DURA-BOUNCE 15FT TRAMPOLINE SET MODEL# 9315TS PRODUCT MANUAL - VERSION 5.20.01 FOR AGES: 6+ WEIGHT LIMIT: 350 Lbs 158 Kgs TO BUILD: X TOOLS NEEDED: 2 CUSTOMER SERVICE GQBrands.com CustomerService@GQBrands.
CUSTOMER SERVICE INFORMATION Thank you for purchasing: DURA-BOUNCE 15FT TRAMPOLINE SET MODEL# 9315TS If you have an issue with your item, do not return. Please report items that are damaged or missing parts to the manufacturer GQ Brands within three days of delivery. Contact customer service at customerservice@gqbrands.com to open a ticket. To register you product please visit: www.globalqualitybrands.
WARNINGS ADULT ASSEMBLY REQUIRED CHOKING HAZARD - Small Parts NOT for children under 3 years of age. Please read these warnings and the information in this manual in its entirety. Failure to comply with the following instructions may increase the risk of serious injury and/or death: • It is essential that the intended site for this trampoline is completely flat and level. If the ground is not level this will cause movement in the frame and could cause stress on the joined sections.
TRAMPOLINE PARTS LIST 1- Jump Mat 2- Curved Top Rail x12 x1 3- T-Section 4- M8x50mm Bolt & Nut 6- Leg Extension x12 x12 x12 5- M6x50mm Bolt & Nut x12 7- U-Shaped Leg 8- Screw 9- Spring x12 x108 x6 10- Frame Pad x1 4 GQBrands.com CustomerService@GQBrands.
TRAMPOLINE ASSEMBLY INSTRUCTIONS STEP 1: Gather all 12 Curved Top Rails (Part 2), flip them over so the spring holes are touching the floor. Separate them into 3 groups of 4 Top Rails. Make sure to place them all on a flat and secure surface before you begin. NOTE: The Curved Top Rail has 9 spring holes in the top section. The bottom should be smooth.
TRAMPOLINE ASSEMBLY INSTRUCTIONS A STEP 4: B A. Gather all Leg Extensions (Part 6) and begin inserting them into the T-Sections NOTE: The Leg Extension will have 3 openings. The 2 square openings closest to each other, will go inside the T-Section. Make sure that wider section is facing the center of the trampoline. B.
TRAMPOLINE ASSEMBLY INSTRUCTIONS STEP 6: Use the Screw (Part 8) with a Phillips screwdriver to secure the Leg Extension to the U Shaped Leg. NOTE: It is recommended to use a powered screwdriver to accomplish this task safely. 1 STEP 7: Once all 3 groups have been successfully completed, flip them over so they may stand. You may start connecting all ends to one another in order to complete the frame. NOTE: It is recommended that you use the help of 2 more adults in order to attach all groups together.
TRAMPOLINE ASSEMBLY INSTRUCTIONS 10 STEP 8: Place the Jump Mat (Part 1) in the middle of the frame and unfold it completely. 1 11 NOTE: Make sure the stitching of the Jump mat is facing the floor 5 7 In order to avoid ripping and to distribute tension when attaching springs to the frame, follow the numbered order shown. 14 16 Once a spring is attached to the Jumping mat, you must attach the other in the opposite direction of the mat.
TRAMPOLINE ASSEMBLY INSTRUCTIONS STEP 9: Unfold the Frame Pad (Part 10) and place it on top of the Top Rail and springs. The skirt of the Frame Pad must cover the Top Rails completely to avoid injury. NOTE: Make sure the connecting straps are facing the Top Rails in order to secure the Frame Pad to them in Step 10. STEP 10: Find all the bottom connecting straps of the trampoline frame pad and secure them by tying them in a not on to the top rails to avoid moving or shuffling when jumping on the trampoline.
ENCLOSURE PARTS LIST 1- Straight Enclosure Pole x6 2- Curved Enclosure Pole x6 3- Enclosure Pole Cap 9- Enclosure x6 4- M6x80mm Bolt x12 x1 5- Thick Curved Plastic Washer x12 6- Washer x12 7- Nut x12 8- Black Nut Cap x12 10 GQBrands.com CustomerService@GQBrands.
ENCLOSURE ASSEMBLY INSTRUCTIONS STEP 1: Gather all Curved Enclosure Poles (Part 2) and Enclosure Pole Caps (Part 3). IMPORTANT: Do not attach the Enclosure Pole Caps to the Straight Enclosure Poles. Once an Enclosure Pole Cap has been installed it cannot be removed. Snap and click all Enclosure Pole caps to the Curved Enclosure Pole. The button must be pushed down, and you will hear a click once successfully attached.
ENCLOSURE ASSEMBLY INSTRUCTIONS STEP 3: A. Remove the Bolt and Nut from 15FT Enclosure Trampoline on the right side of the U-Shaped Leg. Do not remove all nuts and bolts at the same time, only 1 set a time to keep the strength of the Frame at all times. NOTE: Make sure to keep removed parts stored or in a safe place away from the mat while building the Enclosure. B. With the help of another adult, hold the completed enclosure pole by aligning both square holes to begin installation.
ENCLOSURE ASSEMBLY INSTRUCTIONS 4 M6x80mm Bolt MODEL# 9315TS - ENCLOSURE 5 6 Spacer Washer 7 8 Nut Black Nut Cap 4 5 6 7 8 4 5 6 7 8 13
ENCLOSURE ASSEMBLY INSTRUCTIONS STEP 4: Place the Enclosure Net (Part 9) on top of the trampoline. Align the straps to the corresponding Enclosure Poles so they are as near to each other as possible when lifted NOTE: Make sure that zipper and buckle snap are facing the outside of the trampoline. This is good to ensure that Enclosure is not reversed.
ENCLOSURE ASSEMBLY INSTRUCTIONS STEP 6: A B C D A. To attach the enclosure net to the Pole Caps, grab the corresponding strap at the top of the Enclosure Net and slip through the opening of the Pole cap. B. Detach the snaps by pushing on the middle of the buckle. C. Connect Male Buckle Snap (Fork Side) to the strap. D. Once Male Buckle snap is fastened, Re-attach to the other side of the buckle. E MODEL# 9315TS - ENCLOSURE E. You will successfully connect both sides when you hear them click.
FREQUENTLY ASKED QUESTIONS • Question: “The foam padding or mat is damaged, what should I do?” Answer: If you are still within your warranty period (90 Days from initial purchase) you should contact customer service. You can also purchase replacement padding and mats at: www.PureFun.