48” SUPER JUMPER KIDS TRAMPOLINE MODEL# 9009SJ PRODUCT MANUAL - VERSION 2.19.1 FOR AGES: 3-10 WEIGHT LIMIT: 100 Lbs 45 Kgs TO BUILD: X TOOLS NEEDED: 1 CUSTOMER SERVICE GQBrands.com • CustomerService@GQBrands.
CUSTOMER SERVICE INFORMATION Thank you for purchasing: 48” SUPER JUMPER KIDS TRAMPOLINE MODEL# 9009SJ To order these parts, or if you have any other questions or concerns about this GQBrands product, please contact us at If you have an issue with your item, do not return. Please report items that are damaged or missing parts to the manufacturer GQ Brands within three days of delivery. Contact customer service at customerservice@gqbrands.com or toll-free at 1-866-498-5269 PureFun.
WARNINGS ADULT ASSEMBLY REQUIRED CHOKING HAZARD - Small Parts NOT for children under 3 years of age. Please read these warnings and the information in this manual in its entirety. Failure to comply with the following instructions may increase the risk of serious injury and/or death: • This unit must be assembled and disassembled by ADULTS ONLY. • Children must be supervised at all times when using this equipment. DO NOT leave children unattended at any time.
PARTS LIST 1 - Top Rail 2- 3 - N/A T-Joint 4 - Leg Cap Not available in this version 5- x6 6- x6 Jump Mat with Mesh x6 Frame Pad x1 x1 7R - Hand Rail Base - Right 7L - Hand Rail Base - Left 8- 9- Side Hand Rail Center Hand Rail x2 x1 10 - x1 11 - Hex Nut Bolt x12 15- x1 4 x12 16- Wrench x1 12 - Safety Nut Cap 13 - Plastic Washer x12 x12 14 - Spring x42 T-Hook Spring Tool x1 GQBrands.com CustomerService@GQBrands.
ASSEMBLY INSTRUCTIONS NOTE: Make sure that you assemble the T-Section/Legs to the Top Rail as shown to be certain that the pre-drilled spring holes are facing in the correct direction when you attach the springs. 1 STEP 1: A. Slide a T-Joint (Part 2) onto the end of a Top Rail (Part 1). Next, slide the end of another Top Rail into this T-Section so that each Top Rail can be bolted to one side of the T-Section.
ASSEMBLY INSTRUCTIONS STEP 2: 2 Slide 1x Hand Rail Base - Left (Part 7L) and slide 1x Leg Cap (Part 4) into a T-Joint to secure it. (4) Then Slide 1x Hand Base Rail - Right (Part 7R) one leg apart from the Left side as shown on to a T-Joint, and secure with 1x Leg Cap (Part 4). (4) LEFT (7L) (4) RIGHT (7R) (4) (4) (4) NOTE: The Hand Rail Bases (Parts 7L & 7R) need to have one leg in between to be able to have enough distance to connect.
ASSEMBLY INSTRUCTIONS 4 STEP 4: 4 Using the T-Hook Spring Tool (Part 16), attach eight initial springs (Part 14) directly across from each other at “compass points” as shown. 5 1 7 NOTE: Only use the T-Hook Spring Tool included with this product to attach the springs. NEVER use your hands only or other household tools to attach these springs. 8 6 We suggest that you count the V-rings on the mat as they line up to the holes in the top rail before continuing.
ASSEMBLY INSTRUCTIONS STEP 6: 6 Place the Frame Pad (Part 6) on top the Jumping Mat. Stretch the Frame Pad so it completely covers all Springs and the Mesh of the Jumping Mat. NOTE: Make sure all springs are completely covered to avoid any injury while in use. 8 GQBrands.com CustomerService@GQBrands.
ASSEMBLY INSTRUCTIONS 7 STEP 7: Attach 2x Side Hand Rails (Part 8) by placing the end into the Hand Rail Base. Secure with the push pins buttons located on the Hand Rails. Make sure that the push buttons are fully secure in the Hand Rail Base. 8 STEP 8: Secure the Center Hand Rail (Part 9) by attaching it to the Side Hand Rails as shown. Secure with the push pin buttons located in the Hand Rails. Make sure this connection is secure before continuing.
NOTES CUSTOMER SERVICE GQBrands® 1-866-498-5269 CustomerService@GQBrands.com 4401 Samuell Blvd, Ste 150, Mesquite, TX 75149 10 GQBrands.com CustomerService@GQBrands.
