Owner's Manual

5
Assembly
After installing your ShowerSpa, some assembly is required prior to use.
Attaching The Accessories
1. Locate the desired mounting location of the handheld holder (6) and mark the holes (we recommend placing it near the height
of the glass shelf). Drill ¼" holes through wall surface using a masonry bit. Drill slowly through wall surface to avoid cracking and
chipping. Insert anchors and securely screw mount to wall.
NOTE—To adjust angle of handheld shower, loosen knob, gently rotate toward you or toward the wall, then tighten knob.
2. Insert rubber washer (11) into hexagon shaped end of handheld hose (7) and attach to threaded outlet on bottom of ShowerSpa.
DO NOT OVER-TIGHTEN.
3. Insert rubber washer (11) into tapered end of handheld hose (7) and attach to handheld shower (5). Place into handheld holder.
4. Place the female threaded end of the shower arm (3) over the male threads on top of the shower arm bracket (4). Hand tighten
until secure. The shower arm should swing freely from side to side for ideal positioning.
5. Check that rubber washer (11) is in shower head (2) and screw shower head onto the shower arm (3).
Installation – New Construction
Extensive Remodel – New Finished Wall Surface
 1. Priortosheetrock,stub-out½"hotandcoldsupplylinesbeyondnishedwallsurface,4"oncenter.Forbestresults,attach90°
brassttings(availableatmosthardwarestores)tothestub-outsmaintaining¼"–½"ofspacebetweenthettingandnished
wall.Theopenendofthe90°brassttingsshouldpointdownsothesupplylinesattachparalleltothewall.
1
2. The height of the stub-outs is completely dependent upon the desired mounting height of your ShowerSpa. For a person
5'8"–6'2"werecommendthestub-outsbe39"fromnishedoor.
2
 3. BeforeyouinstalltheShowerSpa,makecertainwateriscompletelyturnedotobothhot&coldsupplylinesoftheshower.
4. Mark the location of holes for the mounting brackets, making sure brackets are level. For a person 5'8" – 6'2" tall, we recommend
putting the top bracket 65
5
/ 8"fromnishedoorheight.
3
The bottom bracket should be positioned exactly 23 ¼" below the top
bracketwiththeholesplumbtotheupperbracketholes.Beforedrillingholesforbracket,makecertainShowerSpawillrestat
againstnishedwallsurfaceatdesiredmountingheightwithsupplylinesconnected.
5. Drill ¼" holes through wall surface using a masonry bit. Drill slowly through wall surface to avoid cracking and chipping. Insert
anchors and securely screw brackets to wall. Before connecting hot and cold supply lines, hang the ShowerSpa on wall, check
theheightandmakesuretheShowerSpaisushagainstwallwithasecuret.
6. Connect hot and cold water supply lines to stub-outs—DO NOT OVERTIGHTEN.BeforemountingtheShowerSpa,checkttings
tomakesuretheyaresecure.Turnonwaterandcheckforleaks.Whenttingsareleak-free,mountShowerSpaonwall.
7. OPTIONAL—Seal around body of ShowerSpa with a bead of silicone. DO NOT SEAL BOTTOM.
1
Additionalttingsmaybenecessarydependingonyourspecicsituation.
2
The desired mounting height of ShowerSpa determines height of the ½" stub-outs. The stub-outs must be located at a height
allowingsupplylinestobeconnectedandbodyofShowerSpatorestatagainstnishedwall.
3
The mounting height may vary depending on several factors (i.e. location of supply lines, interference from ShowerSpa plumbing,
personal preference, etc.)