CAL.
MODE CHANGE A A With each press, the mode changes in the following order: ➡ TIME/ CALENDAR 2 ➡ SINGLE-TIME ALARM ➡ REGULAR ALARM
TIME/CALENDAR MODE TIME/CALENDAR SETTING Hour A ▲ C A Press to show TIME/ CALENDAR mode. Press for 2 to 3 seconds. ▲ ▲ C ▲ A D D Select the digits to be adjusted.✽ Set the flashing digits. ▲ Minutes A Return to TIME/CALENDAR mode.
✽ Selection of the digits Minutes Hour Date Month ▲ ▲ ▲ ▲ * If the flashing “– –” is shown in the middle row of the display, the digits indicate the time, and otherwise, they indicate the calendar. C Month Date 4 SHOWING THE CALENDAR DISPLAY C Press and hold in TIME/ CALENDAR mode. * While the button is kept pressed, the month and date are displayed.
SINGLE-TIME ALARM MODE ● The single-time alarm can be set to ring only once at the designated time. As it rings, it is automatically disengaged. ● The single-time alarm can be set in minute increments starting from the current time. SINGLE-TIME ALARM SETTING Hour A ▲ C Press to show SINGLE-TIME ALARM mode. C or D Set the desired alarm time. ▲ A Minutes A D Return to TIME/CALENDAR mode. * The single-time alarm mark “1AL” remains displayed and the single-time alarm is engaged.
* At the designated time, the single-time alarm rings for 20 seconds. To stop it manually, press any of the buttons. ● To cancel the single-time alarm you have set, press buttons C and D at the same time in the SINGLE-TIME ALARM mode, or press button C or D to set the alarm time to the current time.
REGULAR ALARM MODE ● The regular alarm can be set to ring on a 24-hour basis. A Press to show REGULAR ALARM mode. REGULAR ALARM SETTING Regular alarm mark Hour A C Press for 2 to 3 seconds. ▲ C or D Set the desired alarm time. ▲ A A D Minutes Return to REGULAR ALARM mode. * The regular alarm mark is automatically displayed and the regular alarm is engaged.
ENGAGEMENT/DISENGAGEMENT OF REGULAR ALARM AND HOURLY TIME SIGNAL Regular alarm mark C C With each press in REGULAR ALARM mode, the engagement/disengagement of the regular alarm and hourly time signal are made as follows: ▲ Both engaged ▲ Regular alarm engaged ▲ Neither engaged ▲ Hourly time signal engaged Hourly time signal mark * At the designated time, the regular alarm rings for 20 seconds. To stop it manually, press any of the buttons.
ILLUMINATING LIGHT (Electroluminescent panel) B B Turn on the illuminating light. * The display panel is evenly illuminated for 3 seconds. ViViDiGi ● is a new type of liquid crystal panel that makes possible various colors and high contrast. ● Excellent light reflection and transmission make the display bright and clear. ● Various color options are available. ● Either the whole panel or the displayed data only can be illuminated. * Features vary in different models.
NOTES ON USING THE WATCH MODE CHANGE ● The displayed numerals have unique forms. The positions where they are shown on the display, therefore, shift between both sides of the display, depending on the numeral shown. ● If the watch is left untouched in the SINGLE-TIME ALARM and REGULAR ALARM mode, it will automatically return to the TIME/CALENDAR mode in 2 to 3 minutes. TIME/CALENDAR MODE 10 [TIME/CALENDAR SETTING] ● The calendar automatically adjusts for odd and even months except February of leap years.
is displayed. For the AM setting, there is no indication. ● As button “A” is pressed to return to the TIME display, the second digits are automatically reset to “00” and start counting immediately. (See “● Setting the seconds” explained above) ● If the watch is left untouched with the digits flashing, it will automatically return to the TIME/CALENDAR mode in 1 to 2 minutes.
● If the watch is left untouched in the SINGLE-TIME ALARM mode, it will automatically return to the TIME/CALENDAR mode in 2 to 3 minutes. ● The single-time alarm rings differently from the regular alarm. REGULAR ALARM MODE ● If the watch is left untouched in the REGULAR ALARM mode, it will automatically return to the TIME/CALENDAR mode in 2 to 3 minutes. [REGULAR ALARM SETTING] ● With each press of button C or D, one minute is advanced or moved back, respectively.
ILLUMINATING LIGHT (Electroluminescent panel) ● The electroluminescent panel loses its luminance as the battery voltage gets lowered. Also, its luminance level decreases gradually with use. After 120 hours of use, the level decreases by about half. ● When the illuminating light becomes dim, replace the battery with a new one. If the light remains dim after the battery is replaced, have the electroluminescent panel replaced with a new one by the retailer from whom the watch was purchased.
● When the battery expires, be sure to replace it as soon as possible to prevent any malfunction. ● We recommend that you contact an AUTHORIZED PULSAR DEALER for battery replacement. WARNING ● Do not remove the battery from the watch. ● If it is necessary to take out the battery, keep it out of the reach of children. If a child swallows it, consult a doctor immediately. ● Never short-circuit, tamper with or heat the battery, and never expose it to fire. The battery may burst, become very hot or catch fire.
TO PRESERVE THE QUALITY OF YOUR WATCH WATER RESISTANCE ● Non-water resistant • If the watch becomes wet, have it checked by an AUTHORIZED PULSAR DEALER or SERVICE CENTER. ● Water resistant 5/10/15/20 bar 5 bar WR 10/15/20 bar WR • Do not operate the buttons when the watch is wet or in water. If used in sea water, rinse the watch in fresh water and dry it completely.
* Pressure in bar is a test pressure and should not be considered as corresponding to actual diving depth since swimming movement tends to increase the pressure at a given depth. Care should also be taken on diving into water. ** We recommend that you wear a PULSAR Diver’s Watch for scuba diving. TEMPERATURES Your watch works with +50°C stable accuracy within a temperature range of 5° C -5°C and 35° C (41° F and 95° F).
SHOCKS & VIBRATION PERIODIC CHECK Light activities will not It is recommended that the affect your watch, but be watch be checked once 2-3 careful not to drop your every 2 to 3 years. Have Years watch or hit it against hard your watch checked by an surfaces, as this may AUTHORIZED PULSAR cause damage. DEALER or SERVICE CENTER to ensure that the case, buttons, gasket and crystal seal remain intact.
STATIC ELECTRICITY The IC (Integrated Circuit) used in your watch will be affected by static electricity which may disturb the display. Keep the watch away from close contact with objects such as TV screens which emit strong static electricity. 18 LIQUID CRYSTAL PANEL The normal life expectancy for the liquid crystal panel of the watch is approximately 5 years. 5 Years After that it may decrease in contrast, becoming difficult to read.
