Use and Care Manual

ManualsBrandsPuma ManualsTools & Hardware4 Gal. 2 HP Electric Direct Drive Single Stage Twin Stack Hand Carry Air Compressor

TABLE OF CONTENTS PAGE

AIR COMPRESSOR

1：IMPORTANT SAFETY INSTRUCTION_________________________________

2：GENERAL DESCRIPTION__________________________________________

3：ON RECEIPT INSPECTION_________________________________________

4：GENERAL REQUIREMENT_________________________________________

5：INSTALLATION___________________________________________________

6：COMPRESSOR LUBRICATION______________________________________

7：INITIAL START UP PROCEDURE____________________________________

8：MAINTENANCE CHECK LIST_______________________________________

9：STORAGE_______________________________________________________

10：TROUBLE SHOOTING____________________________________________

3-4

5-7

10-11

OPERATING INSTRUCTION AND PARTS LIST

DIRECT TYPE

IMPORTANT：

PLEASE MAKE CERTAIN THAT THE PERSON WHO IS TO USE THIS

EQUIPMENT CAREFULLY READS AND UNDERSTANDS THESE

INSTRUCTIONS BEFORE STARTING OPERATIONS

Record these numbers in the space below and retain for future reference：

Type：________________________________

Model No：ˍ___________________________

Serial No：_____________________________

Summary of content (6 pages)

PAGE 1
TABLE OF CONTENTS AIR COMPRESSOR PAGE 1：IMPORTANT SAFETY INSTRUCTION_________________________________ 3-4 2：GENERAL DESCRIPTION__________________________________________ 5 3：ON RECEIPT INSPECTION_________________________________________ 5 OPERATING INSTRUCTION AND PARTS LIST 4：GENERAL REQUIREMENT_________________________________________ 5 5：INSTALLATION___________________________________________________ 5-7 6：COMPRESSOR LUBRICATION______________________________________ 8 7：INITIAL START UP PROCEDURE___
PAGE 2
1：IMPORTANT SAFETY INSTRUCTION IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT COULD RESULT IN SERIOUS INJURY AND PROPERTY DAMAGE。 ● BEFORE STARTING COMPRESSOR，PULL SAFETY VALVE RING TO MAKE SURE THE VALVE MOVES FREELY。THE SAFETY VALVE IS FACTORY INSTALLED TO PREVENT THE AIR RECEIVER FROM DAMAGE SHOULD MALFUNCTION OCCUR IN THE PRESSURE SWITCH，IT IS FACTORY SET AT A SPECIFIC LIMIT FOR YOUR PARTICULAR MODEL，AND SHOULD NEVER BE TAMPERED WITH， ADJUSTMENT BY USER WILL AUTOMATICALLY VOID WARRANTY。 1-4：RISK O
PAGE 3
2： GENERAL DESCRIPTION OF AIR COMPRESSOR To compress air，the piston move up and down in the cylinder， During the down-stroke，air is drawn in through the inlet valve，The discharge valve remains closed， On the up-stroke of the piston，air is compressed。The inlet valve closes and compressed air is forced out through the discharge valve、through the check valve and into air receiver tank。Working air is not available until the compressor has raised the air receiver pressure above that required at the air service c
PAGE 4
5-2-3-1：This pressure turn the compressor， it is operated manually but when it is in the “on” position，it allows the compressor to start up or shut down automatically， without warning upon air demand。 Always set this switch to “off” when the compressor is not in use and before unplugging compressor。 6：COMPRESSOR LUBRICATION Do not add or change oil while the compressor is in operation，use the recommended SAE10-30W non-detergent oil only。 6-1：Filling the oil 6-1-1：Remove the oil filler plug。 6-1-2：Slowly p
PAGE 5
10：TROUBLE SHOOTING： CONDITION Before doing any maintenance or adjustments to your air compressor，the following safety precautions should be taken。 A：DISCONNECT ELECTRICAL POWER。 B：DRAIN AIR RECEIVER OF AIR PRESSURE。 CAUSE CORRECTIVE Compressor do not start 1：Loose electrical connection Low pressure 2：Motor overheated 2：Press reset button or wait for automatic reset。 1：Air leak in safety valve。 1：Safety valve manually by pilling upward on ring。If condition persists replace valve。 2：Loose tube of fi
PAGE 6
Compressor over heating 1：Undersized unit for air requirements。 1：Contact PUMA compressor distributor。 2：Compressor location。 2：See installation section。 3：Air leaks in the system 3：Fix leaks。 4：Restricted air filter。 4：Clean or replace filter。 5：Improper grade or level of oil。 5：Replace with SAE10W-30 non-detergent compressor oil。 6：Worn，damage，or carbon build up on valve。 6：Clean，repair or replace valves。 7：Carbon build up at after-cooler 7：Clean or replace。 tube check valve。 Pressure switch 1：P