KIDS ROCKER SEESAW MODEL# 9306RS PRODUCT MANUAL - VERSION 2.19.1 FOR AGES: 3-7 WEIGHT LIMIT: TO BUILD: 150 Lbs 68 Kgs X TOOLS NEEDED: 1 Manual en español ubicado en GQBrands.com Spanish Manual located at GQBrands.com CUSTOMER SERVICE GQBrands.com • CustomerService@GQBrands.
CUSTOMER SERVICE INFORMATION Thank you for purchasing: KIDS ROCKER SEESAW MODEL# 9306RS To order these parts, or if you have any other questions or concerns about this GQBrands product, please contact us at Please do not return your item. Please report items that are damaged or missing parts to the manufacturer GQ Brands within 3days of delivery. Email customerservice@gqbrands.com or call toll-free at 1-866-498-5269 PureFun.Net GQBrands® Phone: 1-866-498-5269 Email: CustomerService@GQBrands.
WARNINGS ADULT ASSEMBLY REQUIRED CHOKING HAZARD - Small Parts NOT for children under 3 years of age. Please read these warnings and the information in this manual in its entirety. Failure to comply with the following instructions may increase the risk of serious injury and/or death: • Please read these warnings and the information in this manual in its entirety.
PARTS LIST 1 - Base Rails 2 - Foam Rocker Bar x2 x2 3 - Handle Tube 4 - Backrest x2 x2 4 GQBrands.com CustomerService@GQBrands.
PARTS LIST 5 - Footrest Tube 6 - Seats x5 x2 7 - M6 45mm Bolt 8 - M6 40mm Bolt x16 10 - Square Nuts x20 14 - Flat Cap (Large) 9 - M6 50mm Bolt x20 11 - Hex Nut x4 12 - Washer x20 13 - Safety Caps x20 15 - Flat Cap (Small) x20 16 - Round Cap x4 MODEL#9306RS 5
ASSEMBLY INSTRUCTIONS STEP 1 Parts: Part 1 (x2) - Base Rails Part 6 (x1) - Seat Place both Base Rails (Part 1) in a flat surface free of obstructions. Place 1x Seat (Part 6) with the flat surface facing the floor and align the side openings to the middle openings of the Base Rails.
ASSEMBLY INSTRUCTIONS STEP 3 Parts: Part 6 (x4) - Seats Part 10 (x12) - Square Nuts Part 8 (x12) - M6 40mm Bolt Place the remainder of the Seats at the end of the Base Rails with the flat surface of the Seats facing the floor. Place 2x on each side as shown. Align the side openings to the corresponding Base Rails opening. 6 6 Place the Square Nuts (Part 10) at the end gaps of the Seat openings, and secure with a M6 40mm Bolt (Part 8) aligned by the Base Rail and Seat openings.
ASSEMBLY INSTRUCTIONS STEP 4 Parts: Part 2 (x2) - Foam Rocker Bar Part 7 (x4) - M6 45mm Bolt Part 11 (x4) - Hex nut Part 12 (x4) - Washer 2 NOTE: Round Cap (Part 16) is already installed on the Foam Rocker Bar (Part 12). If not, slide to both ends and make sure the tub ends are covered 2 Place the Foam Rocker Bars (Part 2) on the outside of the Base Rails facing away from the Seats. 11 12 Align the opening of the tip of the Base Rails to the opening under the Round Cap of the Foam Rocker Bars.
ASSEMBLY INSTRUCTIONS STEP 6 Parts: Part 3 (x2) - Handle Tube Part 5 (x2) - Footrest Tube Part 8 (x4) - M6 40mm Bolt Part 11 (x4) - Hex Nut Part 12 (x4) - Washer 5 3 Locate the middle openings in the Handle Tube (Part 3), and align to the openings at the tips of the Footrest Tube (Part 5). Tighten with a M6 40mm Bolt (Part 8), Hex Nut (Part 11), and Washer (Part 12). Repeat until you have 2x completed Handle Tubes with the Footrest Tubes installed.
ASSEMBLY INSTRUCTIONS STEP 7 Insert the Assembled Handles on the inside of the Seesaw. Align the upper openings of the Handle Tubes to the Base Rails, and bottom openings to the Foam Rocker Bars STEP 8 Parts: Part 9 (x4) - M6 50mm Bolt Part 11 (x4) - Hex nut Part 12 (x4) - Washer Locate the aligned middle openings in the Handle Bar. Tighten with a M6 50mm Bolt (Part 9), Hex Nut (Part 11), and Washer (Part 12).
ASSEMBLY INSTRUCTIONS STEP 9 Parts: Part 7 (x4) - M6 45mm Bolt Part 11 (x4) - Hex nut Part 12 (x4) - Washer Locate the aligned bottom openings in the Handle Bar. Tighten with a M6 45mm Bolt (Part 7), Hex Nut (Part 11), and Washer (Part 12). Hide the head of the Bolt under the foam of the Foam Rock Bars. NOTE: Make sure the head of the Bolts are facing the outside of the Seesaw to avoid scratches or scrapes when in use.
ASSEMBLY INSTRUCTIONS STEP 10 Parts: Part 4 (x2) - Backrest 4 4 Insert the Backrest (Part 4) from the outside of the Base Rails and slide the tips on the inside of the Rocker Seesaw. Align the openings of the tips to the Foam Rocker Bars to the Backrest to install the hardware in Step 11. STEP 11 Parts: Part 7 (x4) - M6 45mm Bolt Part 11 (x4) - Hex nut Part 12 (x4) - Washer 7 12 Tighten the tips to the foam rocker. Hide the head of the Bolt under the foam of the Foam Rock Bars once installed.
ASSEMBLY INSTRUCTIONS STEP 12 7 Parts: Part 7 (x4) - M6 45mm Bolt Part 10 (x4) - Square Nuts Flip the Rocker Seesaw over to install the Seats into the Base Rail and Backrests. 10 Place the Square Nuts (Part 10) at the end gaps of the Seat openings, and secure with a M6 38mm Bolt (Part 8A) aligned by the Base Rail, Backrest, and Seat openings. STEP 13 Parts: Part 13 (x20) - Safety Caps x20 Use the Safety Caps (Part 13) to hide any excess from the Bolts.
FREQUENTLY ASKED QUESTIONS • Question: “How should I clean my seesaw?” Answer: you should clean the Seesaw with a solution of warm water and Non- Corrosive/Abrasive soap. Dampen a rag with this solution and wipe completely dry before using. • Question: “Is there any maintenance I need to do for my seesaw?” • Question: “A seat seems loose, what should I do?” Answer: Make sure the Bolts/Nuts under the plastic seat are secure.
NOTES CUSTOMER SERVICE GQBrands® 1-866-498-5269 CustomerService@GQBrands.
