CAL.
MODE CHANGE ILLUMINATING LIGHT C C ADJUST D D RECALL/+/START/LAP English A A E TOGGLE/-/SAVE/ STOP With each press, the mode changes in the following order. TIME MODE A ALARM MODE ALTIMETER MODE TIMER MODE WEATHER MODE DATA MODE STOPWATCH (CHRONO) MODE E English MODE B Press to turn the backlight on. If you keep holding down the button for 2 seconds until the watch generates a beep sound, the backlight remains lighted for 15 seconds after the button is released.
s TIME MODE D Press to increase the digits (+) or move forward. or Day of the week E Date A Altitude Press to select the items to be adjusted. Sequence of the item settings HOUR MINUTE SECOND DAY TIME/CALENDAR SETTING C English English Time MONTH Keep holding down for 2 seconds. “ADJUST HOLD” is shown, and the watch enters the TIME SETTING mode. C C D D CONTRAST LEVEL B B The hour digits start flashing.
Time format Select either 12-hour indication format or 24-hour indication format. Calendar format Select either "Day of the week-Date” format or “Month-Date” format. Power save English Two time zones (T1 and T2) are provided. Time zone indicator s C Press to confirm the settings and return to the TIME mode. C D A E B D D and E Keep holding down at the same time to hear the alarm sound.
ALTIMETER MODE A Press until the watch enters the ALTIMETER mode. Upon entering the ALTIMETER mode, the accumulated altitude and maximum altitude scroll across the top of the display. Then, a graphic data display of elevation changes over the past two hours is shown. Readout units (feet/meters) English Rate of ascend/descend Accumulated altitude E Keep holding down for 2 seconds to change the readout units.
English C Press to increase the value (+) in 5 ft increments. E Press to decrease the value (-) in 5 ft increments. C Press to complete the altitude calibration. English how to calibrate the Altimeter D or s Altimeter calibration This watch estimates altitude based on the barometric pressure measured by high sensitivity barometer.
s How to reset the accumulated altitude and maximum altitude “ADJUST HOLD” is shown, and the watch enters the ALTIMETER SETTING mode. The altitude digits start flashing. s C D C D A E C D A E B B B A E Press to go to the maximum altitude display. The maximum altitude digits start flashing. A E C D D or E Press to reset the accumulated altitude to zero. B B Press to reset the maximum altitude to zero.
Press to select the sample rate among "60 seconds," "10 seconds," and "2 seconds." C D B B A s English D E C D A E A E Press to go back to the ALTIMETER mode display. Sample rate 1 hour ago 5 minutes ago now B In the Altimeter Mode, the default measurement interval is set to 60 seconds. This rate can be changed to either 2-second intervals with time limit of maximum 10 minutes or 10-second intervals with time limit of maximum 60 minutes.
When the altitude exceeds the range of the graphic data display 16 Example: 5 minutes after the graphic data on the previous page is displayed, the altitude was 10 meters lower. Mountain name display When elevation reach a height equal to that of a particular mountain, the watch generates a beep sound and the name of the mountain and its height scroll across at the top of the display for 30 seconds. Mountain names Height (m) Height (ft) Mt. Mckinley 6,194 20,321 Mt.
barometric pressure, temperature and barometric pressure trend weather MODE A D Press until the watch enters the WEATHER mode. barometric pressure trend Keep holding down for 2 seconds to change the display format between the "Current temperature" and the "Barometric pressure with current temperature" format. D D English English barometric pressure temperature E When the "Current temperature" format is selected, the barometric pressure is not displayed.
s Set the offset value (between -20 and +20) to compensate for the difference between the currennt temperature reading and the reference temperature. D Press to increase the value (+). E Press to decrease the value (-). Temperature calibration HOW TO CALIBRATE THE Temperature s C C In the WEATHER mode, keep holding down for 2 seconds. “ADJUST HOLD” is shown, and the watch enters the TEMPERATURE SETTING mode. The offset value as "zero" starts flashing.
Graphic data display of barometric pressure trend At the top of the display, the watch provides a graphic data display of barometric pressure trend over the past twelve hours. 22 7 divisions 30 minutes ago now 24 divisions • One division of the vertical axis is 2hPa, one division of horizontal axis is 30 minutes. • The blinking column at far right indicates current barometric pressure.
