is used for more than 20 seconds a day, the timer more than once a day, the confirmation sound more than 50 times a day, and/or the illuminating light more than 3 times a day. ● As the battery is inserted at the factory to check the function and performance of the watch, its actual life once in your possession may be less than the specified period.
2) 3) “SYSTEM ERROR 0” is displayed. The display becomes blank. ● Necessary procedure after battery change English After the battery is replaced with a new one, follow the procedure below to reset the IC. Press and hold buttons A, B, C and D at the same time for 2 to 3 seconds. The display shown at right appears. * Before using the watch, perform the following in the order below by referring to the corresponding sections of this manual.
CAUTION ● The battery is not rechargeable. Never attempt to recharge it, as this may cause battery leakage or damage to the battery.
TROUBLESHOOTING English Trouble Cause Solution The display becomes blank. •The battery has run down. Have the battery replaced with a new one immediately by the retailer from whom the watch was purchased. “BATTERY LOW!” is displayed or all the digits are flashing. •The battery nears its end. Have the battery replaced with a new one by the retailer from whom the watch was purchased. “SYSTEM ERROR 0” is displayed, the watch does not indicate the time correctly, or an abnormal display appears.
TO PRESERVE THE QUALITY OF YOUR WATCH WATER RESISTANCE ● Non-water resistant • If the watch becomes wet, have it checked by an AUTHORIZED PULSAR DEALER or SERVICE CENTER. 5 bar WR 10/15/20 bar WR • Do not operate the buttons when the watch is wet or in water. If used in sea water, rinse the watch in fresh water and dry it completely.
* Pressure in bar is a test pressure and should not be considered as corresponding to actual diving depth since swimming movement tends to increase the pressure at a given depth. Care should also be taken on diving into water. ** We recommend that you wear a PULSAR Diver’s Watch for scuba diving. English TEMPERATURES 34 Your watch works +50°C with stable accuracy within a temperature -5°C range of 5° C and 35° C (41° F and 95° F).
SHOCKS & VIBRATION PERIODIC CHECK Be careful not to expose the watch to solvents, mercury, cosmetic spray, detergents, adhesives or paints. Otherwise, the case, bracelet, etc. may become discolored, deteriorated or damaged. PRECAUTION REGARDING CASE BACK PROTECTIVE FILM English Light activities will not It is recommended that the affect your watch, but be watch be checked once 2-3 careful not to drop your every 2 to 3 years.
English STATIC ELECTRICITY 36 The IC (Integrated Circuit) used in your watch will be affected by static electricity which may disturb the display. Keep the watch away from close contact with objects such as TV screens which emit strong static electricity. LIQUID CRYSTAL PANEL The normal life expectancy for the liquid crystal panel of the watch is approximately 5 years. 5 Years After that it may decrease in contrast, becoming difficult to read.
