40” MINI TRAMPOLINE WITH HANDRAIL MODEL# 9040MTH PRODUCT MANUAL - VERSION 08.17.08 FOR AGES: 13+ WEIGHT LIMIT: 220 Lbs 100 Kgs TO BUILD: X TOOLS NEEDED: 1 CUSTOMER SERVICE GQBrands.com CustomerService@GQBrands.
CUSTOMER SERVICE INFORMATION Thank you for purchasing: 40” MINI TRAMPOLINE WITH HANDRAIL MODEL# 9040MTH To order these parts, or if you have any other questions or concerns about this GQBrands product, please contact us at At GQBrands®, we want all of our customers to be completely satisfied with their purchase. Take time to review the contents of the product you have just received to make sure that all of the parts are included.
LIMITED WARRANTY ADULT ASSEMBLY REQUIRED CHOKING HAZARD - Small Parts NOT for children under 3 years of age. Please read these warnings and the information in this manual in its entirety. Failure to comply with the following instructions may increase the risk of serious injury and/or death: • This unit is designed only for jogging in place and similar bounding exercises. • Not recommended for children under 13 years of age. • Maximum weight limit: 220lbs.
PARTS LIST 2 - Jumping Mat 1 - Frame x1 x1 5 - T-Section Piece 3 - Spring 6 - Cross-Section Piece 7 - 40mm Carriage Bolt x36 x12 x8 4 - W-Hook x4 8 - 50mm Carriage Bolt x18 9 - Nut 10 - Washer x4 11 - Frame Pad 12 - Leg with Cap x8 x16 x1 13 - Straight Pole x6 15 - U-Shaped Bracket 14 - Handle Bar with Foam Grip x4 x1 x2 4 GQBrands.com CustomerService@GQBrands.
ASSEMBLY INSTRUCTIONS STEP 1: Assembled Frame NOTE: The Frame Pad (Part 11) may be already attached to the Frame, remove it and place it aside until Step 4 The Frame (Part 1), Jumping Mat (Part 2), Springs (Part 3), & W-Hooks (Part 4) should be assembled in one piece. Place assembled Frame on an even, clean, & flat surface to install. Make sure that there are no obstructions in your way when building the Mini Trampoline.
ASSEMBLY INSTRUCTIONS STEP 2: Parts: 8x T-Section Pieces (Part 5) 4x 40mm Square Neck Bolts (Part 7) 4x Nuts (Part 9) 4x U-Shaped Bracket (Part 15) Locate the (A) openings in the frame (Shown in Page 5) to begin installing the T-Sections Pieces into the Frame. (5) (5) Square Opening Round Opening (15) A. Place a T-Section Piece on the outside of the frame and the other half from the inside of the Frame. Make sure that the T-Sections are facing up to install the legs in Step 6.
ASSEMBLY INSTRUCTIONS STEP 3: A Parts: 4x Cross-Section Pieces (Part 6) 4x 50mm Square Neck Bolts (Part 8) 4x Nuts (Part 9) 4x Washers (Part 10) (6) Locate the (B) openings in the frame (Shown in Page 5) to begin installing the Cross-Sections Pieces into the Frame. (6) A. Place a Cross-Section Piece on the outside of the frame and the other half from the inside of the Frame. All openings should line up. B.
ASSEMBLY INSTRUCTIONS STEP 4: A Parts: 1x Frame Pad (Part 11) A. Flip the Assembled Frame in order to place the Frame Pad (11). (11) Make sure to locate all six loops in the Frame Pad, two of them should have two openings assigned for the Cross-Section Pieces. Place on top Frame to cover the Frame & Jumping Mat. B. For the T-Sections, hook all loops in the inserts openings of the T-sections before installing the legs. C.
ASSEMBLY INSTRUCTIONS STEP 5: Parts: 6x Legs with Caps (Part 12) NOTE: If the Caps from the Leg Poles are not already placed after unboxing, make sure to insert them on the opposite side of where the openings are located as shown. This will make sure that the openings are clear when installing into the Frame. Repeat this process until you have all six assembled Legs with Caps. (12) x6 Assembled Legs STEP 6: Place all assembled legs inside the inserts.
ASSEMBLY INSTRUCTIONS STEP 8: A Facing Center Facing Center Parts: 2x Straight Pole (Part 13) 2x 40mm Square Neck Bolts (Part 7) 2x Nuts (Part 9) 2x Washers (Part 10) A. Insert x2 Straight Poles (13) into the upper openings of the Cross-Sections. NOTE: Straight poles upper openings must face the center of the trampoline. B. Locate x2 40mmm Square Neck Bolts (7), x2 Washers (10), and x2 Nuts (9). Insert a Bolt from the inside facing out to each Straight Pole. Tighten both with a Washer & Nut.
ASSEMBLY INSTRUCTIONS STEP 9: (14) Parts: 1x Handle Bar with Foam Grip(Part 14) Place Handle Bar with Foam Grip (14) on top of Straight Poles. Both ends must be inserted at the same time. Stop when you hear both the buttons “Snap & Click” in the openings. To adjust to your desired height, simply press the buttons in and slide the pole to a desired opening. IMPORTANT: Handle Bar must be snapped on the same height for both openings. Failure to do this will cause the Poles to bend, snap, or break.
NOTES CUSTOMER SERVICE GQBrands® 1-866-498-5269 CustomerService@GQBrands.com 4401 Samuell Blvd, Ste 150 Mesquite, TX 75149 12 GQBrands.com CustomerService@GQBrands.