When the barometric pressure exceeds the range of the graphic data display A Press until the watch enters the STOPWATCH mode. Run number Example: 30 minutes after the graphic data on the previous page is displayed, the barometric pressure was 2hPa lower. 24 STOPWATCH (CHRONO) MODE l The stopwatch measures up to 99 hours, 59 minutes and 59.99 seconds in 1/100 second increments.
How to check the remaining memory capacity When the stopwatch is not in motion, press to check the remaining memory capacity . C D E To save the record E Remaining memory capacity stopwatch operation Press to start the stopwatch. D lap 1 s D Press to take a lap time. C D lap 2 Up to 50 lap times can be recorded. D Lap time Lap number (flashing) A Keep holding down for 2 seconds. The RUN record is stored in memory and the stopwatch is set for the next measurement with a new RUN number.
Press to switch the display between lap time display and total time display while a measurement is in progress. C D C B A E D A Press until the watch enters the DATA mode. E Press to select the RUN number. B C D A E B A E D English English C s C DATA MODE how to view the data contents s Switching between lap time display and total time display during a measurement Press to view the contents of the selected RUN data.
how to delete the RUN data C Timer mode Keep holding down for 2 seconds to delete the selected RUN data. D A E C D English B C Keep holding down again for 4 seconds to delete all the stored data. B l The 5-segment timer counts up to 99 hours, 59 minutes and 59 seconds in 1 second increments. A Press until the watch enters the TIMER mode.
timer setting C D D Press to select the desired starting segment (from 1 to 5). D Press to start the timer. When the timer counts down to zero, it beeps and immediately starts counting down for the next segment. The timer repeats counting in ascending order of the segment number up to 200 times. To repeat counting the same one segment, set all other segments to “0.” B B A E A E s s D Press to increase the digits (+). E Press to decrease the digits (-). E Press to stop the timer.
C ALARM MODE A Press until the watch enters the ALARM mode. “ADJUST HOLD” is shown, and the watch enters the ALARM SETTING mode. The alarm has 7 channels: the Alarm 1 to 4 are the TIME alarm, the Alarm 5 and 6 are the ALTIMETER alarm, and the Alarm 6 is H2O alarm. s A C D A E B B A E Press to select the digits to be adjusted (hour/minute). s Alarm channel Alarm mark D Press to increase the digits (+). E Press to decrease the digits (-). C Press to confirm the alarm setting.
ALTIMETER alarm setting H2O alarm setting l The H2O alarm is a hydration reminder, which generates an alert sound to remind you to drink water when a preset time (up to 60 minutes) has elapsed. E Press to select the desired alarm channel (5 or 6). C Keep holding down for 2 seconds to show the ALARM SETTING display. s D Press to increase the digits (+). D A A E E C s 36 Press to confirm the alarm setting. “ON” and the alarm mark appear and the alarm is automatically engaged.
ALARM ENGAGEMENT/DISENGAGEMENT E s D With each press, the selected alarm is engaged and disengaged alternately. D D C C D Alarm mark A E A E Keep holding down for 4 seconds to disengage all the alarm at one time. D C D C E s B A 38 B E B A E At the designated time, the TIME alarm sounds for 35 seconds with two 10-second intervals. The ALTIMETER alarm and H2O alarm sound for 5 seconds. To stop the alarm while it is sounding, press any button. 2 Years Battery life : Approx.
Press and hold buttons A, B, C and D at the same time for 2 to 3 seconds. The display will become blank. When the buttons are released, time/calendar display will appear and “2007 1-JAN 12:00'00" MON” will be displayed. * Before using the watch, set the time/calendar and alarm. CAUTION l The battery is not rechargeable. Never attempt to recharge it, as this may cause battery leakage or damage to the battery.
NOTE: Pressure in bar is a test pressure and should not be considered as corresponding to actual diving depth since swimming movement tends to increase the pressure at a given depth. Care should also be taken on diving into water. TEMPERATURES Operational temperature range: Between -5° C (+23° F) and 50° C (122° F) +50°C 0°C +50°C 5°C MAGNETISM Your watch will not be affected by magnetism.
It is recommended that the watch be 2-3 checked once every 2 Years to 3 years. Have your watch checked by an AUTHORIZED PULSAR DEALER or SERVICE CENTER to ensure that the case, buttons, gasket and crystal seal remain intact. PRECAUTION REGARDING CASE BACK PROTECTIVE FILM STATIC ELECTRICITY The IC (Integrated Circuit) used in your watch will be a ff e c t e d b y s t a t i c electricity which may disturb the display.
