CAL. Y182, 7T32 ALARM CHRONOGRAPH ALARM Can be set on a 12-hour basis with small alarm hands. STOPWATCH Measures up to 30 minutes in 1/5 second increments.
DISPLAY AND CROWNS/BUTTONS There are three buttons and two crowns.
SCREW DOWN CROWN [for models with screw down crown] Unlocking the crown 1 Turn Crown counterclockwise until you no longer feel the threads turning. 2 Crown can be pulled out. 1 Push Crown back in to normal position. 2 Turn Crown clockwise while pressing it lightly until tight.
DATE SETTING CROWN 1 Date 1 Pull out to first click. 1 ▲ ➠ 2 English 5 2 Turn clockwise until the date for the previous day appears. ▲ CROWN 1 3 Pull out to second click and turn until the desired date appears. ▲ 3 ➠ 6 ➠ 4 4 4 Push back in to normal position.
TIME SETTING CROWN 1 Minute hand 1 Pull out to second click when Second hand is at the 12 o’clock position. 1 ▲ 2 ➠ 3 CROWN 1 2 Turn to set Hour and Minute hands. English ➠ ▲ Hour hand 3 Push back in to normal position in accordance with a time signal.
ALARM Alarm time is set on a 12-hour basis and indicated by ALARM hour and minute hands that move independently of MAIN TIME hands. ALARM SETTING After the main time is adjusted, follow the procedure below, and then set the alarm. * The following procedure is necessary only after the main time is adjusted. Minute hand (MAIN TIME) CROWN 2 ➠ 3 ALARM hands 1 Pull out to second click. 2 Turn to set ALARM hands to the current time (MAIN TIME).
2 Alarm time setting * Once ALARM hands are adjusted to the main time, alarm time setting can be made only by following the procedure below. CROWN 2 CROWN 2 Pull out to first click. ▲ C ▲ CROWN 2 ➠ C Push back in to normal position. English ➠ Press repeatedly to set ALARM hands to the desired alarm time.
ALARM ENGAGEMENT/DISENGAGEMENT 1 Alarm engagement 2 Alarm disengagement Pull out to first click. CROWN 2 Push back in to normal position. English CROWN 2 8 ➠ Current time ➠ Designated alarm time ● Alarm rings at the designated time for 20 seconds. * To stop it manually, press Button A, B or C, or push CROWN 2 back in to normal position.
STOPWATCH Stopwatch measures up to 30 minutes in 1/5 second increments. After 30 minutes, it will start counting again from “0” repeatedly up to 6 hours. STOPWATCH OPERATION * If the hands do not return to “0” position, follow the procedure in “ADJUSTING THE HAND POSITION” (page 12). English ● Before using the stopwatch: 1 Check that CROWNS 1 and 2 are set at normal position. 2 Press Button B to reset STOPWATCH hands to “0” position.
TACHYMETER [for models with tachymeter scale on the dial] To measure the hourly average speed of a vehicle English Tachymeter scale: “90” “90” (tachymeter scale figure) x 1 (km or mile) = 90 km/h or mph 10 1 Use the stopwatch to determine how many seconds it takes to go 1 km or 1 mile. ▲ Ex. 1 STOPWATCH second hand: 40 seconds 2 Tachymeter scale indicated by STOPWATCH second hand gives the average speed per hour. Tachymeter scale can be used only when the time required is less than 60 seconds. Ex.
“90” (tachymeter scale figure) x 2 (km or mile) = 180 km/h or mph “90” (tachymeter scale figure) x 0.5 (km or mile) = 45 km/h or mph To measure the hourly rate of operation Tachymeter scale: “180” “180” (tachymeter scale figure) x 1 job = 180 jobs/hour 1 Use the stopwatch to measure the time required to complete 1 job. 2 Tachymeter scale indicated by STOPWATCH second hand gives the average number of jobs accomplished per hour. English STOPWATCH second hand: 20 seconds ▲ Ex. 1 Ex.
ADJUSTING THE HAND POSITION If STOPWATCH hands will not return to the 12 o’clock position when the stopwatch is reset or when the battery is replaced with a new one, follow the procedure below. CROWN 1 ▲ English A ➠ A ▲ ➠ CROWN 1 B CROWN 1 12 Press repeatedly to reset STOPWATCH minute hand to the 12 o’clock position. Press repeatedly to reset STOPWATCH second hand to the 12 o’clock position. ▲ B Pull out to second click. Push back in to normal position.
RESETTING THE BUILT-IN IC In case any of the hands should move improperly, follow the procedure below to adjust the hand movement. CROWN 1 A Pull out to second click. ▲ A AND B Press simultaneously. CROWN 1 English ➠ ▲ ➠ B Push back in to normal position.
NOTES ON OPERATING THE WATCH DATE SETTING English ● Do not set the date between 9:00 p.m. and 3:00 a.m. Otherwise, the date may not change properly. * If it is necessary to set the date during that time period, first change the time to any time outside this period, set the date and then reset the correct time. ● It is necessary to adjust the date at the end of February and 30-day months. TIME SETTING ● When setting Hour hand, check that AM/PM is correctly set.
● If CROWN 2 is pulled out to first click within 1 minute after being pushed back in to normal position, the alarm sounds. ● If CROWN 2 is pulled out to second click, the designated alarm time is canceled with a warning beep. * In that case, set ALARM hands to MAIN TIME again, push CROWN 2 back in to normal position, and then, pull it out to first click and set the desired alarm time again.
BATTERY CHANGE 2 English Years Battery life : Approx. 2 years Battery : SEIKO SR927W ● As the battery is inserted at the factory to check the function and performance of the watch, its actual life once in your possession may be less than the specified period. ● When the battery expires, be sure to replace it as soon as possible to prevent any malfunction. ● We recommend that you contact an AUTHORIZED PULSAR DEALER for battery replacement.
WARNING ● Do not remove the battery from the watch. ● If it is necessary to take out the battery, keep it out of the reach of children. If a child swallows it, consult a doctor immediately. ● Never short-circuit, tamper with or heat the battery, and never expose it to fire. The battery may burst, become very hot or catch fire. English CAUTION ● The battery is not rechargeable. Never attempt to recharge it, as this may cause battery leakage or damage to the battery.
TO PRESERVE THE QUALITY OF YOUR WATCH WATER RESISTANCE ● Non-water resistant English • If the watch becomes wet, have it checked by an AUTHORIZED PULSAR DEALER or SERVICE CENTER. ● Water resistant 5/10/15/20 bar 5 bar WR 10/15/20 bar WR 18 • Before using in water, be sure the crowns are pushed in completely. • Do not operate the crowns and buttons when the watch is wet or in water. If used in sea water, rinse the watch in fresh water and dry it completely.
* Pressure in bar is a test pressure and should not be considered as corresponding to actual diving depth since swimming movement tends to increase the pressure at a given depth. Care should also be taken on diving into water. ** We recommend that you wear a PULSAR Diver’s Watch for scuba diving. TEMPERATURES MAGNETISM N S Your watch will be adversely affected by strong magnetism. Keep it away from close contact with magnetic objects.
English SHOCKS & VIBRATION 20 PERIODIC CHECK Light activities will not It is recommended that the affect your watch, but be watch be checked once 2-3 careful not to drop your every 2 to 3 years. Have Years watch or hit it against hard your watch checked by an surfaces, as this may AUTHORIZED PULSAR cause damage. DEALER or SERVICE CENTER to ensure that the case, crowns, buttons, gasket and crystal seal remain intact.