NOTE: TO OPERATE, PUSH START SCOOTER TO APPROXIMATELY 3 MPH WHILE STANDING ON THE DECK IN ORDER FOR MOTOR TO ENGAGE. THE SCOOTER MUST BE ROLLING AT 3 MPH BEFORE THE MOTOR WILL ENGAGE. ELECTRIC SCOOTER OWNER’S MANUAL FOR USE WITH THE FOLLOWING PULSE PERFORMANCE PRODUCTS™ SCOOTERS • DURA STREET DO NOT RETURN TO STORE! QUESTIONS OR COMMENTS? CALL (866)-434-6067 NOTE: Manual illustrations are for reference purposes only. Illustrations may not reflect the exact appearance of the actual product.
Table of Contents Safety and Warnings Before You Start Assembly Hardware Maintenance Before You Ride Repair and Maintenance Troubleshooting Scooter Components Warranty 2-3 4 5-6 7 7 8-9 10 11 12 Safety and Warnings WARNING: Riding an electric scooter can be a dangerous activity. Certain conditions may cause components to fail without fault of the manufacturer.
Safety and Warnings rnings Maintain a hold with both hands on the handlebars at all times. Never allow more than one person at a time to ride the scooter. Never use near steps, water, or swimming pools. , steering system, wheels and all other moving components. Never ride while using a cell phone or wearing headphones. Never hitch on to or with another vehicle or pull anyone or anything.
Before You Start WARNING: Remove all packing and items from the display box. Make sure that the power switch is turned “OFF” before assembling the scooter. Estimated Assembly Time • Allow up to 25 minutes for assembly, not including initial charge time. • Allow up to 12 hours for the initial charge (see page 6 for charging information).
Assembly Front Wheel Assembly Tools required: 13mm wrench, 17mm wrench 1. Remove and discard protective fork cap. 2. Insert front axle and hardware through front wheel and fork 3. Ensure that the hardware is correctly assembled, tighten axle hardware securely with a 13mm and 17mm wrench. Handlebar Steer Tube Assembly: 1. Depress the push button located on the rear of the fork and insert the handlebar steer tube onto the fork.
Assembly Charging the Battery WARNING: Battery must be fully charged before you ride your electric scooter. Required components: battery charger • Initial battery charge time - 12 hours • Recharges after initial charge - up to 10 hours • When scooter is not in regular use batteries need to be charged on a monthly basis to maximize performance 1. Make sure power switch is in the OFF position before plugging in the charger. Insert charger into charging port located in the rear of the battery box. 2.
Hardware Maintenance Brake Check the brakes for proper function. When you step on the brake it should provide positive braking action. When you apply the brake with the hub motor activated the brake cut off switch should cut power off to the motor. Frame, Fork and Handlebars Check for cracks or broken connections. Although broken frames are rare, it is possible for aggressive rider to run into a curb or wall and bend or break a frame. Get in the habit of inspecting your scooter on a regular basis.
Repair and Maintenance Front Wheel Replacement Tools required: 13mm wrench, 17mm wrench 1. Using 13mm and 17mm wrenches loosen and remove the front axle by turning the wrenches counter clockwise. 2. Reinstall new replacement wheel ensuring to note the order and location of all components. 3. Using 13mm and 17mm wrenches securely tighten axle hardware clockwise. Battery Care and Disposal Do not store the battery in temperatures above 70°F (21°C) or below 32°F (0°C).
Repair and Maintenance Battery Charger Only use the supplied battery charger. If battery charger is damaged discontinue use immediately and replace with a Pulse Performance Products™ recommended battery charger. Wheels Wheels and drive system components are subject to normal wear and tear. It is the responsibility of the user to regularly inspect wheels for excess wear and adjust and replace drive train components as required.
Troubleshooting Problem Possible Cause Solution Scooter will not run. Battery is not charged. Fully charge the battery. First charge should be 12 hours and up to 10 hours for recharges. Wires or connectors are loose or unplugged. Check to ensure that charger is tightly plugged into both the wall and the scooter. Must be rolling 3mph (5 km/h) for motor to engage. Push start scooter to approximately 3 MPH (5 km/h) while standing on the deck in order for motor to engage.
Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call (866) 434-6067.
Warranty Limited Warranty The manufacturer warranties this product to be free of manufacturing defects for a period of 90 days from the date of purchase. This Limited Warranty does not cover normal wear and tear, tires, cables, or any damage, failure or loss caused by improper assembly, maintenance, storage or use of this Pulse Performance Products™ electric scooter. This warranty is limited to the replacement of defective parts only.
facebook.com/pulseperfprod twitter.com/pulseperfprod Pulse Performance Products™ A Division of Bravo Sports™ 12801 Carmenita Rd.
