Specifications

EMC-CS-2009.1
© Copyright Ford Motor Company – All Rights Reserved Page 3 of 121
February 11, 2010
Figure 11-2: RI 112 DUT Harness Configurations...................................................................................................................35
Figure 11-3: RI 114 ALSE Test Setup (1000 – 2000 MHz) excluding Bands 6 and 7.............................................................37
Figure 11-4: RI 114 ALSE Test Setup for Bands 6 and 7 .........................................................................................................39
Figure 11-5: RI 115 Test Setup.................................................................................................................................................42
Figure 11-6: RI 115 Setup for Calibration................................................................................................................................43
Figure 11-7: RI 115 Antenna positioning for testing the harness ..............................................................................................45
Figure 12-1: RI 140 Magnetic Field Immunity Requirements..................................................................................................46
Figure 12-2: RI 140 Magnetic Immunity Test Setup: Radiating Loop .....................................................................................48
Figure 12-3: RI 140 Magnetic Immunity Test Setups for Helmholtz Coil ...............................................................................49
Figure 13-1: RI 130 Default Test Setup....................................................................................................................................51
Figure 14-1: RI 150 Coupled Immunity Requirements ............................................................................................................53
Figure 14-2: RI 150 Test Setup.................................................................................................................................................54
Figure 15-1: CI 210 Requirements ...........................................................................................................................................56
Figure 15-2: CI 210 Test Setup.................................................................................................................................................57
Figure 15-3: CI 210 AC Stress Level (U
S
) Superimposed on DUT Supply Voltage (U
P
) ........................................................58
Figure 16-1: CI 220 Test Setup for Devices with a Single Power Supply Circuit....................................................................60
Figure 16-2: CI 220 Test Setup for Devices with Two Power Supply Connections.................................................................61
Figure 16-3: CI 220 Test Setup for Devices with Input Circuits ..............................................................................................61
Figure 16-4: CI 220 Test Setup Detail (Input Circuits with Remote External Pull-Up Resistor).............................................62
Figure 16-5: CI 220 Test Setup for Application of Pulse G1....................................................................................................62
Figure 16-6: CI 220 Test setup for Application of Pulse G2 .....................................................................................................62
Figure 17-1: CI 230 Power Cycling Waveforms and Timing Sequence...................................................................................65
Figure 17-2: CI 230 Power Cycling Test Setup........................................................................................................................66
Figure 18-1: CI 250 Requirements (Continuous Disturbances)................................................................................................67
Figure 18-2: CI 250 Transient Pulse Detail ..............................................................................................................................68
Figure 18-3: CI 250 Transient Pulse Delay Detail.....................................................................................................................68
Figure 18-4: CI 250 Requirements (Transient Disturbance Sequence) .....................................................................................68
Figure 18-5: CI 250 Test Setup for Ground Offset of DUT .....................................................................................................70
Figure 18-6: CI 250 Signal Source Requirements .....................................................................................................................70
Figure 19-1: CI 260 Waveform A (Voltage Dropout: High) ....................................................................................................73
Figure 19-2: CI 260 Waveform B (Voltage Dropout: Low) .....................................................................................................73
Figure 19-3: CI 260 Waveform C (Single Voltage Dropout) ...................................................................................................74
Figure 19-4: CI 260 Waveform D (Voltage Dip) .....................................................................................................................74
Figure 19-5: CI 260 Waveform E (Battery Recovery)..............................................................................................................75
Figure 19-6: CI 260 Waveform F (Random Bounce) ...............................................................................................................75
Figure 19-7: CI 260 Waveform F (Expanded)..........................................................................................................................76
Figure 19-8: CI 260 Test Setup Detail for Waveforms A , B and C.........................................................................................76
Figure 19-9: CI 260 Test Setup Detail for Waveforms D and E...............................................................................................77
Figure 19-10: CI 260 Test Setup for Waveform F....................................................................................................................77
Figure 21-1: CI 280 ESD Handling Test Setup ........................................................................................................................82
Figure 21-2: CI 280 ESD Powered Test Setup .........................................................................................................................83
Figure 21-3: CI 280 Test setup ( Communication Bus Connection Requirements ).................................................................84